How To
How To
670 results
-
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
Here is the pairing procedure between a K915 headset and a new transmitter box: 1. Power off the headphone. 2. Power off the transmitter. 3. Press and hold the power button on the headphone until the “Signal” LED is flashing, and a beep sound can be heard. 4. Power on the transmitter. 5. After a short while the “Signal” LED will light constantly (stop flashing) and the pairing is complete.Was this helpful? Thank you for your feedback!
-
Any changes you make on the Lighting page will be immediately reflected on your headset.Was this helpful? Thank you for your feedback!
-
The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Bluetooth" button together for 5 seconds. A voice will say the version number.Was this helpful? Thank you for your feedback!
-
The red diode that lights up when charging begins will go out again when charging is complete.Was this helpful? Thank you for your feedback!
-
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.Was this helpful? Thank you for your feedback!
-
The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.Was this helpful? Thank you for your feedback!
-
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.Was this helpful? Thank you for your feedback!
-
That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".Was this helpful? Thank you for your feedback!
-
Unfortunately, the JBL AmpUp App is no longer available for download.Was this helpful? Thank you for your feedback!
-
In the JBL ONE App:
(1) Go to My Products, select your product
(2) Select Support tile
(3) Under General, select Product SupportWas this helpful? Thank you for your feedback! -
Once the sound bar is connected to the network, software updates will automatically be sent to the speaker/soundbar through Wi-Fi or the internet, if availableWas this helpful? Thank you for your feedback!
-
You can delete specific voice recordings associated with your account by going to History in Settings in the Alexa App, drilling down for a specific entry, and then tapping the delete button. Or, you can delete all voice recordings associated with your account for your Harman Kardon Allure speaker, by selecting the applicable product at the Manage Your Content and Devices page at www.amazon.com/mycd. and deleting voice recordings. However, this may degrade your Alexa experience.Was this helpful? Thank you for your feedback!
-
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback! -
These headphones consist of plastics, synthetic leathers and foams. All JBL Jr products were put through extensive tests and are compliant with Standard Consumer Safety Specification for Toy Safety.Was this helpful? Thank you for your feedback!
-
HDMI Output
Both Enchant 800 and Enchant 1300 support these:- HDMI 2.0b compliance
- HDCP 2.2 compliance (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
- CEC features (Scroll to see support)
HDMI Input
Enchant features only 1 x HDMI input, and Enchant has 3 x HDMI inputs and support this:- HDMI 2.0b.
- HDCP 2.2 for all HDMI input connections (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
- 4K Pass-through.
CEC Support
CEC support only available through your HDMI connection and we are always using standard protocol for our products.
We support these:- System Standby: When you press the "Power off" button on your TV remote, the Enchant soundbar will go into Standby mode as well.
- ARC or called Audio Return Channel: If you would have a TV BOX connected directly to your TV and using ARC from TV to Enchant soundbar, then all sound will be transferred through ARC connection.
- In case you are not using the HDMI ARC connection then sound coming from the TV show will not be transferred to the Enchant soundbar.
- System Audio Control: Using your TV remote to turn up or lower the volume will be synchronized with the Enchant soundbar.
Bigger model is the Enchant 1300 and smaller model is the Enchant 800.Was this helpful? Thank you for your feedback! -
For JBL Quantum 100/200/300 models, they do not offer Game-Chat audio dial function.
To get the Game-Chat dial feature, you need JBL Quantum 400, and up, then you can adjust game-chat balance by rotating the dial-up and down.
For models that support Game-Chat dial, when you rotate the dial, you will feel a notch that indicates 50% game and 50% chat. Or you can see the status on the top bar of the JBL QuantumENGINE.Was this helpful? Thank you for your feedback! -
Horizon's alarm sounds for 3 minutes, then it shuts off, or rather it goes into snooze, for 9 minutes. Then it sounds the alarm again for 3 minutes, followed by snooze for another 9 minutes. After this final snooze period, it starts playing, and keeps on playing until it is manually shut off. The light shuts off with the audio.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Focus 500/700 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
Try all Flex Fit Ear fins included (S/M/L) to find a snug fit for stability during workout. Usually the biggest size that fits comfortably in your ear will provide the most stability. Try all ear tip sizes (S/M/L) to find a snug seal for optimum sound quality, and look for a balance of comfort and acoustic sealing.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
