How To

Spatial sound gives a more natural, realistic and accurate immersive experience whether you are listening to music, movies or games.

The technology processes more details from any stereo content, which generates reflections and reverberation signals. The integrated head tracking means that sound stay fixed in space even when you turn your head, which adds a new layer of realism to your immersive listening.

This connection is intended for software and service updates only.

The Smart Tx draws power from the source when using it with a USB-C connection. The battery life of the Smart Tx is 18 hours when the product is connected with a 3.5mm aux connection or used without a connection to a power source.

We recommend inserting the ear tips (L for left, R for right located at the end of the ear tip extension) in the ear first and then proceed to wrap the ear loop around your ear. Please make sure to try all three sizes to insure the most comfortable fit.

The Bluetooth range varies. However, you should get up to 15 meters (just under 50 ft) when using the product indoors. If you are using the headphones outside, conditions vary based on surroundings and body mass. For the best connectivity results, please make sure that the device you are paired to is in the front of your body.

Bluetooth range is normally up to about 10 m. More than that the signal will get unstable.

A clip has been included to help ensure the best fit and security of the headphones. Placing the clip on the audio cord and attaching to the top back of your shirt you should be able to twist your head right and left without the clip pulling your ear.

The Smart button activates Ambient aware settings: Off, Low, High.

These two models have 40 mm speaker units.

AURA Studio is a Bluetooth speaker plus microphone built-in, where AURA has Wi-Fi built-in for AirPlay, DLNA and Spotify Connect solutions.

Dolby Atmos is an object-based surround sound format. Harman Kardon MultiBeam is a beam-forming surround sound system that creates a wide surround sound effect.

100 is in-ear, 300 is on-ear, 700 is over-ear.

You'll have all the benefits from HDMI 2.0, but with 2.0a you will also have HDR (High Dynamic Range). Don't confuse HDR with cameras, this is used for TV's that support HDR content. In short, if a Blu-Ray supports HDR, it can enhanced dark scenes from a movie with this option.

The difference is that the new ECO versions of Go 3 and Clip 4 are made from 90% PCR (Post-Consumer Recycled) plastic and wrapped in 100% recycled fabric on the speaker grille, while still delivering the same rich JBL Original Pro Sound and significantly reducing the carbon footprint of the product.

The JBL QuantumSURROUND algorithm is specifically designed from the ground up to work with JBL Quantum gaming headsets—the software perfectly complements the hardware for incredibly realistic immersion. JBL QuantumSURROUND provides a strong sense of externalization, meaning that sound feels like it’s coming from loudspeakers in a professional listening room—or from the game world around you. With other spatialized audio solutions, it still feels like the sound is coming from the headphones, or just outside of them.

You can get the professional sound precision and accuracy with head-tracking enhanced JBL QuantumSPHERE 360™ on your PC while gaining sound immersion with JBL QuantumSPATIAL 360™ on your platform. JBL QuantumSPHERE 360™ is accessed through the USB-C dongle/adaptor on your PC passing through the QuantumENGINE. The JBL QuantumSPATIAL 360™ is accessed on consoles through the USB-C dongle/adaptor works without the JBL QuantumENGINE.

The difference is the BTA unit, which is a Bluetooth transmitter. The Soundgear BTA comes with the BTA unit in the box. The Soundgear does not. The BTA can be connected (with a signal cable) to a TV set, a CD player, or any other stereo line-level source, and can then stream this signal to the Soundgear wirelessly, via Bluetooth. TV sound or game sound are possible, since the BTA and the Soundgear use aptX Low Latency, which reduces the audio delay to levels, where picture and sound will be closely synchronized. This is also the secret behind the option to connect two Soundgears to one BTA unit, for two people to share a TV transmission, or a video game. Actually, you can use the BTA to stream to most other Bluetooth headphones and loudspeakers, but only if these devices also support aptX LL will the delay be low enough for video use.

The physical battery in Boombox has a capacity of 10.000mAh @7.4V. This is the charged battery storage. When outputting ( so power from the battery is drawn ), it's using 3.7V, half the storage voltage, which will give you 74Wh - equivalent to a 20.000mAh battery with power stored at 3.7V.

The BDS 335 system is a 2.1 sound system, and speaker set included in this version is HKTS 335 speaker system. The BDS 635 system is a 5.1 sound system, and speaker set included in this version is HKTS 635 speaker system. That is the only difference between these two systems.

