_dvHAMaster.png?sw=960&sh=960&sm=fit&sfrm=png)
Reference 475a
4-Channel Full-Range Amplifier
Sold from 2007 until now
| Predecessor Product: | REFERENCE 7541A |
|---|---|
| Made in: | Netherlands |
Documents & Downloads
Product Specifications
- Signal-to-noise ratio
- 85dBA (reference 1 watt into 4 ohms)
- Dynamic power
- 117 watts at 2 ohms
- Effective damping factor
- 6.3 at 4 ohms
- Frequency response
- 10Hz – 100Hz (–3dB)
- Maximum input signal
- 6V
- Maximum sensitivity
- 100mV
- CEA Rated
- Yes
- Amplifier Power (RMS)
- 180 watts x 2 channel @ 4 ohms, 14.4V supply and ≤1% THD + N
- Amplifier Power (RMS)
- 75 watts x 4 channel @ 4 ohms, 14.4V supply and ≤1% THD + N
- Signal-to-Noise Ratio
- 85dBA (reference 1 watt into 4 ohms)
- Dynamic Power
- 117 watts @ 2 ohms
- Effective Damping Factor
- 6.315 @ 4 ohms
- Frequency Response
- 10Hz – 100kHz (-3dB)
- Maximum Input Signal
- 6V
- Input Sensitivity
- MAXIMUM... 100mV
- MSRP U.S.
- $279.95 each
- Dimensions (L x W x H)
- 14-3/16" x 9" x 2-11/16" (360mm x 229mm x 68mm)
4-Channel full-range amplifier with on-board electronic crossover and variable bass boost.
Efficiency is the benefit of the Infinity Reference Series Class D subwoofer amplifiers. A higher percentage of the power the amp extracts from the car’s charging system is converted into output to the speakers, and less is wasted as heat. That is really important if you're trying to provide power to a 1000-watt amplifier. Class D technology turns the analog input signal into a series of pulses that can be amplified more efficiently by transistors used as switches, rather than valves. They're either on and operating at their most efficient level, or they’re off. The pulses are converted back into an analog signal by an output filter.
All Infinity amplifiers are tested in accordance with CEA-2006, which provides a testing procedure to help customers compare amplifiers accurately – apples to apples. Specs are based on industry-accepted standards, rather than on the whims of amplifier companies’ marketing departments. Look for the CEA-2006 logo when comparing amplifiers, to be sure you’re getting the power you’re paying for.
Class AB full-range amplifiers offer audiophilequality performance and the best compromise between efficiency, low distortion, maximum available headroom and output power.
provides superior control and adjustability, compared to traditional bass-boost. DBO is a 2nd order high-pass filter that can be adjusted between 20Hz and 80Hz. The boost (or Q) adjustment boosts the signal above the highpass filter frequency. Used with a sealed box, it can help to increase output for more “fun” if it’s set to about 45Hz. If it’s used with a vented box, it should be set at or slightly below the tuned frequency of the box. That will prevent woofer unloading, and provide more output at the frequency where the box is tuned and the woofer’s excursion is minimized – where it can handle more power.
Reference Series amplifiers include 2nd order (12dB/octave) slopes and are continuously variable from 32Hz to 200Hz.
provides up to 12dB of boost at 50Hz in the Reference Series full-range amplifiers.
eliminate the need for additional solder-on or crimp-on terminals and provide an easy and reliable connection for power, ground and speaker wires.
eliminate the need for signal splitters.
The amount of bass in popular recordings differs greatly from track to track. Give your customer as much control as you see fit with the RLC. It varies the output of the amplifier from no output up to the maximum output level that you set with the input sensitivity control.
Images & Videos
_dvHAMaster.png?sw=300&sh=300&sm=fit&sfrm=png)
_dvHAMaster.png?sw=300&sh=300&sm=fit&sfrm=png)
_dvHAMaster.png?sw=300&sh=300&sm=fit&sfrm=png)
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
