How to pair an Enchant Subwoofer with your Enchant bar

1. Go to the back of your Enchant soundbar (800 or 1300)
2. Press the "Subwoofer pairing" button for 2 seconds.

3. In front of your Enchant display, it will say "Subwoofer pairing"
4. Go to the back of your Enchant subwoofer.
5. Press the "Subwoofer pairing" button.

6. The small LED indicator will start to flash rapidly and when the connection is successful, it will be a steady light.

You now have more bass performance and can enjoy deeper richer sound!

1. Power on your Enchant 800 or Enchant 1300 Soundbar. 2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar. 2.1. Press the dedicated source button on top of your Enchant soundbar source 2.2. Press the source button until you see "Bluetooth" in the front of the Enchant display. 3. The second option is to use the Remote control included with your Enchant soundbar. 4. Press the "BT" button on your Remote control. 5. The display will show "Bluetooth pairing". 6. Go to your Bluetooth settings menu on your mobile device. 7. Enable Bluetooth and connect to your Enchant 800 or Enchant 1300 Soundbar.

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.

Prerequisites:
− Make sure that your room is quiet;
− Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
− Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.

The calibration is done in two steps: Listening zone & Speaker position

Calibrate the listening zone

1. Place the detachable rear speakers beside your seating position.

2. On the remote control, press and hold HDMI until “1-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “1-DONE”: Calibration of the listening zone is completed successfully.

Calibrate the speaker position

1. Place the detachable rear speakers in your desired location.

2. On the remote control, press and hold HDMI until “2-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “2-DONE”: Calibration of the speaker position is completed successfully.
3. To select suitable surround sound level, press repeatedly to switch between high, low or middle (default).

NOTES:
− During calibration, all buttons on the remote control are disabled except for STANDBY and HDMI.
− “SETUP FAILED” is displayed if calibration failed.

This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.

USB Stick

1. Get an empty stick with speed of 2.0.
2. Make sure it is formatted with FAT16 or FAT32.
3. Your Music files can only be:  (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
4. The Partybox supports up to 8 subfolders.
5. It will be played in alphabetic sequence with main folders first then subfolders.
6. To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.

Daily Care instructions for Citation speakers fabric (wool) Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years. Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself! Many types of stain can be removed using warm water with a microfiber cloth (not too wet). Stain removal guide If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains. Here is how to do it. First, soak up the liquid with an absorbent napkin or Microfiber cloth. For dried stains use a spoon to roughen the surface. To avoid the stain spreading further start from the edge of the stain working towards the middle. WARNING! Be careful when using solvents, because these could dissolve the upholstery material beneath. Regular and normal cleaning Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth. When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric). General information These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device. In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker. HARMAN do not have any recommended companies or partners to redirect any customers too. For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below: https://kvadrat.dk/care-and-maintenance/upholsteries https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf There are a lot of information about the fabric we are using and you can contact them for further information.

Daily Care instructions for Citation speakers fabric (wool)

Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years.
Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself!

Many types of stain can be removed using warm water with a microfiber cloth (not too wet).

Stain removal guide

If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains.
Here is how to do it.

1. First, soak up the liquid with an absorbent napkin or Microfiber cloth.
2. For dried stains use a spoon to roughen the surface.
   1. To avoid the stain spreading further start from the edge of the stain working towards the middle.
3. WARNING!
   1. Be careful when using solvents, because these could dissolve the upholstery material beneath.

Regular and normal cleaning

Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth.
When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric).
 

General information

These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device.
In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker.
HARMAN do not have any recommended companies or partners to redirect any customers too.

For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below:
https://kvadrat.dk/care-and-maintenance/upholsteries
https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf

There are a lot of information about the fabric we are using and you can contact them for further information.

(1) On the subwoofer's rear panel, press and hold the pairing button until the LED  turns fast, flashing white.
(2) To enter the subwoofer pairing mode on the soundbar, press and hold the bass button on the remote control for more than three seconds. Then, press VOL - on the remote control.

On the soundbar LED display:
→ "SUB PAIRING": The subwoofer is ready for pairing.
→ "SUB PAIRED": The subwoofer is connected.

To re-establish the functionality of the Advanced Swipe Controls (details in the image below), first update the My JBL Headphones app in the Google Play/App Store.
After the installation is completed, pair the earbuds to your phone/tablet through Bluetooth and open the app.
The earbuds will be detected and displayed in the app and you should see that a Firmware update is available.


Note: Advanced touch controls are deactivated by default, in the My JBL Headphones app go to Settings  once your earbuds are displayed, then select Gestures and enable Advanced Swipe Controls. You can now select each function and assign it to a specific gesture.

Resetting the Partybox to Factory Settings

1. Press and hold "Play" and "Light" buttons for > 10 seconds.
2. The Partybox will power off and back on and is now reset.

Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.