How To
How To
670 results
-
For OMNI BAR+, three sources are available: HDMI (not applicable for ADAPT+), Optical or AUX input. For Adapt+ two sources are available: Optical in/outputs and Analog in/outputs. If you select "Watching movies and TV shows" in the HK controller app for either one of them, you will have a very little delay and good lip sync with the TV for video applications. However, you will not be able to rebroadcast the TV signal to other OMNI+ speakers when selecting this mode. If you select "Listening to music", you will be able to rebroadcast TV signal to other OMNI+ speakers in your house, however, you will have lip sync delay with video material. Select that specific mode if you use HDMI (not applicable for ADAPT+), Optical or AUX for music only. Using Chromecast, Spotify Connect or Bluetooth is not part of these modes. When using one of these streaming methods, you are able to rebroadcast any music source.Was this helpful? Thank you for your feedback!
-
The Harman Kardon Aura Studio 2 features: Bluetooth v.4.1 A2DP v.1.3 AVRCP v.1.5Was this helpful? Thank you for your feedback!
-
It is a tiny white sticker, located on the inside of the left-hand size adjustment slider on E35.Was this helpful? Thank you for your feedback!
-
The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.Was this helpful? Thank you for your feedback!
-
In Amazon's app called Alexa. There you can set, change and login with your favorite supported music service. They offer Amazon Music, Spotify, Pandora and much more. Go to settings in the Alexa app, select "Music & Media.Was this helpful? Thank you for your feedback!
-
At the bottom of your Horizon alarm clock, you will see a little cap where the backup-battery resides. Turn the cover lid left to open it, and on the back of the cover lid, you will see the serial number.Was this helpful? Thank you for your feedback!
-
NOTE: LINK speakers must be set up on a WiFi network before Bluetooth can be activated. Once it is set up, you can use Bluetooth anywhere (Unless you reset the speaker and start all over with installation).
Pairing issues with a Smartphone or Tablet:- First try to restart the Bluetooth connection on your source device (Smartphone/tablet) by switching Bluetooth off and on again with a short pause in between.
- Forget previous paired connection (on your smartphone/tablet) in your Bluetooth settings if you once had paired with our product.
- Try to restart source device(Smartphone/tablet) by powering it off and on again, and after restart try to establish a Bluetooth connection to your JBL LINK device.
- If above does not work, then try to restart your JBL LINK device by turning it off and on again.
- Press and hold down the Bluetooth button on your JBL LINK device to initiate pairing mode again.
- Go into Bluetooth settings on your Smartphone/tablet.
- Perform a restart or reset if you are not able to connect after above steps.
JBL LINK Bluetooth specifications:- Bluetooth version 4.2
- A2DP v1.3 with SBC Audio Codec.
- AVRCP v1.5
Was this helpful? Thank you for your feedback! -
You can manually type in the network name (SSID) and password to connect if the network does not appear.Was this helpful? Thank you for your feedback!
-
The InfinityLab power bank is not waterproof, if it gets wet, there's a chance for short-circuit, which can cause damage to other electronics that you plug into them. Ensure that you keep your power bank dry at all times.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Inspire 700 is actually the Inspire 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Focus 700 is actually the Focus 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
Some head units in the vehicles use isolated grand, if JBL DRG use isolated grand as well, this will disable the chips inside DRG. Please connect your smartphone with JBL DRG and disable the “Aux Noise Cancel” button in the Apps right after Aux Line option in Connection Mode section.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)