AVR 2600
Audio/Video Receiver With Dolby TrueHD & DTS-HD Master Audio, HDMI 1.3A & 1080p Upscaling (65 watts x 7)
Sold from 2009 until 2012
| Successor Product: | AVR 2650 |
|---|---|
| Made in: | China |
Documents & Downloads
Product Specifications
- Power Consumption (full power/idle)
- 120W idle, 1405W maximum
- Transient intermodulation distortion (TIM):
- Unmeasurable
- Power Requirement
- AC 120V/60Hz
- Power Requirements
- AC 120V/60Hz
- Power Consumption
- 65W idle, 540W maximum (7 channels driven)
- Digital Inputs (coaxial/optical)
- 2/2 on rear; 1/1 on front
- HDMI
- Four inputs/1 output, with audio and video processing. HDMI v.1.4a with 3D.
- Analog Inputs
- 1 A/V on front panel
- Analog Inputs
- 2 audio-only
- Analog Inputs
- 4 A/V on rear panel
- Analog Inputs
- 6-/8-channel input
- Analog Inputs
- stereo jack
- Analog Inputs
- tuner
- On-Screen Display
- Yes, with component video and HDMI
- Multizone Capability
- Yes, by reassigning surround back channels only
- Auto Setup
- EzSet/EQ room equalization
- Remote Control
- Seven-device, programmable remote
- MSRP U.S.
- $799.95 each
- Distortion (Mono/Stereo)
- 0.2/0.3%
- Frequency Response
- 10Hz –130kHz
- Surround system adjacent-channel separation:
- Pro Logic® I/II 40dB Dolby® Digital (AC-3) 55dB DTS® 55dB
- High Instantaneous Current Capability
- ±60 Amps
- Input Level/Impedence (ohm)
- 1Vp-p/75 ohms
- Stereo Separation @ 1kHz (dB)
- 40dB @ 1kHz
- Output Level/Impedence (ohm)
- 1Vp-p/75 ohms
- Signal-to-Noise Ratio (dB)
- 45dB
- Signal-to-Noise Ratio (Mono/Stereo dB)
- Mono/Stereo 70/68dB
- Selectivity (±400kHz):
- 70dB
- Signal-to-noise Ratio (IHF-A) (dB)
- 100dB
- Usable Sensitivity (Loop)
- 500?V
- Frequency Range (kHz)
- 520–1720kHz
- Input Sensitivity/Impedence
- 200mV/47k ohms
- Distortion (1kHz, 50% mod):
- 1kHz, 50% Mod 0.8%
- Stereo Power
- 65 Watts per channel, 20Hz–20kHz, @ <0.07% THD, both channels driven into 8 ohms
- Frequency Range (MHz)
- 87.5–108.0MHz
- Slew Rate
- 40V/sec
- Usable Sensitivity (IHF)
- IHF 1.3?V/13.2dBf
- Selectivity (±10kHz):
- 30dB
- # of Amplifier Channels
- 7
- Continuous Average Power (FTC) per Channel (stereo mode)
- 65 Watts per channel, 20Hz – 20kHz, @ <0.07% THD, both channels driven into 8 ohms
- Front L & R Channels
- 65 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Center Channel
- 65 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Surround Channels (L & R Side, L & R Back)
- 65 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Input Level/Impedance
- 200mV/47k ohms - Linear (High-Level)
- Signal-to-Noise Ratio
- 100dB (IHF-A)
- Surround System Adjacent Channel Separation:
- Dolby Pro Logic I and II
- 40dB
- Dolby Digital
- 55dB
- DTS
- 55dB
- Frequency Response
- 10Hz – 130kHz (+0/-3dB @ 1 watt)
- Transient Intermodulation Distortion (TIM)
- Unmeasurable
- Slew Rate
- 40V/µsec
- Height (mm)
- 165
- Depth (in)
- 17-1/16
- Width (mm)
- 440
- Depth (mm)
- 435
- Height (in)
- 6-1/2
- Weight(kg)
- 20
- Width (in)
- 17-5/16
- Width
- 17-5/16 inch (440mm)
- Height
- 6-1/2 inch (165mm)
- Depth
- 17-1/16 inch (435mm)
- Weight
- 26lbs
- Shipping Weight (System, Accessories, Packing)
- 32lbs
- Carton Dimensions (W x H x D)
- 21-7/8 inch x 10-1/2 inch x 18-5/16 inch (555mm x 266mm x 465mm)
- Video Frequency Response (Component Video)
- 10Hz–100MHz (–3dB)
- IF Rejection (dB)
- 90dB
- Television Format
- NTSC
- Image Rejection (dB)
- 80dB
- Input Level/Impedance
- 1Vp-p/75 ohms
- Output Level/Impedance
- 1V/75 ohms
- Video Frequency Response
- 10Hz–100MHz (–3dB)
- Composite and S-Video
- 10Hz – 8MHz (–3dB)
- Component Video
- 10Hz – 100MHz (–3dB)
- HDMI
- HDMI v.1.4a with 3D.