Since there is no fixed standard for headphone connections, there are two cables in the box, with different polarity. If one cable does not give good audio results, try the other cable. This usually solves the problem. The majority of phone models (Apple, Samsung from Galaxy S2 model, LG, HTC, Sony, Motorola, Blackberry) require the audio cable with the silver plugs. Pin assignment in this cable from the tip of the plug: R/L/Ground/Microphone. However, some manufacturers, such as some models from Nokia, require a cable with different pin assignment, (R/L/Microphone/Ground). In this case, you should use the audio cable with the black plugs.

The Endurance Jump features the power hook which provides a secure fit ear hook design, which automatically turns the power on/off when putting on or taking off the earphones. The Sprint does not feature the power hook and you manually have to turn on/off the headphones by pressing and holding the JBL logo on the RIGHT ear hook.

Wireless: Old name is Headphone Wireless. New name is Sport Wireless. Body is re-designed, the new body is smaller in diameter, but a bit longer. Angle of sound tube is changed slightly. Audio performance is improved. Enhancers slightly changed. Heartrate: Old name is Headphone Wireless Heartrate. New name is Sport Wireless Heartrate. Construction and design are unchanged.

The only difference between the 500 and 700 series is that the 700 model provides you with a charging case. The features and functionality on the actual headphones themselves are the same.

The only difference between the 500 and 700 series is that the 700 model provides you with a charging case. The features and functionality on the actual headphones themselves are the same.

The SB 250 has optical and auxiliary connections, while the SB 350 has both connections along with HDMI ARC. The SB 250 has the JBL SoundShift feature (one-button switch between TV and Bluetooth connection), while the SB 350 does not. Compared to the SB 250, the SB 350 has a more powerful subwoofer amplifier. The bigger amp will provide listeners with more bass response.

The distance between wall-mounts centers are: JBL BAR Studio: 45 cm. JBL BAR 2.1: 70 cm. JBL BAR 3.1: 70 cm. JBL BAR 5.1: 61 cm JBL BAR 5.1 Surround: 71.85 cm JBL BAR 9.1: 55,5 cm

The Frequency response for the Citation series, except the subwoofer, is 50Hz to 20Khz.
 

The EQ Button activates a special "wide stereo sound" effect. It does not affect bass settings. Turning EQ On/Off does not reset bass level to default value. User can adjust BASS in the Bass +/- control in the APP.

JBL Tour One M2 has integrated high fidelity 40mm neodymium speaker drivers for exceptional high-fidelity sound. Each driver is perfectly tuned to deliver deep bass, balanced mid-range and refined high frequencies for the best on-the-go high fidelity audio listening experience. Super soft ear cushions for a comfortable snug fit and perfect seal. Only the best seal will ensure an immersive spatial audio experience in perfect silence. Use your device for the ultimate high resolution listening experience via Apple Music, Tidal Masters or Amazon Music Unlimited. Immerse yourself fully in spatial audio from any 2-channel audio source via Bluetooth with the JBL Spatial sound technology.  

Software version v.7.9 is the latest for the Flip 3

JBL Bar 9.1 is 884 mm (without the surrounds in charging position). Surrounds add approx. 160 mm on each side, in charging position.

The length from the Aux connector to the bottom of the button panel (cable only, excluding the connector and button panel) is approximately 90 cm.

The length of the cable that goes from the top of the button panel to the bottom of each earbud (cable only, excluding the earbuds and button panel) is approximately 29 cm.

 

The length of the earbuds are approximately 2 cm.

The length of the button panel is approximately 6.5 cm.

 

The overall total length is approximately = 127.5 cm.

The maximum video resolution of the No. 40 HDMI card is 1080i.

The No.536 has several operational and standby modes - the measurements below represent typical values measured at 120VAC: Mode Typical Power Consumption Notes On 210 Watts With no input or output loading Normal (standby) 4.1 Watts/100 Watts Unpon initial power-up/After first use Power Save (Standby) 4.1 Watts Green (Standby) 0.3 Watts OFF 0 Watts Via rear panel switch Note that the No. 536 cannot be shut off by the front button – this is used only for switching the amp in/out of a standby mode. Also note that when set to the Normal standby mode, the amplifier will initially consume the same power as when in the Powersave mode but will change to a higher level after it is switched on for the first time.

The No. 585 will deliver 350 watts into 4 ohms

The overall power rating is 630 W maximum power at 1% THD.
 

With the speaker ON, press and hold the VOL+ and Pause/Play buttons for 5-6 seconds. The Xtreme shuts down, and is now reset. You will need to 'forget' the speaker in Bluetooth settings on your phone/tablet in order to pair it again.

Speakers will dual tweeters gives listeners the ability to have a single speaker to drive two independent channels, ideally stereo left and right. Dual tweeter speakers are usually used for in-ceiling audio applications. They have four terminals (two sets of positives and negatives) used to plug in speaker wires from the amplifier.

