How To
How To
670 results
-
The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.Was this helpful? Thank you for your feedback!
-
Any changes you make on the Lighting page will be immediately reflected on your headset.Was this helpful? Thank you for your feedback!
-
Here is the pairing procedure between a K915 headset and a new transmitter box: 1. Power off the headphone. 2. Power off the transmitter. 3. Press and hold the power button on the headphone until the “Signal” LED is flashing, and a beep sound can be heard. 4. Power on the transmitter. 5. After a short while the “Signal” LED will light constantly (stop flashing) and the pairing is complete.Was this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
JBL QuantumSURROUND takes up to 8 channels of audio, and recreates a multi-channel setup—including overhead channels—as measured inside one of JBL’s listening rooms. You’ll hear the multi-channel mix as if you’re right in the middle of the game.Was this helpful? Thank you for your feedback!
-
For models E40BT and E50BT Connect the first headphone by BT to your mobile device Tap the ShareMe button once Tap the ShareMe button on the 2nd headphones twice ( ! ) The headphones will connect to each other. When changing volume on source device, or BT connected headphones, the volume will only change on THAT headphone ( and in some cases the source device, like iOS devices and newer Android ), not on the one connected via ShareMe. When changing volume on a via-ShareMe-connected headphone ( 2nd ), it will not change volume on source device, or on the BT-connected headphone. To sum up, both headphones have their individual volumes. For Everest models ( not ELITE ). Connect the headphones by BT to your mobile device Put the 2nd device ( speaker, headphones as long as they have Bluetooth ) in "BT discovery mode" Press the ShareMe button on the Everest headphone ( button marked with a little "s" ) The Everest will connect to BT device. (Please note that you may not be able to pair from the Everest to the Everest Elite models, or if you can pair, you may have dropouts in sound). When changing volume on source device, or Everest, the volume will only change on the Everest ( and in some cases the source device, like iOS devices and newer Android ), not on the device connected via ShareMe. When changing volume on via-ShareMe-connected BT device ( 2nd ), it will not change volume on source device or Everest. Please note that it is NOT possible to use ShareMe if you are listening to analog signal via cable. Bot the E-series and the Everest models will switch off the Bluetooth circuits as soon as you insert the audio cable, so re-transmission is not possible.Was this helpful? Thank you for your feedback!
-
Vi measures heart rate using an optical heart rate sensor in the left earbud. The sensor emits light in a specific wavelength to the tissue of the tragus in the ear, and the reflective light is captured by the receiver of the sensor, that is processed by a proprietary algorithm to capture the heart rate. If you need assistance getting an accurate and consistent heart rate, check out this tutorial video to find the correct fit.Was this helpful? Thank you for your feedback!
-
Press the microphone button (located on the LEFT arm) to turn on the first RunSafe mode. The first mode blinks continually. When you press the microphone again, the second mode is initiated which features 2 blinks on followed by 2 seconds without. Pressing the microphone again is the third mode which is 3 blinks on followed by 3 seconds without.Was this helpful? Thank you for your feedback!
-
Make sure the headphones are turned on and connected to your smart device. Press and hold the Microphone button located on the LEFT arm of the neckband. You should be able to activate Siri/Google within 3 seconds after pressing the Microphone button.Was this helpful? Thank you for your feedback!
-
1) Download and run the latest JBL Connect app on your phone 2) The JBL Connect app will begin discovering your JBL Boombox (please make sure your speaker is connected via Bluetooth first) 3) Use the toggle switch in the JBL Connect App to change the phone button to now have the voice assistant function 4) Simply press the “Play” button on your JBL Boombox (you will hear a brief tone) and begin speaking your commands via SIRI and Google Now. 5) Please check the below links for more information regarding SIRI and Google Now available voice commands: SIRI: https://support.apple.com/HT204389 Google Now: https://support.google.com/websearch/answer/2940021Was this helpful? Thank you for your feedback!
-
To answer and hang up calls, press the pause/play button located on the left arm of the Soundgear.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
