AVR 171S
Netværksparat lyd-/videoreceiver med 700 watt, 7.2 kanaler, AirPlay og Bluetooth
Getting started with your AVR 171S
Documents & Downloads
Specifications
- Power Requirement
- 220V - 240V AC, 50Hz/60Hz
- Dimensions (H x W x D – Metric/English)
- 133mm x 440mm x 300mm (4-3/4” x 17-5/16” x 11-13/16”)
- Weight (Metric/English)
- 5.1 kg (11 lb)
- Stereo Power
- 100 watts per channel, two channels driven @ 6/8 ohms, 20Hz – 20kHz,
- Multichannel Power (one channel driven)
- 100 watts per channel, two channels driven @ 6/8 ohms, 20Hz – 20kHz,
- High Instantaneous Current Capability
- 42 Amps
- Signal-to-noise Ratio (IHF-A)
- 100 dB
- Slew Rate
- 40V/sec
- Input Sensitivity/Impedance
- 250mV/27k ohms
- Television Format
- PAL
- Input Level/Impedance
- 1Vp-p/75 ohms
- Output Level/Impedance
- 1Vp-p/75 ohms
- Video Frequency Response (Component Video)
- 10Hz – 8MHz (–3dB)
- HDMI Version
- 2.0 + 3D ready
Højtydende lyd-/videoreceiver med et væld af trådløse forbindelsesmuligheder, seks HDMI-indgange og 700 watt vellyd. Effekt, ydeevne og flere tilslutningsmuligheder, end nu nogensinde kommer til at bruge. Den netværksparate Harman Kardon®AVR 171S er svaret på kræsne entusiasters krav om ydeevne og alsidighed. Her er masser af muskelkraft: op til 700 watt (100 watt pr. kanal). A/V-receiveren med 7.2 kanaler er udstyret med HARMAN TrueStream Bluetooth®, Apple AirPlay, vTuner™-internetradio og Spotify Connect, så du kan afspille lyd på et væld af måder. Med seks 3D-forberedte HDMI® 2.0-indgange (herunder én med MHL til mobile enheder) og to HDMI-udgange har du en overflod af tilslutningsmuligheder til alt det, du elsker: film, HDTV, sport, MHL-udstyrede enheder og Roku Streaming Stick™. Men AVR 171 har ikke bare gode forbindelser. Det allerbedste er lyden. Dette er Harman Kardons første receiver med den eksklusive Natural Sound Processing (NSP), som skaber fyldig og omsluttende surroundlyd fra enhver kilde, ikke mindst når du afspiller i stereo via nettet. EzSet/EQ™ III-systemet kalibrerer receiveren til dine højttalere og dit lyttemiljø. AVR 171S er også let, takket være HARMAN GreenEdge™-certificeringen, så den leverer alle de kræfter, du skal bruge, mens den skåner miljøet. Hvis du bare vil have det hele, behøver du ikke lede længere.
FAQs & How-Tos
-
Yes, this is correct. The AVR 1x1S does not support OSD on HDMI 2 out, only on HDMI 1. If customers want OSD on two HDMI outputs, they can buy the AVR 370.Was this helpful? Thank you for your feedback!
-
Yes, this is correct. The AVR171, 171S, 1710 & 1710S only supports OSD on on the HDMI 1 output. HDMI 2 doesn't not show the OSD. The AVR370 and 3700 supports OSD on both HDMI outputs.Was this helpful? Thank you for your feedback!
-
Yes, in the HDMI Setup Menu, it is possible to select either �Sound To TV� or �Sound To Amp�, Amp being the AVR. This detail is not mentioned in the owner's manual.Was this helpful? Thank you for your feedback!
-
Yes, download the Harman Kardon Remote app to do this.Was this helpful? Thank you for your feedback!
-
No, only analog audio sources are available for Zone II.Was this helpful? Thank you for your feedback!
-
You can send any 4k video signal into the HDMI inputs of your AVR, and it will be sent to your TV screen from the HDMI output, either in 4k or 1080p. Sometimes it may be necessary to switch off the TV set, then switch it on again, to activate a new "handshake" between the devices, in order to open for the 4k signal, if normal HD 1080p signal was the last signal used. Please note that not all 4k signals can be viewed. Many streamed videos from Youtube will work, as will any 4k material that you have recorded yourself, and many TV boxes will work also. However, HDCP 2.2 protected material will not be shown in 4k, but will be converted to full HD 1080p signals, because these AVRs do not support HDCP 2.2 digital copy protection. HDR is not supported.Was this helpful? Thank you for your feedback!
-
The two subwoofer outputs are parallel, meaning that when changing subwoofer settings in the setup menu, both outputs will be adjusted. Establish the 7.2 system simply by adding a second subwoofer to an existing 7.1 system, connecting it to sub output 2.Was this helpful? Thank you for your feedback!
-
At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.Was this helpful? Thank you for your feedback!
-
We designed the USB folder data to show the latest modified folder and it is a design preference. It is not possible to change this setting.Was this helpful? Thank you for your feedback!
-
This is sometimes a problem with wired connections to computers or NAS drives. There is no way to change this, unfortunately.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09.00-17.00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00