How To

Support Overview / How To

How To

670 results
  • What router should i get, to have the best performance for my OMNI+ system?
    To have the best possible performance for OMNI+ system we advise to have a dual-band router with a powerful chipset and ram for best Wi-Fi performance. This will not only help our products to perform better and more stable, but your other devices at home will have more power and fewer interruptions. Please also be sure that your home Wi-Fi router has Multicast enabled, as our Omni+ system requires this feature enabled in order to work (same goes for Chromecast devices). Always connect our Omni+ system to 5 GHz Wi-Fi whenever possible to limit the risk of devices being slow or interrupted on 2.4GHz Wi-Fi.
  • What settings should I use to get the most out of JBL QuantumSURROUND?
    Different games have different settings, but as a general rule, make sure that your game outputs multi-channel unprocessed audio. We recommend 7.1 surround, but 5.1 works too. Always disable any other processing (like DTS and Dolby).  
  • What should I expect after turning on JBL QuantumSURROUND?
    The first thing you’ll notice is that sound no longer feels like it’s “inside your head.” Suddenly it seems like the game audio is coming from high-quality loudspeakers—or the virtual game world—all around you.

    It’s a different experience than you get with other headphones, and may take a little while to adjust to. For example, sounds coming from sources in the distance will seem farther away, as they would in real life. Even though you might be used to those sounds feeling closer with other headphones, JBL QuantumSURROUND provides hyper-accurate spatialization that can give you a competitive edge.

    So spend some time dialing in the EQ to your liking, and see how real-world hearing helps you pinpoint enemies and bring the game to life. 
     
  • What to do when your InfinityLab power bank is warm while charging other devices
    Normally, the InfinityLab power bank may be warm to the touch during discharging.  
    However, if the power bank becomes too hot, starts to expand, or emits a strong odor, please stop using it immediately and contact our customer service. 
  • What type of connectors are used on the AKG K550 MKIII?
    The connector between headphones and cable is Mini-XLR with lock mechanism. The connector that goes into sources is a combination plug, 3.5mm jack with 6.3mm adapter.
  • What you need to get started with your device

    Getting started with the checklist

    • A JBL LINK device(s).
    • Latest version of the Google Home appGoogle Home app installed on your mobile device.
    • Latest version of the Google app  (Android only) installed on your mobile device.
    • A Google Account (you can create one online via Google).
    • A mobile device with either iOS or Android support.
      • ​Must have iOS 10 or higher
      • Must have Android 5.0 and higher
      • There is no support for PC set up.
    • An internet connection from your local ISP (Internet Service Provider).
    • Your Wireless Network must secured with WPA2 Encryption (Enterprise mode NOT supported). 
    • Availability and performance of certain features, services and applications are device- and network-dependent and may not be available in all areas; subscription(s) may be required, and additional terms, conditions and/or charges may apply.

    Wi-Fi requirement

    • Wi-Fi routers must have Encryption enabled to install JBL LINK speakers (WPA2 etc).
    • Wi-Fi Extenders need to feature support of Multicast forwarding and UPnP.
    • Always use 5 GHz Wi-Fi for best performance and less interference.
    • For routers that have 2.4G Wi-Fi support only, make sure that they are using channels 1, 6 or 11 only.
    You can now install your JBL LINK speaker to your Wireless Network and you can find our setup article that shows how to install your LINK product.

     
  • What’s the difference between JBL QuantumSURROUND and JBL QuantumSPHERE 360?
    JBL QuantumSPHERE 360 is JBL QuantumSURROUND that’s kicked up a notch by using a head-tracking sensor to fix sounds in 360 degrees of space around you. With typical headphones, when you move your head, the soundscape follows your movement. But with JBL QuantumSPHERE 360, if you rotate your head, the sound source’s perceived location stays in place because the head-tracking sensor compensates for your head movement. For example, if there’s a sound coming from in front of you, and you turn your head to the left, the sound source’s perceived location moves to your right ear—the sound stays locked in space as you move your head. 

    Also, the human brain uses small head movements to distinguish if sound sources are behind or in front of us. The brain processes the differences between when a sound arrives at the left vs. the right ear to determine where the sound is located. So with JBL QuantumSPHERE 360, you can move your head naturally to pinpoint the exact source of sounds around you. 
  • When I connect JBL DRG with my head unit via Bluetooth, the audio stream will be interrupted and I can hear “papapa…” noise when play music.
    • Please check whether your head unit Bluetooth support EDR (Enhanced Data Rate) • If the head unit does not support EDR this will cause the transfer data rate to be low and will impact the audio quality.
  • When I connect my JBL speaker with a computer (PC/Laptop/Apple Mac/Nintendo Switch), can I use the PartyBoost feature?
    The PartyBoost feature is not available when your JBL speaker is connected to a computer via Bluetooth. This is a technical limitation. When connected to a computer, the computer is acting as the primary device. Therefore, the JBL speaker does not have control of re-transmitting the Bluetooth signal to other JBL speakers.

