How To
How To
671 results
-
No, this feature is not supported in our Harman Kardon Allure speaker. This might change with future updates. You can call your Amazon friends by using the Alexa app.Was this helpful? Thank you for your feedback!
-
Yes, these headphones can be connected and paired to two devices at the same time.Was this helpful? Thank you for your feedback!
-
Yes. Out-the-box the JBL Bar series soundbar recognizes volume and mute controls from the most common TV remote controls. The JBL Bar series has IR learning. You can use this feature to teach the soundbar to response to your TV's remote control as well.Was this helpful? Thank you for your feedback!
-
Yes, the smooth leather headband from the K601 can be fitted onto the K701, but since it is probably no longer available as a spare part, the only option is to butcher an old 601 to do it. The work involved is very intricate and complicated, and paying a technician to do it is not an economical solution. Owner must be capable of completely dismantling the headphones, including soldering, and to reassemble them. And Harman cannot offer any assistance in doing this. As of late 2017, a new version of K701 is being marketed by AKG Professional. This version features a smooth headband instead of the version with bumps, so the issue no longer applies.Was this helpful? Thank you for your feedback!
-
It is possible to replace the ear pads, but there are details to consider. On Elite 700: The ear pads are held in place by a plastic plate with claws, and some of the claws will most likely break off when you remove the pad. You do this by grabbing under the edge where the fabric ends, then pulling hard outward. The claws will eventually let go, and some of them will break off, rattling inside the ear pod. The only way to get them out is to unscrew the speaker plate, lift it up, and shake out the broken-off claws. The new pads are simply centered over the speaker plate, and the claws pressed into the holes with a firm pressure. On Everest 700: The ear pads are glued into position with double-adhesive tape. Pull the old pads off with a forceful, steady pull, until the glue lets go. Remove the protective layer on the new pads, and carefully position them correctly before pressing home all the way around the edge.Was this helpful? Thank you for your feedback!
-
Yes, you can see all voice interactions with the Harman Kardon Allure by using the Alexa app and visiting History in Settings. Your interactions are grouped by question or request. Tap an entry to see more detail, provide feedback, or listen to audio sent to the Cloud for that entry by tapping the play icon. Sometimes Alexa may not understand you perfectly, and the translations you see in History may not always reflect exactly what you said (for example, they may be inaccurate or incomplete). You can help us improve your experience by providing feedback on inaccurate translations in History.Was this helpful? Thank you for your feedback!
-
You can only share the sound via JBL Connect through Bluetooth connected devices. TV sound is not permitted as it would cause lip-sync issues.Was this helpful? Thank you for your feedback!
-
Yes, Control Xstream is a Chromecast device that allows you to cast music content via your Chrome browser. However, the JBL Control Xstream is not made for video purposes, because there will be delay between sound and image.Was this helpful? Thank you for your feedback!
-
Yes, you can take can incoming call from the Onyx 4 by pressing the call button located between the power button and volume + button.Was this helpful? Thank you for your feedback!
-
Yes, the JBL Duet Mini features a three button microphone which enables you to pause/play, skip tracks and answer and hang up phone calls.Was this helpful? Thank you for your feedback!
-
Yes. Go into our HK Alexa Setup app, tap on the 3 line icon and click on "Lightning" to toggle it on and off.Was this helpful? Thank you for your feedback!
-
Yes, When an update is available, you will find this on the product website of the Harman Kardon Aura Studio 2, in Manuals and Downloads. You will need to connect your Harman Kardon Aura Studio 2 by USB, and run the software update from a compatible computer.Was this helpful? Thank you for your feedback!
-
Yes, from within the JBL Connect App, when you have 2 JBL Boombox speakers connected, set them in Stereo Mode. When you add a 3rd ( or more ) JBL Boombox speakers, they will automatically revert back to Party modeWas this helpful? Thank you for your feedback!
-
Yes, the remote control permits you to pick up and stop a call, and activate the voice assistant to place a call.Was this helpful? Thank you for your feedback!
-
No, the Allure speaker requires an internet connection in order to use Alexa voice commands. You can always listen to music via the Bluetooth connection if you are out of range with your Wi-Fi networkWas this helpful? Thank you for your feedback!
-
No, stereo pairs must be two of the same type of speaker. For example, two Omni 10 or two Omni 10+ speakers will work, but not one Omni 10 and one Omni 10+.Was this helpful? Thank you for your feedback!
