How To
How To
670 results
-
To show the current firmware version on your JBL TUNER device, go through the following steps.
- Turn on the JBL TUNER.
- Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
- In the display, you will see a combination of letters and numbers. This is the current software version.
- See picture below as illustration.
The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.
Was this helpful? Thank you for your feedback! -
Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.Was this helpful? Thank you for your feedback!
-
Yes, you can adjust the game and chat audio balance by rotating the dial-up and down. When you rotate the dial, you'll feel a notch that indicates the balance is 50% game and 50% chat. The slider on Quantum ONE is different and has no notch but instead a visual indicator.Was this helpful? Thank you for your feedback!
-
1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).Was this helpful? Thank you for your feedback!
-
This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products
Was this helpful? Thank you for your feedback! -
Smart pass-through charging helps you boost your device and power bank simultaneously through one wall outlet.
Here is how it works:- Plug your power bank into a wall charger.
- Connect your device to the power bank (using the integrated cable or connecting a cable to it).
- Press the power button on the power bank to trigger charging if your phone/device doesn't indicate it is charging.
Was this helpful? Thank you for your feedback! -
Before you start
- Remove any interference that might be blocking the Soundbar side-firing speakers.
- Any ambient noise or sounds that could disrupt the calibration needs to be out of the room.
- In case you are moving the Enchant Soundbar you will need to calibrate the sound again.
- If something went wrong, you can always delete the calibration settings by resetting the system.
- Press and hold
button and
button down for 5 seconds.
- This will delete all settings, including the Wi-Fi connection.
- Press and hold
How to use the MultiBeam feature- Press and hold the CALIBRATION
button for 3 seconds.
- On the Enchant display a timer will start counting down from 3 to 0 (Once hitting 0 the Calibration will begin).
- The calibration takes around 60 seconds before it is complete. While calibrating you will hear some noises coming from the speaker.
- When finished the display on the Enchant Soundbar will say "DONE"
Was this helpful? Thank you for your feedback! -
It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone. Was this helpful? Thank you for your feedback! -
The power on/off symbol/button will flash white consistently. The LED switches to OFF when charging is complete.Was this helpful? Thank you for your feedback!
-
Make sure you disable AP/Client isolation on your Access Point / Extender and that Multicast forwarding is not disabled between the W-Fi networks. However, we cannot guarantee than streaming will work flawless as Extender networks are tricky and can cause many issues. Always use a 5GHz Wi-Fi network extender for best results.Was this helpful? Thank you for your feedback!
-
JBL DRG will auto reconnect to the last device. To setup a connection with new Bluetooth head unit, press the “reset” button in the App. The device will then search for a discoverable Bluetooth connection and setup.Was this helpful? Thank you for your feedback!
-
To use the Spotify Connect feature for JBL Playlist, a premium Spotify account is required. Please visit www.Spotify.com/freetrial for 30 days of complimentary premium account trial for first time users.Was this helpful? Thank you for your feedback!
-
Please keep the app running during a firmware upgrade. This is because the app is using BLE to transfer firmware to the JBL DRG. If you exit or kill the app, this will cause the BLE connection to be broken and the upgrade will not complete.Was this helpful? Thank you for your feedback!
-
If you are having problems playing music after setting up a new speaker (no matter what connection is used, Ethernet, Wi-Fi), please restart the Harman Kardon Controller app after the speaker setup is complete.Was this helpful? Thank you for your feedback!
-
It sounds like you are living in a country where Google Assistant has not yet been officially released. When Google releases the Google Assistant to more countries, the Everest GA headphones will open up for this feature. It may require a software update for this to happen. For now, you can use them as normal Bluetooth headphones and wait for the release to use the Google Assistant feature.Was this helpful? Thank you for your feedback!
-
Some third-party apps do not support volume changing when your smart device is in lock screen mode.Was this helpful? Thank you for your feedback!
-
If you are experience this message, please power cycle the Wi-Fi router and speaker(s). Disconnect the devices' power cable for 10 seconds and then reconnect them. Once the router and speaker(s) completely boots up, please try to setup again.Was this helpful? Thank you for your feedback!
-
This feature is not yet implemented in our Harman Kardon Allure or Allure portable speaker. Future updates might include this option, so we advise keeping an eye on the release notes in the HK Alexa Setup app about possible future firmware updates.Was this helpful? Thank you for your feedback!
-
The Harman Kardon Aura Studio 2 only supports Bluetooth. The HK Controller app only works with Harman Kardon products that have WiFi connectivity.Was this helpful? Thank you for your feedback!
-
Please note that two types of ear tips are included with AKG N5005. The black ones are normal silicone tips, and they are fine for many users. The Milky-white ones are from the company SpinFit. They have a special middle section that permits the tip to swivel in all directions, making them able to adapt to various insertion angles. Please try both. For some, one is better, for some, the other one is better. You make the decision. In normal use, the tip that makes the best seal with your ear canal is the best choice, since bass reproduction is very dependent on this seal. However, some users may find that they prefer a slightly less tight seal.Was this helpful? Thank you for your feedback!
-
Unfortunately, some Huawei phones are not able to stream music from the HK Controller app to 1st generation Omni speakers. However, the new Omni 10+, 20+, and 50+ have fixed this issue, and you will be able to stream music to them using your Huawei phone.Was this helpful? Thank you for your feedback!
-
It is not possible to use the speaker while installing it to your WiFi network. Once you have successfully connected to the WiFi network, you can use Bluetooth and AUX again.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The JBL Free will automatically switch to mono mode on the RIGHT ear when the call starts. After the call ends stereo music mode will automatically resume.Was this helpful? Thank you for your feedback!
-
The registration success rate and quality of voice commands depends on the performance of your smart phone’s microphone. Make sure that your smart phone’s microphone is unobstructed and you are speaking clearly when registering commands. If you continue to have issues, try registering using a family member or friend’s smart phone as a test. If voice command registration is successful with their device, the microphone on your smart phone may have issues.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