- Frequency Range
- AM... 520kHz – 1720kHz
- Frequency Range
- FM... 87.5MHz – 108.0MHz
- Signal-to-Noise Ratio
- AM... 45dB
- Usable Sensitivity
- FM... IHF 1.3µV/13.2dBf
- Signal-to-Noise Ratio
- FM... Mono/Stereo 70/68dB
- Usable Sensitivity
- AM... Loop 500µV
- Distortion
- AM... 1kHz, 50% Mod 0.8%
- Distortion
- FM... Mono/Stereo 0.2/0.3%
- Selectivity
- AM... ± 10kHz, 30dB
- Stereo Separation
- FM... 40dB @ 1kHz
- Selectivity
- FM... ± 400kHz, 70dB
- Image Rejection
- FM... 80dB
- IF Rejection
- FM... 90dB
- Amplifier Power (RMS)
- 65 x 7 @ 8 ohms (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
- High Instantaneous Current Capability (HCC)
- ± 35 Amps
A 7.1-channel A/V receiver with HDMI 3D plus Dolby, DTS and Logic 7 surround.
The AVR 2600 is designed to delight the most discerning home theater enthusiast. With its high-definition on-screen interface and Logic 7® technology, the AVR 2600 is prepared to bring the home theater experience to an entirely new level. Along with its state-of-the-art Faroudja DCDi Cinema™ processing, Dolby® audio technology and HDMI® v.1.4A playback with 3-D capability, this home theater powerhouse can even sync up with The Bridge III docking station (available separately), allowing you to enjoy movies, music, or multimedia files straight from your iPod® or iPhone®.
The AVR 2600 high-performance receiver delivers 65 watts per channel with the ability to power a full 7.1-channel surround-sound system. A high-current capability (HCC), ultrawide-bandwidth amplifier design ensures accurate, dynamic sound with enhanced clarity and realism, even at the highest listening levels. You can also connect the AVR 2600 to a powered subwoofer to generate additional low-frequency excitement.
Four HDMI inputs with 3D and Deep Color deliver high-definition digital video at resolutions up to 1080p with full-fidelity audio through a single cable. There is no loss of video or audio quality because of format conversion, just full-impact Hollywood excitement as its creators meant you to experience it.
The AVR 2600 delivers high-resolution audio to match the digital video of Blu-ray Disc formats, unlocking the full potential of movie soundtracks formatted with Dolby TrueHD and DTS-HD Master Audio coding. No matter what mode or mood you are in, you’ll always hear playback at its finest.
Dolby Volume technology maintains the same volume level no matter what entertainment you’re viewing. You need to set the AVR 2600 volume level only once to eliminate unpredictable volume differences among TV shows, commercials and movies.
HARMAN Logic 7 technology transforms a stereo input into full 7.1-channel surround sound, courtesy of proprietary algorithms that make any audio source – HDMI, analog, component, composite or computer-based audio from a USB connection – truly spectacular. The result is optimal quality and a superior, enveloping experience that engulfs you in a 360-degree soundscape.
Four HDMI input ports let you digitally interconnect your entire system for maximum audio/video performance. HDMI-format ports dramatically reduce connection confusion while ensuring the greatest chance for compatibility with whatever audio/video equipment you are planning to connect.
The HARMAN EzSet/EQ™ auto-calibration process tailors the AVR 2600’s loudspeaker outputs to match playback volume levels for your specific room conditions automatically. The system features an easy-to-follow menu display and a plug-in calibration microphone.
The optional Harman Kardon The Bridge IIIP docking station (sold separately) works with an Apple iPod or iPhone to expand your entertainment options beyond DVD and Blu-ray Disc media. Once connected, The Bridge III even charges your Apple device and works seamlessly with the AVR 2600’s system remote control to navigate and play your favorite music and video tracks.
Faroudja DCDi Cinema processing dramatically reduces video artifacts from digital or analog signals. The result is fewer lines and a smoother picture – especially when there is movement across your TV screen. Faroudja DCDi Cinema technology also upscales lower-resolution video to the 1080p high-definition standard, thereby extending the life of your movie library.
A built-in MP3 enhancer dramatically improves bass performance when replaying compressed-audio tracks, thereby elevating the sound quality of your favorite songs without the need for additional audio equipment.
Images & Videos
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
