JBL JR300BT
Trådløse on-ear hovedtelefoner til børn
Sold from 2017 until now
Getting started with your JBL JR300BT
Documents & Downloads
Specifications
- Enheds-størrelser (mm)
- 32.0
- Dynamisk frekvensområde (Hz)
- 20 Hz - 20 kHz
- Impedans (ohm)
- 32.0
- Antal dynamiske enheder pr. øre
- 1.0
- Vægt (g)
- 110.0
- Vægt (oz)
- 3,88
- Bluetooth-profiler
- HFP v1.5, HSP v1.2, A2DP v1.2, AVRCP v1.5
- Bluetooth-frekvens
- 2.402GHz-2.48GHz
- Bluetooth sender-modulation
- GFSK,π/4DQPSK, 8DPSK
- Bluetooth sender-effekt
- 0-4 dbm
- Bluetooth-version
- 4.0
- Ladetid (timer fra helt afladet)
- <2
- Maksimal spilletid uden aktiv støjreduktion (timer)
- 10.0
- Maksimal spilletid (timer)
- 12.0
- Bluetooth
- Ja
- On-ear
- Ja
- Genopladeligt batteri
- Ja
- Fjernbetjening på ørekopper?
- Ja
- Lynopladning (5 min. = 1 t spilletid)
- Nej
- Trådløse
- Ja
- Lydstyrke-begrænsning
- Ja
"Young rockers unite!"
De trådløse JBL JR300BT hovedtelefoner er sikre, lette og børnevenlige. De leverer op til 12 timers legendarisk JBL-lyd - og festlig stil til de yngste musikfans. For at beskytte hørelsen er hovedtelefonerne konstrueret sådan, at lydstyrken altid er under 85 dB. Betjeningen klares let - helt uden voksenhjælp. Børnene får en skøn lytteoplevelse med den ekstra blød-polstrede hovedbøjle og de fjerlette og velsiddende ørepuder. Ungerne vil elske muligheden for at gøre hovedtelefonerne personlige med de medfølgende klistermærker.
FAQs & How-Tos
-
These headphones consist of plastics, synthetic leathers and foams. All JBL Jr products were put through extensive tests and are compliant with Standard Consumer Safety Specification for Toy Safety.Was this helpful? Thank you for your feedback!
-
Press the power button located on the bottom of the Right Ear cup. If this is your first time using the headphones, it should immediately start looking for a device to connect to. Make sure that the device that you are trying to connect to is in pairing mode. The JBL JR300BT should display on your discoverable devices within 2-5 seconds. If the headphones have not successfully connected to the device, press and hold the Bluetooth button located next to the Power button on the Right Ear Cup for 2 seconds. As the headphones go into pairing mode, they should connect to your device within 2-5 seconds.Was this helpful? Thank you for your feedback!
-
• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.Was this helpful? Thank you for your feedback! -
Yes. This headphone has a built in microphone. To answer a call, press the power button which is located on the Left Ear Cup for 1 second. If you wish to hang up the call, press and hold the power button for 2 seconds.Was this helpful? Thank you for your feedback!
-
Press and hold the power button located on the RIGHT ear cup. Make sure that the device is on and in Bluetooth range. If this is the first time connecting the device, it will automatically go into pairing mode. You will notice the LED light alternate between blue and white as it searches for a device to connect to. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect.Was this helpful? Thank you for your feedback!
-
To reset the headphones, power on the headphones and plug in the USB cable into a USB charger or USB port. Paired mobile devices should disconnect and the led should be constant white. When unplugging the USB cable, the headphones will power off. When manually powering on the headphones, and the last connected mobile phone is not in range, the headphones will revert to Bluetooth Pairing mode ( blue led will blink ) after 5 seconds. Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09.00-17.00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00