How To
How To
1676 results
-
This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.Was this helpful? Thank you for your feedback!
-
Yes, you may charge your speaker from your desktop or laptop, but the charging time will be longer than using the supplied power adapter.Was this helpful? Thank you for your feedback!
-
Here are all the possibilities of how you can charge devices from your power bank.
- InstantGo 5,000 with built-in Lightning cable: 1 (1 x integrated cable)
- InstantGo 5,000 with built-in USB-C cable: 2 (1 x integrated cable, and 1 x USB-C output)
- InstantGo 5,000 wireless: 3 (1 x Wireless, 1 x USB-C output and 1 x USB-A output)
- InstantGo 10,000 with built-in Lightning cable: 2 (1 x integrated cable, and 1 x USB-A output)
- InstantGo 10,000 with built-in USB-C cable: 3 (1 x integrated cable, 1 x USB-C output and 1 x USB-A output)
- InstantGo 10,000 wireless: 3 (1 x Wireless, 1 x USB-C output and 1 x USB-A output)
Was this helpful? Thank you for your feedback! -
You can easily adjust the volume to your choosing while setting your alarm on the Horizon 2. When setting your alarm, choose the Alarm Bell 1 or the Alarm Bell 2 on the top of the speaker. As you go through your settings when choosing an alarm time, it will give you the option to adjust the volume setting you wish to have on the alarm. Just simply adjust the volume by turning the volume knob on the top of the speaker. After you choose the volume, press the volume knob once to move to the next settings option.
Please note: the alarm volume will gradually increase until you choose to either snooze or turn the alarm off completely.Was this helpful? Thank you for your feedback! -
You must first set a radio preset by tuning to a radio station and holding down the 1, 2, or 3 button to save it. After this, the preset will be an option when setting up a new alarm.
When setting up the alarm, the options will be displayed in the following order:
1. Set Alarm Hour.
2. Set Alarm Minute.
3. Set Recurrence - Weekday/Once.
4. Set Ringtone - 4 built-in alarm tones or radio preset 1/2/3 (see information above).
5. Set Light - On/Off.
If the light is set to 'On' when the alarm is set up, once it goes off it will gradually increase in brightness over 10 seconds.Was this helpful? Thank you for your feedback! -
On backup battery power, please wait 50 seconds for the alarm to turn off automatically.
Was this helpful? Thank you for your feedback! -
In order to skip the tracks on the Y500 headphones, slide and hold Volume Up (to skip forward) or Volume Down (to skip backwards) for 3 seconds. These buttons are located on the LEFT ear cup.Was this helpful? Thank you for your feedback!
-
In order to power on and pair the Y500, make sure that the device you are attempting to connect to has the BT on and is in search mode. Move the ON/OFF button from its OFF position to its ON position, which is the middle of the cutout located on the RIGHT ear cup. It will remain there, and the headphones are now ON. The blue LED will start blinking, indicating that Bluetooth pairing is possible. If you need to reset the BT pairing, move the ON/OFF button against the spring load button to the opposite position of the OFF position, and keep it there for 4- 5 seconds. Now the BT system is reset, and new pairing is possible. Please Note: The Y500 features Multi-point Connectivity which allows you to switch from two different devices.Was this helpful? Thank you for your feedback!
-
The Y500 features the speed charge (5 min charging time = 1 Hour Playtime) In order to charge the headphones, use the micro USB charger that is included in the packaging. The charging port is located at the bottom of the RIGHT ear cup. Once the headphones are charging, you will see a solid red light next to the port. Once the headphones are fully charged, the red light indicator will turn off. Please Note: You cannot use the headphones via BT while they are charging. However, you can use the headphones via audio cable while charging.Was this helpful? Thank you for your feedback!
-
The Y500 headphones do not support Apt-X audio codec. However, they do support AAC audio codec.Was this helpful? Thank you for your feedback!
-
Press and hold Volume Up or Volume Down located on the LEFT ear cup for 3 seconds to skip forward or backward.Was this helpful? Thank you for your feedback!
-
Move the ON/OFF button from its OFF position to its ON position, which is the middle of the cutout. It will remain there, and the headphones are now ON. The blue LED will start blinking, indicating that Bluetooth pairing is possible. If you need to reset the BT pairing, move the ON/OFF button against the spring load, to the opposite position of the OFF position, and keep it there for about 5 seconds. Now the BT system is reset, and new pairing is possible.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00