How To
How To
-
To turn off the Horizon 2, Press the 'DAB/FM' button until no radio is playing.
This works in the order (from standby/off): DAB / FM / Off.
In Bluetooth mode, if the phone or tablet is disconnected, or nothing is played for 10 minutes, the Horizon 2 will go into standby mode automatically (not changeable).Was this helpful? Thank you for your feedback! -
These two products are identical. The only difference between them is...
HORIZON 2: out-of-the-box is set to HOTEL OFF
HORIZON 2 HOTEL: out-of-the-box is set to HOTEL ON
On either unit, to toggle HOTEL mode ON or OFF, press and hold Alarm 1 and Preset 1. The LCD indicator will show the HOTEL status, ON or OFF.
The unit will retain this setting, even when unplugged. The only way to change the mode is to press and hold the two buttons again. Or course, a Factory Reset will also restore to the original out-of-the-box setting.
When HOTEL mode is ON, these are the following changes that occur.
- Alarm can only be set for a single day.
- Alarm will ONLY work as a buzzer.
- A Room Number can be set.
- A Max Alarm Volume can be set.
- Bluetooth cannot auto-reconnect.
Was this helpful? Thank you for your feedback! -
By pressing Volume - & JBL Connect button for 3 seconds. A voice will tell you the current software version.Was this helpful? Thank you for your feedback!
-
EON 208P:
Two of the inputs are made for stereo use:
CH 5/6 with volume control and ¼” phone plugs or RCA plugs, and
CH 7/8 with volume control and ¼” phone plugs or 3.5 mm stereo input.Also, the Bluetooth wireless input is stereo.
EON ONE:Two of the inputs are made for stereo use:CH 3/4 with volume control and ¼” phone plugs or RCA plugs, and
CH 5/6 without volume control and 3.5 mm input jack
Also, the Bluetooth wireless input is stereo.Was this helpful? Thank you for your feedback! -
Place the USB wireless dongle in the USB-C connector of your device and place the earbuds in your ears. The earbuds will automatically connect to your USB wireless dongle. If the earbuds don't pair automatically you can manually pair them again by connecting the JBL Quantum TWS to a mobile device via Bluetooth and open the JBL Headphones app. Turn on the "Dongle Pairing" mode and then press the pairing button on the USB wireless dongle. (Note: USB wireless dongle needs to be connected to an activated device). You will get a message on your JBL Headphones app that the pairing is successful and then press "Understood".Was this helpful? Thank you for your feedback!
-
This headphone does not have volume control. It features a one button in-line remote that enables you to pause/play, skip tracks and answer/hang up phone calls. The microphone that is built into the remote permits use as headset with a mobile phone.Was this helpful? Thank you for your feedback!
-
You can delete specific voice recordings associated with your account by going to History in Settings in the Alexa App, drilling down for a specific entry, and then tapping the delete button. Or, you can delete all voice recordings associated with your account for your Harman Kardon Allure speaker, by selecting the applicable product at the Manage Your Content and Devices page at www.amazon.com/mycd. and deleting voice recordings. However, this may degrade your Alexa experience.Was this helpful? Thank you for your feedback!
-
To get the full potential of the HDMI content/source you have in your home, then you need to enable HDMI UHD deep color option on your TV for the HDMI output port (ARC).
Since there are tons of different TVs and manufactures out there, the best way to see if your TV can use 10-bit color on HDMI, is to read the TV's manual or call their support section.Was this helpful? Thank you for your feedback! -
Press the Bluetooth source button on your BDS remote. In the right top corner of your TV screen, there should be a button called "Pair". Jump to the "Pair button" to perform pairing by using the arrow keys on your remote control. Click OK while being on the pair button. Once pressed, a pop-up screen will appear, this indicates pairing mode is active for 3 minutes. Go to Bluetooth settings on your mobile device, find the BDS in the list and connect. If you want to pair a second device, please repeat the procedure to activate pairing mode.Was this helpful? Thank you for your feedback!
-
For Citation ONE, Citation 100, Citation Sub and Citation Surround, Press and hold the RESET button on the speaker for 5 seconds. For Citation 300, Citation 500, Citation Bar and Citation Tower, Press and hold the RESET button on the speaker for 5 seconds, or select the Factory Reset option in the touch screen settings menu.Was this helpful? Thank you for your feedback!
-
Once the speaker/soundbar is connected to the network, software updates will automatically be sent to the product through Wi-Fi or the internet, if availableWas this helpful? Thank you for your feedback!
-
Once the speaker/soundbar is connected to the network, software updates will automatically be sent to the product through Wi-Fi or the internet, if available
Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00