JBL Tune 120TWS

JBL Tune 120TWS

Ægte trådløse hovedtelefoner.

Sold from 2019 until now

Getting started with your JBL Tune 120TWS

Getting started with your JBL Tune 120TWS

Quick Start Guide

Get up and running in no time with our easy-to-follow Quick Start Guide

Product Registration

Register your product

Do you own this product? Register it here! And claim your warranty or service easily

Register now

Documents & Downloads

Specifications

Enheds-størrelser (mm)
5.8
Enheds-følsomhed ved 1kHz/1mW (dB)
96
Dynamisk frekvensområde (Hz)
20Hz – 20kHz
Impedans (ohm)
14
Antal dynamiske enheder pr. øre
1
Vægt (g)
60.1
Charging Case Weight (oz)
2.1
Vægt (g)
13.6
Earpiece Weight (oz)
0.5
Bluetooth-profiler
A2DP 1.3 AVRCP 1.5 HFP 1.6
Bluetooth-frekvens
2.402 GHz - 2.480 GHz
Bluetooth sender-modulation
GFSK, π/4DQPSK, 8DPSK
Bluetooth sender-effekt
0 - 12dbm
Bluetooth-version
5.0
Ladetid (timer fra helt afladet)
2
Maksimal spilletid (timer)
4
Bluetooth
Ja
Charging cable
Ja
Stemmeassistent
Ja
Indbygget mikrofon
Ja
Smart opladningsetui
Ja
Håndfri opkald
Ja
JBL Pure Bass-lyd
Ja
Genopladeligt batteri
Ja
Fjernbetjening på ørekopper?
Ja
Ægte trådløse
Ja
Trådløse
Ja

Ren bas, ingen kabler.

Ingen ledninger. Intet besvær. Vi præsenterer den helt trådløse JBL TUNE 120TWS. Farverigt design kombineres her med kraftfuld lyd takket være en 5,8 mm enhed med JBL Pure Bass-lyd. Sammen med det elegant designede bærbare opladningsetui leverer ørestykkerne 16 timers ubegrænset musiknydelse. Den ergonomiske form sikrer langvarig komfort. På hvert ørestykke finder du nemme og praktiske kontrolelementer. Et enkelt tryk giver adgang til Siri og Google Now.

5,8 mm enheden med JBL Pure Bass-lyd leverer kraftig lyd til alle dine afspilningslister.
Oplev friheden ved en trådløs livsstil, når du er på farten. Nu kan du lytte til musik, klare dine opkald eller træne uden at blive forstyrret af sammenfiltrede ledninger.
​​Takket være den enkle styring af håndfri opkald, og de praktisk placerede knapper på øretelefonerne, behøver du aldrig gå glip af et opkald, når du træner eller er på vej til arbejde. Opret forbindelse til Siri eller Google Assistent med et tryk på en knap.
Lyt, så længe du lyster, fra morgen til aften. Og hvis det ikke er nok, kan du få en times ekstra spilletid ved at lægge ørestykkerne i det elegante opladningsetui i blot 15 minutter.
Et udvalg af friske farver viser, at din stil er lige så vigtig for dig som din musik.

FAQs & How-Tos

11 results
  • This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.
  • It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all True Wireless Stereo earphones and cases.
  • If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

  • • Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.

    • Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.

    • Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.

    • Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.

    • Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.

    • Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.
  • Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
  • 1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).
  • This headphone does not feature volume control. You must manually control volume from your device.
  • If the left ear pod is silent, please perform a new pairing with the right pod like shown in the quick-start guide.
    Take them out of the charging case and click the  center button on both the left and the right pod 3 times.
    This forces a new pairing between the pods, and the left pod should automatically pair with the right pod from now on once you remove both pods from the charging case.

    If you still cannot get the Left ear to play, please perform a factory reset by placing both pods in the charging case, while the charging case is charging. Now press the button on the right pod, and hold it for more than 5 seconds. You have now reset to factory settings. (Please note: If you have performed a factory reset, you will need to remove the headphones or "forget this device" from any smart phone or tablet they were once connected to. This will allow your device to now search for the newly restored headphones under BT devices)


    The right pod is the primary, which is connected to your source, usually a smartphone.
    The left pod is the secondary, which connects to the right pod.
     

  • The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.
    1. Forget/unpair the headphones on your device.
    2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
    3. Pair the headphones to your device and see if this resolves the problem.
    4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
    5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
      • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
      • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
      • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
      • Pair the buds to your Source Device.
  • If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
< 1 2 >

Can’t find what you’re looking for?

Call us

Call us

Call us now at: +45 32712498

Monday - Friday: 09.00-17.00

E-mail us

E-mail us

We are here Monday – Sunday to answer you as fast as we can!

Email us
Chat with us

Chat with us

Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00

message

WhatsApp Us

Send us a message here 

Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00