AVR 151
375-watt, 5.1-kanals audio/video-receiver med netværk
Getting started with your AVR 151
Documents & Downloads
Specifications
- Power requirement
- 220V – 240V AC/50Hz – 60Hz
- Power consumption
- <0.5W (standby); 410W maximum
- Weight
- 4.6kg (10 lb)
- Frequency range
- 87.5MHz –108.0MHz
- Signal-to-noise ratio (mono/stereo)
- 70dB/68dB
- Distortion (mono/stereo)
- 0.2%/0.3%
- Stereo separation
- 40dB @ 1kHz
- Selectivity (±400kHz)
- 70dB
Denne 375-watt, højeffektive 5.1-kanals A/V-receiver får din musik, dine film og dine tv-serier til at lyde bedre end nogen sinde før. Uanset om det er din Blu-ray™-afspiller, HD-kabel-boks eller spillekonsol, vil du have den bedste billedkvalitet og lyd. Og du har brug for én enkel måde at tilslutte dem alle på. Harman Kardon® AVR 151 er en 5.1-kanals audio/video-receiver med netværk, som har fire 3D-ready HDMI®-indgange med 4K-pass-through – tilslut dem én gang, og du er klar. Med DLNA® 1.5 kan du streame lyd fra dine enheder med netværk, og den integrerede vTuner™-internetradio giver dig forbindelse til en hel verden af online lydunderholdning. AVR 151 er alsidig og muskuløs – den kan udsende op til 375 watt. Med den kan du høre kraftig lyd med al den nøjagtighed, du kender og elsker fra Harman Kardon-produkter. Receiveren er også lettere takket være HARMAN GreenEdge™-certificeringen. Du vil opleve sand styrke – bare i en mere miljøvenlig formfaktor. Og hvis du er en af dem, der gerne vil have mere kontrol, kan du hente Harman Kardon Remote-app'en. Den giver dig friheden til at styre din hjemmebiografoplevelse fra din egen velkendte enhed. Elegant, let og kraftig – Harman Kardon AVR 151 er den perfekte balance mellem alsidighed og smuk lyd.
FAQs & How-Tos
-
No, 4K upscaling is not possible. It was mentioned in the specification sheet and on the web page that this feature was supported, but that is an error.Was this helpful? Thank you for your feedback!
-
Yes, in the HDMI Setup Menu, it is possible to select either �Sound To TV� or �Sound To Amp�, Amp being the AVR. This detail is not mentioned in the owner's manual.Was this helpful? Thank you for your feedback!
-
This is sometimes a problem with wired connections to computers or NAS drives. There is no way to change this, unfortunately.Was this helpful? Thank you for your feedback!
-
The Harman AVR App controls your receiver through your smartphone, which communicates via your wireless home network. Please make sure that your AVR is properly connected to your network router, with cable for the smaller models. If you have no wireless home network, you cannot use the app.Was this helpful? Thank you for your feedback!
-
Yes, on your computer, enter the IP address of the receiver in the internet browser. In the page that opens, it is possible to change the name.Was this helpful? Thank you for your feedback!
-
For your personal safety and to avoid possible damage to your equipment and speakers, it is always a good practice to turn off and unplug the AVR and ALL source equipment from the AC output before making any audio or video system connections.Was this helpful? Thank you for your feedback!
-
There are five possible reasons for the receiver shutting down. 1. There is a problem internally with the receiver. 2. There is a problem with one or more of your speakers. 3. There is a problem with one or more of your speaker wires. 4. There is a problem with the speaker wiring done on your system. 5. The unit is overheating. No ventilation. First, check the wiring at every speaker terminal at the back of your receiver and at the back of your speakers. A single strand of speaker wire crossing from one terminal to another would be enough to cause the amp to shut down or go into PROTECT. If you do not find any problems with any of the wiring, you should disconnect all speakers from your receiver. If the receiver continues to go into PROTECT, the problem is in the receiver. Please submit a case on the Contact Us page. They will be able to assist you. However, if it turns on, the problem is elsewhere. Begin reconnecting one speaker at a time. Eventually you will connect a speaker that will cause the receiver to shut down. At this point you have found your culprit. On the other hand, it may just be overheating. You must have at least 2 - 3 inches of space between the top of the unit and any shelf or component above the unit. The unit should not be inside a sealed compartment when being used. The unit must be able to breath. There are very powerful amps in these receivers. If they run too hot, they will shut down. An external fan can help this.Was this helpful? Thank you for your feedback!
-
If you have enabled HDMI-link (CEC function), then you will experience that your AVR will do some actions based on the CEC function coming from your TV, which in this case it will follow your TV when it goes into standby.Was this helpful? Thank you for your feedback!
-
With some Blu-ray discs, you have to go to the Settings Menu of your Blu-ray player and select "Bitstream" or "Bitstream Native". This will carry the DTS HD Master signal to be decoded in the AVR, and the AVR front panel should show the correct text.Was this helpful? Thank you for your feedback!
-
Yes, this is a normal characteristic of this system.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09.00-17.00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00