How To
How To
1674 results
-
Yes, the Harman Kardon SB20 features IR learning functionality. Please follow these steps: Step 1: Power on your Harman Kardon SB20. Step 2: Press and hold the SB20 surround button for 5 seconds. This will make the system enter IR learning mode. The power button will flash amber while in learning mode. Step 3: Now the SB20 can learn to respond to your TV remote control. These commands can be learned: To learn the SB 20 VOL+ command, press volume + on the SB 20 top panel, then press VOL+ on your TV remote control. The power button should blink amber, and the surround button will light up for 1 second. This will indicate that the process was successful. Repeat the procedure for volume-, mute and power on/off. Step 4: To exit the learning mode, press and hold the surround button for 5 seconds again. The power button light goes out.Was this helpful? Thank you for your feedback!
-
No, in order to go through the setup procedure, it is necessary to activate the (OSD) On-Screen-Display, and this is not possible on the front panel buttons, you need the remote control. Only the remote control features the necessary OSD button.Was this helpful? Thank you for your feedback!
-
Yes, charging and listening simultaneously is possible. With N90Q, charging takes place at all times when listening to digital audio from a USB socket.Was this helpful? Thank you for your feedback!
-
No, the noise cancelling function is always active when Bluetooth is on. If you want to listen to music without NC on, you must use the cabled audio connection.Was this helpful? Thank you for your feedback!
-
Yes, but only via cable, and noise cancelling cannot be activated meanwhile. Since the charging socket is located on top of the ear pod, adjustment is limited in that direction while the micro-USB plug is inserted.Was this helpful? Thank you for your feedback!
-
The SB20 supports these programmable IR codes for your TV remote: Volume+, Volume-, Mute and Power commands.Was this helpful? Thank you for your feedback!
-
Yes, you can control the No. 585 over port 7701, providing the control is set for Ethernet in the menu. The commands are the same as RS232 and you connect to it by telnet on port 7701 of the IP Address of the unit. Note there is no echo of the command when you type and it answers with a copy of the command and OK if it accepted the command and EH? if it did not.Was this helpful? Thank you for your feedback!
-
The JBL Bar 500 does not support rear/surround speakers. Alternatively the JBL Bar 800/1000 has detachable wireless rear speakers included.Was this helpful? Thank you for your feedback!
-
No, it only supports one Bluetooth connection. Simply disconnect the paired phone/tablet from your Bluetooth device settings, then hold down the Bluetooth button for 3 seconds, and then you are able to pair with the new smartphone/tablet.Was this helpful? Thank you for your feedback!
-
The JBL Bar 300 does not support a subwoofer. Alternatively the JBL Bar 500 has a wireless subwoofer included.Was this helpful? Thank you for your feedback!
-
It is not possible to clean the clear dome of the AURA. The dome cannot be removed without damaging the product. The only solution if debris falls into the AURA is to try to shake it out through the bass tube. We cannot recommend using a vacuum cleaner to suck or blow through the bass tube.Was this helpful? Thank you for your feedback!
-
Yes, when the Esquire 2 is switched ON, it can charge a smartphone or tablet (or other USB-chargeable device that matches) through the special USB port. This function is available both when Esquire 2 is running on battery, and when connected to a charging port itself.Was this helpful? Thank you for your feedback!
-
Yes, on your computer, enter the IP address of the receiver in the internet browser. In the page that opens, it is possible to change the name.Was this helpful? Thank you for your feedback!
-
Yes, in the Harman Kardon Remote APP, it is possible to change the AURA's Bluetooth name.Was this helpful? Thank you for your feedback!
-
The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.Was this helpful? Thank you for your feedback!
-
Yes you can wash it if the fabric is dirty. But remember to close the USB cover.Was this helpful? Thank you for your feedback!
-
Is Bluetooth APT X streaming supported by the JBL Bar Studio, Bar 2.1, Bar 3.1, Bar 5.1 and Bar 9.1?The speaker uses Bluetooth version 4.2 but does NOT support APT X.Was this helpful? Thank you for your feedback!
-
Yes, but only with power on the Adapt. When it senses a signal on the analog aux input, the input ring will light up green automatically, and the signal will become available from the line output, for transmission with cable to e.g. an amplifier. It is important to note that there will be a slight delay in the signal that comes out of the line output jack, even if it does not involve any wireless functions.Was this helpful? Thank you for your feedback!
-
With different storage conditions and shipping durations, your power bank may go into deep sleep mode to protect the battery. If the power bank does not start charging your device when used for the first time, connect the power bank to a power source and charge it for 15-30 minutes, it should then work normally. If it still does not work, contact our customer service team and we will be happy to help you: https://support.infinitylab.com/#contactWas this helpful? Thank you for your feedback!
-
This unit is fully dust-proof, and can withstand continuous immersion in water (up to 1.5 meters / 4.9ft for 30 minutes).Was this helpful? Thank you for your feedback!
-
This product is rated IP67, which is different from IPX7. IP67 protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes. It is also resistant against dust. Dust accumulation around electronics can lead to hardware failure, so the IP67 rating is an extremely beneficial addition to this product.Was this helpful? Thank you for your feedback!
-
Our A2DP profile only support SBC Codec for ESQUIRE 2.Was this helpful? Thank you for your feedback!
-
Was this helpful? Thank you for your feedback!
-
The HKTS 65 is a new version of the HKTS 60, with minor improvements. Please select HKTS 60 in the menu.Was this helpful? Thank you for your feedback!
-
The amplifier has a signal sensor on the high-level (speaker level) inputs, so it is not necessary to use a trigger cable when input is high-level, and connected to the high-level inputs. However, low-level input signals through the RCA-phone input sockets do not activate a signal sensor, so use of a trigger cable is MANDATORY for low-level input signal use.Was this helpful? Thank you for your feedback!
-
Always get the latest Bluetooth driver version available for your Computer/PC/Laptop.
The driver (software) should support the following Bluetooth protocol, to be able to conference call from your Computer/PC/Laptop:
• HFP (Hands-Free Profile) driver to make conference calls from your speaker
During conference calls if there is intermittent volume and inconsistent audio quality, it is recommended to select "Stereo" in the Computer/PC/Laptop playback settings.
Was this helpful? Thank you for your feedback! -
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire/Focus 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
There can be differences in the internal hardware that also implies different firmwares. These products feature the same specifications and performance expectations. If the app does not inform you of any new updates, the firmware is current and the product is performing as designed.Was this helpful? Thank you for your feedback!
-
The InfinityLab power bank will not damage your device.
The InfinityLab power bank will deliver the power your device needs during charging, andd the InfinityLab power bank features auto protection against overheating and features overcurrent/overvoltage conditions.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00