The range is approximately 10 meters, depending on the environment.

The Omni 50+ rated power with AC power connected is 4 X 25 Watt. When using battery only, the rated power is 4 X 15 Watt.

Both the OMNI BAR+ and its subwoofer have 200W of power amplification, which means that total system power is 400 W.

These are the supported languages for the Everest GA series.

• English (US, UK, CA, IN, AU)
• German
• French (CA, FR)
• Japanese
• Portuguese (BR)

More will be added in future Google releases.

You can connect the JBL Smart Tx to any audio source to elevate your wireless sound experience. Use the USB-C cable to connect to a digital audio source such as a phone, tablet or laptop or use the 3.5mm aux to connect to an inflight entertainment system on most airplanes, TV or PC to experience wireless audio.

The Smart Tx gives you full access to the Tour One M3 via the touch screen without the need for your phone or app. The Smart Tx can also stream your audio to any Auracast enabled supported headphones or speakers.

This connection is intended for software and service updates only.

Voltage is 100 - 240 Volt AC. Maximum power consumption is 120 Watts.

Soundgear Sense provides two wearing styles, either as regular TWS headphones with an ear hook for a secure fit, or as a neckband headphone with the optional detachable neckband. Both wearing styles offer the same open ear experience with rich, full-range sound, it is just a matter of your own preference or use case which wearing style you choose. 

Now, with Google Assistant and Alexa available simultaneously on your JBL Authentics speakers, you can choose to use one or both voice services available. This means you can set up just Alexa, just Google Assistant, or both. If you choose to set up both services, they will be at the ready. You can use either of them whenever you want simply by saying either “Hey Google” or “Alexa”.

Windows Sonic is a virtual surround algorithm that is built into Windows 10 PCs. You can read more here:
https://docs.microsoft.com/en-us/windows/win32/coreaudio/spatial-sound

Wireless Stereo Boost allows you to connect two of the same model speakers together for a more powerful listening experience. 

To use this feature, hold the Bluetooth button on both speakers for more than 5 seconds.

The left & right channels can be swapped by tapping the Bluetooth button on the host speaker twice.

The Onyx Studio 8 features Wireless Stereo Boost which allows you to connect two Onyx Studio 8 speakers together for a more powerful listening experience. Please note: You cannot connect the Onyx Studio 8 to other Onyx Studio speakers such as the Onyx Studio 7, 6 and 5.

The JBL Quantum Stream microphone is compatible with the JBL QuantumENGINE software. You can customize or use the following settings/features via the JBL QuantumENGINE:

Microphone settings
Polar patters (Cardioid / Onnidirectional)
Equalizer
RGB LED Light colors + animations/effects
Update firmware + software

You can customize or use the following settings/features via the JBL QuantumENGINE:

Microphone settings

Polar Patterns (Directions that the Quantum Stream Studio picks up the sound)

Equalizer

Lighting settings

Update firmware and software

Only data to make Google Assistant more efficient and Google services faster. When interacting with the speaker you will receive more personalized feedback in the future.

The Vi headphones have a couple different sensors, including a touch sensor (for interacting with Vi), a gyroscope (for rotational motion), accelerometer (for movement or vibrations) and a barometer (for elevation / atmospheric pressure). Plus they house a “custom” sensor that uses visible-light and infrared LEDs along with photodiodes, all in the left ear bud, to determine your heart rate. The headphones can also talk to your iPhone/Android's GPS and Wi-Fi to help with figuring out location and other information.

The Smart Case only supports English, so even if you change the language in the JBL Headphones app, it will remain in English.

The JBL QuantumENGINE supports up to 20 languages. You can select the preferred language in the system section.

The ear cushions are made of protein leather.

Battery icon shows as full at 90%-100% battery remaining.

Battery icon shows as 2/3 full at 50%-90% battery remaining.

Battery icon shows as 1/3 full at 15%-50% battery remaining.

Battery icon shows as empty and flashing at 5%-15% battery remaining - the product should be charged now.

The speaker will switch off at 0% battery remaining automatically to preserve the lifespan of the battery.

The JBL Headphones app supports the file types JPG and PNG. There is no limit on file size, as this depends on how much the phone and app can handle to load the image into the app. When you are uploading the image to the Smart Case, the app will make a screenshot of the image and cut the image, so it fits the shape of the screen. Therefore, the size of this screenshot will be smaller than the size of the image.

The JBL Quantum Stream mic is compatible with the following platforms:

PC (Windows)
PlayStation 4
PlayStation 5
Nintendo Switch
Mobile*
Mac

* Most newer phones are compatible.