How To
How To
670 results
-
The rechargeable AAA cells may of course be worn out, or they may not be installed at all. If this is the case, either insert the cells, or you can order new cells as original spare parts. Please contact Harman Helpdesk for your country, or the distributor for your country, for further info about how to buy new cells. Please note that the cells MUST be compatible with charging contact for the minus pole located on the side of the cell. Normal cells will not work. This is clearly mentioned in the owner's manual, and shown with a drawing. If you have purchased new cells with plastic coating along the length of the cell, it may be possible to peel off the coating by cutting gently with a knife, then peeling it off. Only about 1 cm needs to be open to the metal, closest to the flat end, for contact to be possible. Please note that the ear pads on K 912 are removed by simply grabbing the plastic plate that holds the ear pad, and pulling it away from the ear pod. There is one battery in each ear pod. For K 915, never just pull the pad away, since the locking claws are released by being rotated away from their locked position.. Both batteries are under the right-hand pad, and there is a silk-screened instruction on the top of the pod, showing that you must rotate the pad plate just a few mm counter-clockwise to unlock it.Was this helpful? Thank you for your feedback!
-
The wireless charge receiver in the smartphone may not be adequately coupled to the wireless charging transmitter on Smartbase. Re-adjust your smart phone’s position on the wireless charge arm.Was this helpful? Thank you for your feedback!
-
To set up the Harman Kardon Adapt in the HK Controller app, you have to select "One speaker", not the Adapt+ option. When selecting "One speaker", simply follow the on-screen instructions to install your Adapt on the Wi-Fi network. Note that the instructions for Adapt devices will appear on your screen after 30-45 seconds (Only Apple devices).Was this helpful? Thank you for your feedback!
-
Some vehicles don’t provide an isolated ground for the head unit which may introduce noise. Please connect your smartphone to JBL DRG and enable the “Aux Noise Cancel” button in the App. This can be found right after Aux Line option in Connection Mode section.Was this helpful? Thank you for your feedback!
-
Some head units in the vehicles use isolated grand, if JBL DRG use isolated grand as well, this will disable the chips inside DRG. Please connect your smartphone with JBL DRG and disable the “Aux Noise Cancel” button in the Apps right after Aux Line option in Connection Mode section.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Focus 700 is actually the Focus 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Inspire 700 is actually the Inspire 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
The InfinityLab power bank is not waterproof, if it gets wet, there's a chance for short-circuit, which can cause damage to other electronics that you plug into them. Ensure that you keep your power bank dry at all times.Was this helpful? Thank you for your feedback!
-
You can manually type in the network name (SSID) and password to connect if the network does not appear.Was this helpful? Thank you for your feedback!
-
NOTE: LINK speakers must be set up on a WiFi network before Bluetooth can be activated. Once it is set up, you can use Bluetooth anywhere (Unless you reset the speaker and start all over with installation).
Pairing issues with a Smartphone or Tablet:- First try to restart the Bluetooth connection on your source device (Smartphone/tablet) by switching Bluetooth off and on again with a short pause in between.
- Forget previous paired connection (on your smartphone/tablet) in your Bluetooth settings if you once had paired with our product.
- Try to restart source device(Smartphone/tablet) by powering it off and on again, and after restart try to establish a Bluetooth connection to your JBL LINK device.
- If above does not work, then try to restart your JBL LINK device by turning it off and on again.
- Press and hold down the Bluetooth button on your JBL LINK device to initiate pairing mode again.
- Go into Bluetooth settings on your Smartphone/tablet.
- Perform a restart or reset if you are not able to connect after above steps.
JBL LINK Bluetooth specifications:- Bluetooth version 4.2
- A2DP v1.3 with SBC Audio Codec.
- AVRCP v1.5
Was this helpful? Thank you for your feedback! -
At the bottom of your Horizon alarm clock, you will see a little cap where the backup-battery resides. Turn the cover lid left to open it, and on the back of the cover lid, you will see the serial number.Was this helpful? Thank you for your feedback!
-
In Amazon's app called Alexa. There you can set, change and login with your favorite supported music service. They offer Amazon Music, Spotify, Pandora and much more. Go to settings in the Alexa app, select "Music & Media.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