-
Yes, that’s the best part about this speaker, there are so many options. Besides streaming over Wi-Fi, the JBL Control Xstream also offers a Bluetooth connection and an AUX inputWas this helpful? Thank you for your feedback!
-
No, When connected from multiple mobile devices ( up to 3 ) to one Harman Dual Sound enabled speaker, only the last one that connected will stay connected when enabling Harman Dual Sound. You can however connect from one mobile device to one of the 2 Harman Dual Sound enabled speakers, and activate Dual Sound afterwards. This will give you the option to interrupt the playback, in the same way as Social Mode works when connected to only one speaker.Was this helpful? Thank you for your feedback!
-
No, each headset must have its own transmitter. However, even if you try to use more than one complete set of 915 in the same room simultaneously, it may not work either. Although the 915 has an automatic scan function that finds available slots in the 2.4 gHz transmission frequency band, interference may still occur.Was this helpful? Thank you for your feedback!
-
Yes, you can use the headphones, but of course the noise cancelling will not be active.Was this helpful? Thank you for your feedback!
-
Yes, you do not need to have music playing to keep the noise cancelling switched on. There may be a slight residual hiss from the NC system, which would usually be masked by music, but there will still be a significant reduction of external noise.Was this helpful? Thank you for your feedback!
-
Streaming via Bluetooth or direct aux in connection are supported without the HK Controller app. For OMNI+ devices that you already have placed in a room, they are capable of using either Spotify Connect or Chromecast built-in without the need of using the HK Controller app. Use only the HK Controller app for setting up any OMNI+ devices you may have.Was this helpful? Thank you for your feedback!
-
Yes, you can activate the noise reduction circuits alone, with no connection to a source device by Bluetooth or cable. The headphones will stay on as long as there is power in the battery, which is close to 30 hours for pure NC function. Please note that there is a slight residual noise from the NC system, which will be drowned out by music playing, or by surrounding noise such as airplane noise. If you use the NC in surroundings that are near quiet to begin with, you may not get an improvement in noise level.Was this helpful? Thank you for your feedback!
-
Yes, but only with music via cable, and noise reduction will not be active. As soon as you insert the charging cable micro-usb plug, the Bluetooth and NC functionalities will be switched off, and they cannot be reactivated unless you remove the charging cable, and there must of course be a charge in the battery. If you listen to cabled music while charging, be prepared to hear noise under certain conditions. Both computers and switch-mode power supplies can be very noisy, and this noise can sometimes be heard as a whine or buzz. This can only be eliminated by using a power supply that does not create noise.Was this helpful? Thank you for your feedback!
-
Yes, in case your Wi-Fi does not work then simply press and hold the Bluetooth button for 3 seconds, your speaker is now in pairing mode. The button is located on the back where you connect the power cord. Please be aware that Alexa will not work on Bluetooth.Was this helpful? Thank you for your feedback!
-
No. The only way that the Noise Cancellation feature can be activated is while you are using the headphones wirelessly. You cannot use NC while the headphones are plugged into a device or charging.Was this helpful? Thank you for your feedback!
-
The JBL Quantum 800 can only be used via a 3.5mm, Bluetooth, or 2.4Ghz wireless connection.Was this helpful? Thank you for your feedback!
-
There is a buffer inside the speakers that processes the incoming signal. This buffer delays the audio signal compared to the video signal, causing a delay. For this, we do not recommend using Omni+ speakers with a TV. Our Omni bar will work with your TV sound and you can create wireless 5.1 surround sound system with the Omni bar.Was this helpful? Thank you for your feedback!
-
Yes, however, the JBL ONE App gives you another level of control over the soundbar.
Through the App, you can personalize the soundbar's performance, such as:- Customizing EQ settings
- Setting up our new feature called: My Moment
- Connect your favorite streaming music services.
Was this helpful? Thank you for your feedback! -
Yes, all sources that output analog stereo line-level signals or stereo audio optical digital signals may be used, cable-connected to the BTA 20 transmitter. Digital signals must be in PCM format. So if you have a CD player or an FM radio, you can connect the BTA 20 to it, and transmit to your Soundgear (or to other Bluetooth headphones that support the format). Please note that record players need an additional preamplifier to work this way. Of course a TV set can be connected as well, either via optical digital PCM output, via line outputs or via headphone output.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
