How To
How To
670 results
-
Press and hold the power button which is located on the right arm of the neck band. Press and hold for 3-5 seconds until you hear the audible voice state "Powering ON" followed by "Looking for device." Make sure the device you are attempting to connect to is in search mode and within bluetooth range. You will see Reflect Fit Audio on the discoverable devices. Choosing this option will allow you to receive audio playback.Was this helpful? Thank you for your feedback!
-
Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The DUET MINI headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.Was this helpful? Thank you for your feedback!
-
- Press the power button located on the top right of the speaker.
- If this is your first time pairing the device, the speaker will automatically go into pairing mode.
- Make sure that the product you are attempting to pair to is in search mode and in bluetooth range
- The Clip 3 should pop up on discoverable devices within a few seconds.
- Choose the Clip 3 option and you will be connected within a few seconds.
Was this helpful? Thank you for your feedback! -
To charge the Everest 110, slide the rubber window from the top down to expose the USB charging port that is located on the back of the inline microphone. Please use the JBL charging cable that was included in the packaging to charge these headphones.Was this helpful? Thank you for your feedback!
-
You can bend the ‘arms’ of the neck in and out to get the optimum fit for your exercise/level of activity. The flex zone is the black rubber part on the neckband.Was this helpful? Thank you for your feedback!
-
Download the HK Connect app to your mobile device. Make sure that the Onyx Studio 4 speaker is connected successfully to your mobile device. The HK Connect app should recognize the Onyx Studio 4 within the first few seconds. Once inside the app you can activate the voice assistant and connect to other Connect+ Harman Kardon devices.Was this helpful? Thank you for your feedback!
-
You will need to navigate to the System section, and if the software button is highlighted with "Download Software", please click on the button. When the download is completed, you can click "install update" to install latest version. Make sure you restart your computer once the upgrade is finished to ensure all changes are applied.Was this helpful? Thank you for your feedback!
-
You can go to the Control Panel> Programs and features to uninstall JBL QuantumENGINE.Was this helpful? Thank you for your feedback!
-
The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.Was this helpful? Thank you for your feedback!
-
Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.Was this helpful? Thank you for your feedback!
-
The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
When less than one hour's capacity is left, the red diode will blink. It will eventually stop blinking, when all power is gone.Was this helpful? Thank you for your feedback!
-
While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.Was this helpful? Thank you for your feedback!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.Was this helpful? Thank you for your feedback! -
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.Was this helpful? Thank you for your feedback!
-
Find a paper clip or something similar, then next to the power connection there is a small hole. Insert your paper clip and hold it until the Harman Kardon Allure tells you it is reset.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Handsfree" ( phone ) button together for 5 seconds. The Harman Kardon Aura Studio will power off, and is now reset back to factory defaults.Was this helpful? Thank you for your feedback!
-
(1) Select the JBL soundbar you want to rename
(2) Navigate to the Support tile and select "Rename My Product."
(3) Press the current name and type in the new name
(4) Press SAVEWas this helpful? Thank you for your feedback! -
The best way is to carefully insert your nail in the groove where the two halves of the plug meet, then press into the groove until the two sections separate. If you pull on the cord, you may damage the cable by dislodging the cable from the plug.Was this helpful? Thank you for your feedback!
-
Press and hold the multi-function button shown in “quick start guide” section 5 to ignore incoming call.Was this helpful? Thank you for your feedback!
-
The owner's manual can be a bit difficult to understand. Here is what to do to program a preset station that has not already been saved in any preset: 1 Turn on the radio by clicking the FM button. 2 Find the station you want to save by doing what is shown under pt. 8 B or C, either clicking or pressing/holding for more than 2 seconds the left/right arrow buttons. 3 Press and hold the FM button for more than 2 seconds. Now the preset number appears blinking. 4 Click on the left/right arrow buttons to skip through the preset positions. 5 When you have located the desired memory preset position, such as Preset 4, confirm by clicking the FM button. Now the desired FM station is saved in memory preset 4. If you have already saved an FM station in a preset memory position, and want to have a new station placed there instead, here is what to do: 1 Turn on the radio by clicking the FM button. 2 Jump to the preset station you want to change with the round central button. Each click advances to the next preset. 3 When you are on the preset you want to change, e.g. preset 4, press and hold the FM button for more than 2 seconds. 4 The FM symbol and the frequency will now blink. 5 Before they stop blinking, click, or press and hold one of the arrow buttons to go through the FM frequencies step by step, or perform station search. 6 When you have found the new station you want to save in preset 4, click the round central button. 7 Now the new station is saved in preset 4.Was this helpful? Thank you for your feedback!
-
Press the power button on the Flip 3 SE once to power on the device. When you power on the Flip 3 SE for the first time, it will automatically go into Bluetooth Pairing mode and you should be able to find the Flip 3 SE in the list of available Bluetooth devices on your mobile phone/tablet. Press the Bluetooth button on the Flip 3 SE to enable pairing mode manuallyWas this helpful? Thank you for your feedback!
-
Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The Tune 205BT headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.Was this helpful? Thank you for your feedback!
-
Press and hold the bluetooth button for 2-3 seconds. The bluetooth button is located on the bottom RIGHT ear cup. If this is your first time turning on the headphones, it should immediately begin to search for a device to connect to. You will see the blue LED light flash on the bluetooth symbol as it begins to search for the device. Make sure the bluetooth setting is on and in search mode on your device. The Soho Wireless should appear on your discoverable devices within 3-5 seconds. To power off, press and hold the bluetooth button until you hear the audio music prompt indicating that it has powered down.Was this helpful? Thank you for your feedback!
-
Make sure that the unit you are attempting to connect to is in pairing mode under Bluetooth Settings. Press the power button located on far right outer rim of the speaker. If this is the first time connecting the unit, it will immediately go into pairing mode. HK Onyx 4 Studio should show up on your discoverable devices within 3-5 seconds. Once you choose the HK Onyx Studio 4 on your device, you will be connected and ready to experience that superior Harman Kardon sound.Was this helpful? Thank you for your feedback!
-
Slide the power button in an upwards position. The power button will be located on the right arm next to the bluetooth button. Once you power on you will hear the audio chime. If this is your first time powering on the speaker, it will automatically go into pairing mode. You will see the fast blinking LED light as it searches for a device. Make sure that the device you are attempting to connect to is in pairing mode. The JBL Soundgear should be displayed on your discoverable devices within 3-8 seconds. Choose the JBL Soundgear and you are now connected!Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure the E65BTNC headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Press the power button located on the far Left top of the speaker. If this is your first time pairing the device, the speaker will automatically go into pairing mode. Make sure that the product you are attempting to pair to is in search mode and in bluetooth range. The Go 2 should pop up on discoverable devices. Choose the Go 2 option and you will be connected within a few seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
