JBL Tune 115TWS
Totalt trådløse øretelefoner
Sold from 2020 until now
Getting started with your JBL Tune 115TWS
Documents & Downloads
Specifications
- Enheds-størrelser (mm)
- 5.8
- Enheds-følsomhed ved 1kHz/1mW (dB)
- 108
- Dynamisk frekvensområde (Hz)
- 20 Hz – 20 kHz
- Impedans (ohm)
- 14
- Antal dynamiske enheder pr. øre
- 1
- Vægt (g)
- 41.5
- Charging Case Weight (oz)
- 1.5
- Vægt (g)
- 10.3
- Earpiece Weight (oz)
- 0.4
- Bluetooth-profiler
- A2DP 1.3, AVRCP 1.5, HFP V1.7
- Bluetooth-frekvens
- 2.4 GHz – 2.4835 GHz
- Bluetooth sender-modulation
- GFSK, π/4DQPSK, 8DPSK
- Bluetooth sender-effekt
- 0 - 12dbm
- Bluetooth-version
- 5.0
- Charging case battery life (max hours)
- 15
- Ladetid (timer fra helt afladet)
- 2
- Maksimal spilletid (timer)
- 6
- Bluetooth
- Ja
- Stemmeassistent
- Ja
- Indbygget mikrofon
- Ja
- Smart opladningsetui
- Ja
- Håndfri opkald
- Ja
- JBL Pure Bass-lyd
- Ja
- Genopladeligt batteri
- Ja
- Ægte trådløse
- Ja
- Trådløse
- Ja
Ren bas. Ingen kabler.
Fordyb dig i din egen verden. Uanset om du lytter til musik eller modtager opkald, er her ingen ledninger, der holder dig tilbage. Med Dual Connect kan du bruge ethvert af de to ørestykker, eller begge to, præcis som du foretrækker, i både stereo og mono. Dine yndlingsartister lyder fantastisk med JBL Pure Bass. Med op til 21 timers batteritid og en behagelig pasform kan du holde festen kørende dag og nat. Og hvis du savner resten af verden, kan du foretage og afslutte opkald, eller tale med din stemmeassistent, med en enkelt finger. Så enkelt er det!
FAQs & How-Tos
-
It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all True Wireless Stereo earphones and cases.Was this helpful? Thank you for your feedback! -
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback! -
• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.Was this helpful? Thank you for your feedback! -
Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.Was this helpful? Thank you for your feedback!
-
1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).Was this helpful? Thank you for your feedback!
-
This headphone does not feature volume control. You must manually control volume from your device.Was this helpful? Thank you for your feedback!
-
The two earpieces of your TWS headphones should normally be connected together without issue. However, if they are no longer paired to each other, please follow these steps, in order.
- Forget/unpair the headphones on your device.
- Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
- Pair the headphones to your device and see if this resolves the problem.
- If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
- Initiate a Product Reset to reset the earbud’s Bluetooth connection.
- Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
- Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
- Manually pair the 2 buds together again, as you did in step 2. This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
- Pair the buds to your Source Device.
Was this helpful? Thank you for your feedback! -
This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09.00-17.00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00