How To
How To
670 results
-
You can check on the JBL QuantumENGINE Spatial Sound page or check whether the Spatial Sound slider on top is onWas this helpful? Thank you for your feedback!
-
Select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your headphones' battery life appears in the top left corner. If you have an IOS device, you also will be able to see the battery life indicator in the upper right hand corner next to the BT symbol. Additionally, you should hear the audible voice stating ‘low battery’ when you have 15-20 minutes left of battery life left on the headphones.Was this helpful? Thank you for your feedback!
-
The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.Was this helpful? Thank you for your feedback!
-
Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.Was this helpful? Thank you for your feedback!
-
During phone call, short press the Siri Access button shown in “quick start guide” section 6 to mute the microphone. A short press the same button again will un-mute.Was this helpful? Thank you for your feedback!
-
Power on the Flip 3 SE and press the Bluetooth button. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tablet.Was this helpful? Thank you for your feedback!
-
Normal pairing is automatic, and happens when you first switch both devices on. If pairing does not take place automatically, or you have to force new pairing, here is what to do: Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly. Second, press the CONNECT button on the subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly. Third, press and hold the DIM DISPLAY button on the remote control for 5 seconds, followed by short press on BASS+, and BASS- button in sequence. Panel display will show “PAIRING”. If pairing succeeds, the LED indicator on the subwoofer lights up, and the soundbar display will show "DONE”. If pairing fails, the indicator on the subwoofer blinks slowly. Lastly, if the pairing fails, repeat the steps above. If you have continued trouble performing the pairing, please try to switch off all wireless devices in the home, then try again. This means routers, TV sets with wireless functions, telephones, computers etc. Since overcrowding on the 2.4 GHz frequency now often causes problems, eliminating all this activity makes space for the Bar to establish its connection, and you should be able to pair without problems. Afterwards, you can switch your devices on again. Often, all will now work fine, and if not, you will know which devices are doing the interference.Was this helpful? Thank you for your feedback!
-
On the Right ear cup, slide the bluetooth button towards the down position and hold until you see the fast blinking blue LED light. Make sure that the device that you are trying to connect to is in pairing mode. It should recognize the N60NC Wireless within a few seconds. You should here the audio "chime" when it is connected and the LED should change to a slow blinking light.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure the E65BTNC headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Press and hold the center button located on the inline microphone. It helps to have one or both ear inserts in the ear to hear the audio voice prompts. Once you press and hold the power button, you will hear the audio voice stating, "powering on". If this is your first time pairing the device, it will automatically go into pairing mode and will be looking for the device. Make sure the device you are trying to connect to is in search mode. It should recognize the Everest 110 within 2-3 seconds. If you would like to connect to a different device. Make sure the unit is off and proceed to press and hold the center button on the inline mic from 4-6 seconds until you hear "powering on......JBL Everest is ready to pair. Go to the pairing menu on your device" You will now be able to pair to a different device. The device should recognize the Everest 110 within 2-3 seconds and will connect.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Press the power button located on the far Left top of the speaker. If this is your first time pairing the device, the speaker will automatically go into pairing mode. Make sure that the product you are attempting to pair to is in search mode and in bluetooth range. The Go 2 should pop up on discoverable devices. Choose the Go 2 option and you will be connected within a few seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
