JBL PartyBox 1000
Powerful Bluetooth party speaker with full panel light effects
Sold from 2019 until now
Documents & Downloads
Product Specifications
- Output power (W)
- 1100
- Dynamic frequency response range (Hz)
- 30Hz-20kHz (-6dB)
- Dimensions (cm)
- 39.7 x 39 x 105
- Dimensions (in)
- 15.6 x 15.3 x 43.3
- Weight (kgs)
- 34.7
- Weight (lbs)
- 76.5
- Wireless Connectivity
- Bluetooth Technology
- Air Gesture Wristband using BLE technology
- 3.5 mm audio cable Input
- Yes
- Auto-power off
- Yes
- Bluetooth
- Yes
- Karaoke function
- Yes
- Lightshow
- Yes
- Wireless
- Yes
- Note
- The product is in compliance with the European Union energy legislation. 1) Bluetooth connection mode - The product is intended to be used for streaming music via Bluetooth connection. A consumer can stream Bluetooth audio to the speaker. When the product is connected through Bluetooth, the Bluetooth connection must remain active at all times to ensure proper operation. The product will enter into sleep mode (networked standby), after 20 minutes without operation, the power consumption @ sleep is less than 2.0 Watts, after which it can be re-activated via Bluetooth connection. 2) Bluetooth disconnection mode - The product will enter into standby mode, after 20 minutes without operation, the power consumption @ standby is less than 0.5 Watts.
- Note
- WARNING!! This product contains a button/coin cell battery and is hazardous. Keep batteries away from children. Batteries can cause severe or fatal injuries in 2 hours or less if swallowed or placed inside any part of the body. Medical attention should be sought immediately if it is suspected the battery has been swallowed or placed inside any part of the body.
The Ultimate Party Machine!
The JBL PartyBox 1000 is a powerful party speaker with JBL sound quality and exciting full panel light show. Just plug in your Mic or Guitar and take the stage or stream your playlist via Bluetooth or from a USB stick. The LED lit DJ and Party Band bring concert to your party! Connect two PartyBox speakers wirelessly with the TWS feature or wired from one RCA output to another RCA input. Let's get the party started!
JBL offers unprecedented performance and authentic audio experiences you will remember for your party!
The full panel lighting effect create a captivating light show to astound your crowd with a lasting visual experience.
Air gesture wristband brings everyone together!
This DJ Pad allows you to play drums, guitar and piano, record and loop on the fly!
Plug in your mic or guitar and take the stage.
Pre-program your party or event with your favorite playlist from a USB thumb drive!
Connect compatible speakers wirelelessly via TWS (True Wireless Stereo using Bluetooth connection up to 2 party speakers) or wired via one RCA output to another.
A USB port on the JBL PartyBox lets you charge other USB devices right from the
speaker. So you don’t need an extra charger to keep your devices powered up.
A handle and concealed wheels make it easier to transport your JBL PartyBox 1000
FAQs & How-Tos
11 results
-
It is very simple to connect to your Car with the JBL Partybox 200 or 300. Use the included cable that connects through the cigarette connector in your Car and power on the Partybox! Please note that the 12V connection does not charge the battery in the Partybox 300 - it will only power the Partybox when in use. To charge the battery, it will have to be plugged into AC power ( 110 - 230V )Was this helpful? Thank you for your feedback!
-
Demo mode
- Press the Play and Boost button at the same time for 5 seconds.
- Depending on what state your JBL Partybox is in, either you enter Demo mode or disabling it.
- NOTE: In Demo mode, you cannot use the JBL Partybox as most features and buttons are not working.
Was this helpful? Thank you for your feedback! -
Bluetooth Pairing
- Press the
button on the Partybox to start the pairing process.
- Grab your
device.
- Go to settings --> Bluetooth --> Enable Bluetooth -->
- Find the Partybox speaker you want to establish a Bluetooth connection to.
- You now have a successful connection and can stream your favorite music.
- NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
- To stop Bluetooth broadcasting then insert a USB device.
Was this helpful? Thank you for your feedback! - Press the
-
Finding the software version
- Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
- A voice will start prompting numbers which indicates the current software version.
Was this helpful? Thank you for your feedback! -
USB Stick
- Get an empty
stick with speed of 2.0.
- Make sure it is formatted with FAT16 or FAT32.
- Your Music files can only be:
(32-320kbit/s),
(32-320kbit/s) and
(44.1K/48K/192K).
- The Partybox supports up to 8 subfolders.
- It will be played in alphabetic sequence with main folders first then subfolders.
- To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.
Was this helpful? Thank you for your feedback! - Get an empty
-
Resetting the Partybox to Factory Settings
- Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
- The JBL Partybox will power off and back on and is now reset.
Was this helpful? Thank you for your feedback! -
This model is not supported by the JBL Partybox App.Was this helpful? Thank you for your feedback!
-
It is possible to pair two of the same model of JBL PartyBox speakers together through TWS (True Wireless Stereo) mode.
PartyBox On-The-Go/100:
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).
PartyBox 200/300/1000:
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.
Partybox 110/310/710/Encore/Essential:
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).
TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.
Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 and PartyBox 300 which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the Partybox 110, 310, 710 or Encore/Essential together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.Was this helpful? Thank you for your feedback! -
You can have your own Karaoke party with your JBL Partybox. Simply connect your Microphone (only included with the Partybox On The Go) and connect your mobile device over Bluetooth, then start playing music and sing along, it is that simple!Was this helpful? Thank you for your feedback!
-
You can connect two of the same Partybox models (e.g. 2 x Partybox 310, or 2 x Partybox 100) together in TWS Mode by pressing and holding the Bluetooth button on both speakers for 5 seconds, or by pressing the dedicated TWS buttons on the rear panels of both speakers on the Partybox 110, 310 and 710. It is possible to pair two different Partybox models together using a wired connection (e.g. 1 x Partybox 310 and 1 x Partybox 100). It is also possible to pair two Partybox different models wirelessly in Party mode, however this is only possible with the newer Partybox models - the Partybox 110, 310 and 710. The Partybox 200 & 300 can be paired in TWS mode as they are the same model apart from the presence of a battery in the Partybox 300. If you connect an instrument or microphone to one Partybox speaker while using TWS, the instrument or microphone connected to one speaker will be reproduced by this speaker alone. You will not hear the instrument or microphone in both speakers. If it is necessary to have instruments reproduced by two or more PartyBox speakers, it is possible to use an RCA or aux cable – connected from the RCA, aux or daisy chain outputs on the speaker that the instrument or microphone is connected to, wired to the RCA, aux or daisy chain input of the secondary speaker. Alternatively a small mixing console can be used - connecting audio sources to this mixer and sending the mixed audio signal to the speakers with a wired connection.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Chat with Us
Mon-Fri 8:00 AM to 5:00 PM (AEST)
