How To
How To
670 results
-
The owner's manual can be a bit difficult to understand. Here is what to do to program a preset station that has not already been saved in any preset: 1 Turn on the radio by clicking the FM button. 2 Find the station you want to save by doing what is shown under pt. 8 B or C, either clicking or pressing/holding for more than 2 seconds the left/right arrow buttons. 3 Press and hold the FM button for more than 2 seconds. Now the preset number appears blinking. 4 Click on the left/right arrow buttons to skip through the preset positions. 5 When you have located the desired memory preset position, such as Preset 4, confirm by clicking the FM button. Now the desired FM station is saved in memory preset 4. If you have already saved an FM station in a preset memory position, and want to have a new station placed there instead, here is what to do: 1 Turn on the radio by clicking the FM button. 2 Jump to the preset station you want to change with the round central button. Each click advances to the next preset. 3 When you are on the preset you want to change, e.g. preset 4, press and hold the FM button for more than 2 seconds. 4 The FM symbol and the frequency will now blink. 5 Before they stop blinking, click, or press and hold one of the arrow buttons to go through the FM frequencies step by step, or perform station search. 6 When you have found the new station you want to save in preset 4, click the round central button. 7 Now the new station is saved in preset 4.Was this helpful? Thank you for your feedback!
-
Press and hold the multi-function button shown in “quick start guide” section 5 to ignore incoming call.Was this helpful? Thank you for your feedback!
-
The best way is to carefully insert your nail in the groove where the two halves of the plug meet, then press into the groove until the two sections separate. If you pull on the cord, you may damage the cable by dislodging the cable from the plug.Was this helpful? Thank you for your feedback!
-
(1) Select the JBL soundbar you want to rename
(2) Navigate to the Support tile and select "Rename My Product."
(3) Press the current name and type in the new name
(4) Press SAVEWas this helpful? Thank you for your feedback! -
By pressing and holding the "Volume+" and "Handsfree" ( phone ) button together for 5 seconds. The Harman Kardon Aura Studio will power off, and is now reset back to factory defaults.Was this helpful? Thank you for your feedback!
-
Find a paper clip or something similar, then next to the power connection there is a small hole. Insert your paper clip and hold it until the Harman Kardon Allure tells you it is reset.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.Was this helpful? Thank you for your feedback!
-
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.Was this helpful? Thank you for your feedback!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.Was this helpful? Thank you for your feedback! -
While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.Was this helpful? Thank you for your feedback!
-
When less than one hour's capacity is left, the red diode will blink. It will eventually stop blinking, when all power is gone.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