    NOTE: Speakers effected by this are the JBL Flip 5, JBL Flip 6, JBL Charge 5, JBL Pulse 4, JBL Xtreme 3, and JBL Boombox 2, as well as all future products featuring the PartyBoost feature.
  • When I dock my K 912 or K 915 headphones in the charging station/transmitter, the CHARGE light does not come on, and no charging takes place.
    The rechargeable AAA cells may of course be worn out, or they may not be installed at all. If this is the case, either insert the cells, or you can order new cells as original spare parts. Please contact Harman Helpdesk for your country, or the distributor for your country, for further info about how to buy new cells. Please note that the cells MUST be compatible with charging contact for the minus pole located on the side of the cell. Normal cells will not work. This is clearly mentioned in the owner's manual, and shown with a drawing. If you have purchased new cells with plastic coating along the length of the cell, it may be possible to peel off the coating by cutting gently with a knife, then peeling it off. Only about 1 cm needs to be open to the metal, closest to the flat end, for contact to be possible. Please note that the ear pads on K 912 are removed by simply grabbing the plastic plate that holds the ear pad, and pulling it away from the ear pod. There is one battery in each ear pod. For K 915, never just pull the pad away, since the locking claws are released by being rotated away from their locked position.. Both batteries are under the right-hand pad, and there is a silk-screened instruction on the top of the pod, showing that you must rotate the pad plate just a few mm counter-clockwise to unlock it.
  • When I put smart phone on the Smartbase wireless charge arm, it doesn’t charge.
    The wireless charge receiver in the smartphone may not be adequately coupled to the wireless charging transmitter on Smartbase. Re-adjust your smart phone’s position on the wireless charge arm.
  • When I select Adapt+ in the HK Controller app, I am not able to set up my older Adapt. How come?
    To set up the Harman Kardon Adapt in the HK Controller app, you have to select "One speaker", not the Adapt+ option. When selecting "One speaker", simply follow the on-screen instructions to install your Adapt on the Wi-Fi network. Note that the instructions for Adapt devices will appear on your screen after 30-45 seconds (Only Apple devices).
  • When I transfer the audio from JBL DRG to my head unit via AUX, I can hear noise from the speakers.
    Some vehicles don’t provide an isolated ground for the head unit which may introduce noise. Please connect your smartphone to JBL DRG and enable the “Aux Noise Cancel” button in the App. This can be found right after Aux Line option in Connection Mode section.
  • When I transfer the audio from JBL DRG to my head unit via AUX, I can’t hear anything.
    Some head units in the vehicles use isolated grand, if JBL DRG use isolated grand as well, this will disable the chips inside DRG. Please connect your smartphone with JBL DRG and disable the “Aux Noise Cancel” button in the Apps right after Aux Line option in Connection Mode section.
  • When I try to pair my Focus 700 to my device, the Focus 500 is displayed on my discoverable devices. Is this normal?
    What you are experiencing is normal. The Focus 700 is actually the Focus 500 headphone but with the added bonus of a charging case.
  • When I try to pair my Inspire 700 to my device, the Inspire 500 is displayed on my discoverable devices. Is this normal?
    What you are experiencing is normal. The Inspire 700 is actually the Inspire 500 headphone but with the added bonus of a charging case.
  • When the Power bank is wet, what to do?
    The InfinityLab power bank is not waterproof, if it gets wet, there's a chance for short-circuit, which can cause damage to other electronics that you plug into them. Ensure that you keep your power bank dry at all times.
  • When using the JBL One app to set up my speaker, my Wi-Fi network is not appearing in the list. How can I connect to my Wi-Fi network?
    You can manually type in the network name (SSID) and password to connect if the network does not appear.
  • When you experience Bluetooth issues.
    NOTE:  LINK speakers must be set up on a WiFi network before Bluetooth can be activated. Once it is set up, you can use Bluetooth anywhere (Unless you reset the speaker and start all over with installation).

    Pairing issues with a Smartphone or Tablet:
    1. First try to restart the Bluetooth connection on your source device (Smartphone/tablet) by switching Bluetooth off and on again with a short pause in between.
    2. Forget previous paired connection (on your smartphone/tablet) in your Bluetooth settings if you once had paired with our product.
    3. Try to restart source device(Smartphone/tablet) by powering it off and on again, and after restart try to establish a Bluetooth connection to your JBL LINK device.
    4. If above does not work, then try to restart your JBL LINK device by turning it off and on again.
    5. Press and hold down the Bluetooth button on your JBL LINK device to initiate pairing mode again.
    6. Go into Bluetooth settings on your Smartphone/tablet.
    7. Perform a restart or reset if you are not able to connect after above steps.
    Back to helpful articles --> Articles overview

    JBL LINK Bluetooth specifications:
    • Bluetooth version 4.2
    • A2DP v1.3 with SBC Audio Codec.
    • AVRCP v1.5
  • Where can i find the serial number for Horizon alarm clock?
    At the bottom of your Horizon alarm clock, you will see a little cap where the backup-battery resides. Turn the cover lid left to open it, and on the back of the cover lid, you will see the serial number.
  • Where can I set my default music provider for my Harman Kardon Allure?
    In Amazon's app called Alexa. There you can set, change and login with your favorite supported music service. They offer Amazon Music, Spotify, Pandora and much more. Go to settings in the Alexa app, select "Music & Media.
  • Where is the Heart Rate sensor on the JBL Reflect Fit?
    The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.
  • Where is the serial number on JBL E35?
    It is a tiny white sticker, located on the inside of the left-hand size adjustment slider on E35.
  • Which Bluetooth version does the Aura Studio 2 have?
    The Harman Kardon Aura Studio 2 features: Bluetooth v.4.1 A2DP v.1.3 AVRCP v.1.5
< 1 ... 23 24 25 26 27 28 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a product expert
Call us now at: +6129 151 0376

Mon-Fri 8:00 AM to 5:00 PM (AEST)

E-mail Us

E-mail Us

365 days a year

We will respond within one business day.

Email Us
Chat with Us

Chat with Us

Mon-Fri 8:00 AM to 5:00 PM (AEST)

message