How To
How To
670 results
-
Your JBL speaker is waterproof with IPX7 rating. (IPX7 means it can survive immersion in 1 meter/3.3 feet for up to 30 minutes.) To maintain the looks and functions of your speaker, please make sure to rinse it with fresh water after using it at a swimming pool or the ocean, then dry off all covers and areas where water can gather. The standard for waterproofing is for tap water. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the surface finish over time if not rinsed off after use.Was this helpful? Thank you for your feedback!
-
Voice commands can only be triggered by the user who registered them during setup.Was this helpful? Thank you for your feedback!
-
With some phones, such as iPhones and some Android models, volume is synchronized while Bluetooth is used, and levels below volume setting 6 (tested with iPhone 6 and iPhone 5s) and volume setting 5 on most Android devices will cause the GO to enter standby after some minutes. If you want to play softer while still using your iPhone as a source, please change to cabled connection from the headphone output to the AUX input of GO. This will make it possible for you to set the GO's volume at its minimum step, and then control total level on the telephone. Of course, if source level from the telephone is set extremely low, the GO will go into standby again, because GO needs a certain level to keep playing. Alternatively, use a phone which does not synchronize volume as source. Many Android phones do not synchronize volume, so by using such a phone, you can adjust GO to its lowest level, adjusting total level independently, even via Bluetooth. This will usually result in music volume at the desired level.Was this helpful? Thank you for your feedback!
-
This headphone is supported by the My JBL Headphones App.Was this helpful? Thank you for your feedback!
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now.Was this helpful? Thank you for your feedback!
-
No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.Was this helpful? Thank you for your feedback!
-
Yes, this is normal for the N60NC BT. It disappears within about 20 seconds.Was this helpful? Thank you for your feedback!
-
If your Wi-Fi network name has special characters, such as (, `, \, ', ", or ), then please change the name of your Wi-Fi network, as these characters are not supported. After changing the name, you can go ahead and setup the speaker to your Wi-Fi network.Was this helpful? Thank you for your feedback!
-
Dual band routers that have 2.4 and 5 GHz connection bands. If devices connect on different bands, they cannot see one another. Please make sure your phone and speakers are both connected to 2.4 GHz or 5 GHz and that there is no AP isolation activated between them.Was this helpful? Thank you for your feedback!
-
One explanation can be that your OMNI 50+ is part of a 5.1 system with your Omni Bar, which will make the surround OMNI 50+ left and right rear speakers act as "secondary", and Bluetooth connection is not possible to secondary speakers. To use the OMNI 50+ as a portable speaker again, simply perform a reset of the speaker by pressing the reset button for 5 seconds. Please note that after resetting your OMNI 50+, it is no longer part of the 5.1 wireless system.Was this helpful? Thank you for your feedback!
-
It is normal because USB-PD (USB Power Delivering) fast charging has a higher charging speed at the beginning and lower when your device soon to be full.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
