JBL Cinema SB150
Kompakt 150W soundbar med trådløs subwoofer til hjemmebiografen
Sold from 2016 until now
Getting started with your JBL Cinema SB150
Documents & Downloads
Specifications
- Gross Weight
- 17.6 lb (8 kg)
- Frequency response
- 45Hz – 20kHz
- Maximum SPL
- 96dB
- Total Cinema SB150 amplifier power
- 150W
- Dimension Soundbar (L x W x H)
- 31.5" x 3.5" x 2.5" (800 x 90 x 65mm)
- Subwoofer Dimension(L x W x H)
- 4.7" x 11.8" x 16.1" (120 x 300 x 410mm)
- Subwoofer Weight
- 9.2 lb (4.2kg)
- Soundbar Weight
- 3.3 lb (1.5kg)
Liven up your living room with cinema quality sound
JBL Cinema SB150 er strømlinet og let at betjene.<CRLF>Oplev storslået biograflyd i dit hjem - for meget mindre, end man skulle tro. I tilgift til den kraftfulde men kompakte og trådløse subwoofer får du muligheden for at afspille din yndlingsmusik trådløst fra din telefon eller tablet via Bluetooth. De tre færdige lyd-indstillinger - "Nyheder", "Musik" og "Film" - sikrer den bedst mulige oplevelse ved forskelligt indhold.<CRLF>Det er også muligt at justere subwooferens lydstyrke separat, så du får ekstra kontrol over basydelsen. JBL Cinema SB150 sluttes nemt til ethvert fladskærms-tv med et enkelt kabel og leverer 150 W massiv lyd. Dette kunne meget vel være den løsning, du har ledt efter til dit hjem.
FAQs & How-Tos
-
The Bluetooth connection will not keep playing once you have switched the source. Simply press play again on your Bluetooth device to start streaming once again.Was this helpful? Thank you for your feedback!
-
On the back of the SB150 subwoofer, you will find a "pair" button. Hold down the pair button for 3 seconds. It will start flashing amber rapidly, indicating that the pairing mode has begun. You don't need to press other buttons to make a connection, once the amber light is steady, it is connected to your SB150 soundbar.Was this helpful? Thank you for your feedback!
-
Unplug the power cord from soundbar. While holding down the VOLUME + button, plug the power cord into the soundbar. A green LED, followed by a blue LED will light up, after which the soundbar will go into standby. The SB150 is now reset.Was this helpful? Thank you for your feedback!
-
If the pairing mode is not succesful, please move the subwoofer closer to your SB150. The pairing process can take up to 30 seconds before a connection has been established.Was this helpful? Thank you for your feedback!
-
Try resetting the device, and remove the Bluetooth device on your source device in the settings. Now Bluetooth-pair with it again. If the unit still does not work as intended, please contact our helpdesk.Was this helpful? Thank you for your feedback!
-
If any update exist, then it is only possible to get it updated, via our authorized service center. The USB port on the back, is meant for service use only. Contact support for more information.Was this helpful? Thank you for your feedback!
-
No, your subwoofer is not defective at all! This is normal and by design of the product after it has been paired for a longer period of time.Was this helpful? Thank you for your feedback!
-
It is usually not necessary to replace an unresponsive remote control. First, check to see if there is a small plastic tab extending out of the base of the remote control. This is a protective sleeve installed on new remote controls to prevent the battery from draining. Pull this tab to remove the plastic sleeve. The sleeve must be removed before the remote will operate. If the sleeve was removed or not present and the remote control is not working then a new battery should be installed before replacing the remote control. There is a small slide out drawer that houses the battery. The battery type will be either CR2025 or CR2032 for remotes of this size. Replacement batteries are commonly available from most electronic and convenience stores that sell small batteries. Check the number on the original battery and replace it with a battery that uses the same number. These steps will typically solve the problem.Was this helpful? Thank you for your feedback!
-
The three EQ setting (Movie, Music, News) adjusts the sound setting of the SB 150. This feature provides a superior audio experience customized to the content being played.Was this helpful? Thank you for your feedback!
-
With HARMAN Volume you can set your desired volume between low, medium and high. You can listen to your audio without sudden distracting changes such as blasts from ads, and volume variations as you switch between channels on your TV. Other benefits include full sound effects even at low volumes, this means if you are watching movies (DVD, BlueRay disc) and HARMAN volume is set to low volume, then the signal is more compressed, than what the other volume levels is. This will allow you to hear natural, consistent sound at low volume level, and not only hearing voice conversation from movies, giving you the same movie experience just with lower volume. What is best for you is a matter of personal preference, so we recommend playing around with the three different levels.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09.00-17.00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00