B110

B110

1000-watt 10" Powered Subwoofer

Downloads

Product Specificaties

Height
17" (43.2 cm)
Width
14.2" (36.2 cm)
Depth
With grille
Weight
Net Weight
Features
DSP EQ
Finishes
Piano Black, Piano White or High Gloss Walnut
Input Connections
Line-level XLR and RCA In/Out
Amplifier Power
1000W
Drive Components
10" Coated paper/pulp cone with 50mm two-layer copper voice coil, vented triple-stacked ceramic 5 magnet assembly and vented die-cast aluminum frame
Height
17" (43.2 cm)
Width
14.2" (36.2 cm)
Depth
With grille
Weight
Net Weight
Features
DSP EQ
Finishes
Piano Black, Piano White or High Gloss Walnut
Input Connections
Line-level XLR and RCA In/Out
Amplifier Power
1000W
Drive Components
10" Coated paper/pulp cone with 50mm two-layer copper voice coil, vented triple-stacked ceramic 5 magnet assembly and vented die-cast aluminum frame

B110

This new unit maintains a precise engineering balance between the voice coil, spider and surround that produces linear motion of all three for lower distortion by incorporating CAD/FEA optimized high-linearity motor geometry. The extremely long (50mm) two-layer copper voice coil gives this transducer a very high Xmax, dramatically increasing output. A fiberglass voice coil former helps the voice coil withstand high temperatures, reducing power compression and helping increase output. A cardboard spacer added at the top of the voice coil former maintains motor geometry, creates a solid attachment joint and prevents deformation of the voice coil at high outputs. The spacer also eliminates the typical single fulcrum point between the spider and cone on the voice coil former, minimizing voice coil rocking modes during hi-power operation. A high-temperature nomex spider features a progressive roll design that evenly distributes mechanical stress, helping keep the cone’s motion linear during high excursion operation. A nitril/butylene rubber surround uses patented Plus One® technology that increases the transducer’s radiating area (Sd), increasing volume displacement and output. The coated cellulose/pulp cone and dustcap assembly is vented under the dustcap to aid in the exchange of air, which reduces acoustic losses and increases output. The transducer’s magnet assembly features a triple-stacked vented ceramic 5 magnet with flared vents that reduce turbulence, which improves airflow, increases output and reduces distortion. Dual symmetrical magnet shorting rings and an extended top pole create a symmetrical magnetic gap field that increases power handling and reduces power compression further increasing output. A 15mm-thick top plate improves heat and flux distribution for lower distortion. The cast aluminum frame is fully vented to minimize acoustic losses caused by excessive back pressure. This frame also maintains dimensional stability and precise mechanical tolerances, allowing the transducer to be manufactured and assembled to a high degree of precision.

Kan je niet vinden wat je zoekt?

Bel onze support-afdeling

Bel onze support-afdeling

Bel ons nu op: +32 (0) 28080136

Maandag - Vrijdag: 09.00-18.00
Zaterdag - Zondag: 10:00-16:00

Stuur een email aan onze support-afdeling

Stuur een email aan onze support-afdeling

We zijn er van maandag t/m zondag om je vragen zo snel mogelijk te beantwoorden!

Stuur ons een email
Chat met onze support-afdeling

Chat met onze support-afdeling

Chat is open op werkdagen tussen 09:00 en 18:00 en van 10:00 - 16:00 in het weekend.

message

WhatsApp Ons

Stuur ons een bericht hier 

Maandag - vrijdag: 09.00-18.00
Zaterdag - Zondag: 10:00-16:00