How To

Support Overview / How To

How To

1676 results

Sort

Page size

How to check Firmware Version

To check the firmware version:
Press and hold the 'Preset 1' & 'Preset 5' buttons for more than 10 seconds.

Was this helpful? Thank you for your feedback!
How To Check Software Version

To find out the software version, press and hold the [VOL- ] and [SOURCE] buttons simultaneously. The software version will scroll across the front display.

Was this helpful? Thank you for your feedback!
How to clean and store your headphones
To clean your headphones, please follow the instructions below:
1. Clean earpads and headphones with a soft, slightly damped cloth.
2. Do not soak, submerge or allow moisture to enter near drivers and cable jacks.
  1. Earpads and cables can be purchased if worn out at www.Marklevinson.com.
3. Use a polishing cloth to wipe down after use to remove fingerprints etc.
Please keep them in the provided hard traveling case when not using the headphones to protect them from dirt and other substances.
Was this helpful? Thank you for your feedback!
How to clean foam ear tips?

When the foam ear tips get dirty, it is recommended to clean them with a soft, dry cloth. It is not recommended to use water or wet wipes, doing so can affect the durability.
Important: Alcohol and other solvents should never be used as these may damage the surface of the ear tips.

Was this helpful? Thank you for your feedback!
How to clean the glass and device
So your Pulse 4 got dirt on it, or even fingerprints, and you want to show off the device the best way possible.
Keep reading this article, and we will instruct you on how to clean the glass and device.

How to clean your speaker
- Dirt and stains on your speaker can be cleaned under lukewarm running tap water.
- Use a soft cloth, preferably cotton, to clean the glass and to remove fingerprints. Hold the top part to avoid adding more prints to the glass part.
Remember not to charge the device while it is still wet. The charging port needs to be completely dry before charging.
Contact our Customer support for more help and advice to keep your speaker top-notch!
Was this helpful? Thank you for your feedback!
How to clean your earbuds
Use a clean cotton swab slightly moistened with alcohol to:
1. Remove earwax and dirt from the ear tips on your earbuds.
2. Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
3. Clean the grooves on the cover and at the bottom of the charging case.
After cleaning, make sure the charging case and earbuds are dry before putting the earbuds back into the charging case.

TIP: We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.
Was this helpful? Thank you for your feedback!
How to clean your Quantum headphone

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water get into the speaker chamber, as it will damage the speaker drivers.

Was this helpful? Thank you for your feedback!
How to clean your speaker and remove dirt from it

Our FLIP 5 speaker is an "All-weather companion," and sometimes it can get dirt and other substances on it. Clean your speaker under lukewarm water from your water tap, and use a microfiber cloth to remove stains. Do not use any alcohol or other to remove stains and dirt. Do not charge your product while the charging port is wet; make sure it is dry before you connect it to a charger. Contact our Customer support if you need more advice.

Was this helpful? Thank you for your feedback!
How to connect a Bluetooth device

With a short press of the dedicated Bluetooth button on the underside of the right ear cup, it powered on and enter the pairing mode.

Was this helpful? Thank you for your feedback!
How to connect a Bluetooth device
Connecting a Bluetooth device for your Enchant Soundbar
1. Make sure your Enchant soundbar is turned on by pressing the power button
2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar.
  1. Press the dedicated source button on top of your Enchant soundbar
  2. Press the source button until you see "Bluetooth" in the front of the Enchant display. Below is the order when using the source button (note that on Enchant 800 there is only 1 HDMI)
1. The second option is to use the Remote control included with your Enchant soundbar.
  1. Press the "BT" button on your Remote control.
  2. The display will show "Bluetooth pairing"
1. Now that your Enchant soundbar is in pairing mode it is now time to grab your mobile device.
2. Go to Bluetooth settings.
1. Press the enable Bluetooth button.
1. Select the Enchant soundbar and connect with Bluetooth.
You can now stream any music from your favorite device directly to the Enchant soundbar, ENJOY!
Was this helpful? Thank you for your feedback!
How to connect a Bluetooth mobile device

1. Open the Google Home app 2. Select the LINK VIEW 3. Select SETTINGS. 4. There is a line that says Paired Bluetooth Devices. 5. When you select it, it gives you the option to ENABLE PAIRING MODE. 6. Use your voice - "Hey Google, Open Bluetooth" and LINK VIEW will enable Bluetooth connection. You can disable Bluetooth using "Hey Google, Close Bluetooth" Once you have enabled Bluetooth pairing mode on your LINK VIEW, simply go into your Bluetooth settings menu on your mobile device and connect.

Was this helpful? Thank you for your feedback!
How to Connect the Wireless Microphone Set to a Partybox

To successfully connect the JBL Wireless Microphone Set to a Partybox, connect the supplied 6.3mm jack dongle to the Partybox's Microphone Input. Now turn on the dongle and the Partybox. The dongle's Power button light should stay lit, if the light turns off or does not stay lit it is off and needs to be charged with the provided USB cable.*

Now turn on one or both microphones as required and increase the Mic volume and gain to the desired level. The LED screen will show a channel number 'CH-1', 'CH-2', etc. The channel number is not changeable manually, and may change between power cycles, but all channels will connect automatically to the dongle. If the LED screens do not show a channel number, the batteries in the microphones need to be replaced.

*Charging the dongle while in use is not recommended and will likely cause unwanted interference.

Was this helpful? Thank you for your feedback!