How To
How To
1674 results
-
Yes, the Harman Kardon SB20 features IR learning functionality. Please follow these steps: Step 1: Power on your Harman Kardon SB20. Step 2: Press and hold the SB20 surround button for 5 seconds. This will make the system enter IR learning mode. The power button will flash amber while in learning mode. Step 3: Now the SB20 can learn to respond to your TV remote control. These commands can be learned: To learn the SB 20 VOL+ command, press volume + on the SB 20 top panel, then press VOL+ on your TV remote control. The power button should blink amber, and the surround button will light up for 1 second. This will indicate that the process was successful. Repeat the procedure for volume-, mute and power on/off. Step 4: To exit the learning mode, press and hold the surround button for 5 seconds again. The power button light goes out.Was this helpful? Thank you for your feedback!
-
No, in order to go through the setup procedure, it is necessary to activate the (OSD) On-Screen-Display, and this is not possible on the front panel buttons, you need the remote control. Only the remote control features the necessary OSD button.Was this helpful? Thank you for your feedback!
-
Yes, charging and listening simultaneously is possible. With N90Q, charging takes place at all times when listening to digital audio from a USB socket.Was this helpful? Thank you for your feedback!
-
No, the noise cancelling function is always active when Bluetooth is on. If you want to listen to music without NC on, you must use the cabled audio connection.Was this helpful? Thank you for your feedback!
-
Yes, but only via cable, and noise cancelling cannot be activated meanwhile. Since the charging socket is located on top of the ear pod, adjustment is limited in that direction while the micro-USB plug is inserted.Was this helpful? Thank you for your feedback!
-
The SB20 supports these programmable IR codes for your TV remote: Volume+, Volume-, Mute and Power commands.Was this helpful? Thank you for your feedback!
-
Yes, you can control the No. 585 over port 7701, providing the control is set for Ethernet in the menu. The commands are the same as RS232 and you connect to it by telnet on port 7701 of the IP Address of the unit. Note there is no echo of the command when you type and it answers with a copy of the command and OK if it accepted the command and EH? if it did not.Was this helpful? Thank you for your feedback!
-
The JBL Bar 500 does not support rear/surround speakers. Alternatively the JBL Bar 800/1000 has detachable wireless rear speakers included.Was this helpful? Thank you for your feedback!
-
No, it only supports one Bluetooth connection. Simply disconnect the paired phone/tablet from your Bluetooth device settings, then hold down the Bluetooth button for 3 seconds, and then you are able to pair with the new smartphone/tablet.Was this helpful? Thank you for your feedback!
-
The JBL Bar 300 does not support a subwoofer. Alternatively the JBL Bar 500 has a wireless subwoofer included.Was this helpful? Thank you for your feedback!
-
It is not possible to clean the clear dome of the AURA. The dome cannot be removed without damaging the product. The only solution if debris falls into the AURA is to try to shake it out through the bass tube. We cannot recommend using a vacuum cleaner to suck or blow through the bass tube.Was this helpful? Thank you for your feedback!
-
Yes, when the Esquire 2 is switched ON, it can charge a smartphone or tablet (or other USB-chargeable device that matches) through the special USB port. This function is available both when Esquire 2 is running on battery, and when connected to a charging port itself.Was this helpful? Thank you for your feedback!
-
Yes, on your computer, enter the IP address of the receiver in the internet browser. In the page that opens, it is possible to change the name.Was this helpful? Thank you for your feedback!
-
Yes, in the Harman Kardon Remote APP, it is possible to change the AURA's Bluetooth name.Was this helpful? Thank you for your feedback!
-
The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.Was this helpful? Thank you for your feedback!
-
Yes you can wash it if the fabric is dirty. But remember to close the USB cover.Was this helpful? Thank you for your feedback!
-
Is Bluetooth APT X streaming supported by the JBL Bar Studio, Bar 2.1, Bar 3.1, Bar 5.1 and Bar 9.1?The speaker uses Bluetooth version 4.2 but does NOT support APT X.Was this helpful? Thank you for your feedback!
-
Yes, but only with power on the Adapt. When it senses a signal on the analog aux input, the input ring will light up green automatically, and the signal will become available from the line output, for transmission with cable to e.g. an amplifier. It is important to note that there will be a slight delay in the signal that comes out of the line output jack, even if it does not involve any wireless functions.Was this helpful? Thank you for your feedback!
-
With different storage conditions and shipping durations, your power bank may go into deep sleep mode to protect the battery. If the power bank does not start charging your device when used for the first time, connect the power bank to a power source and charge it for 15-30 minutes, it should then work normally. If it still does not work, contact our customer service team and we will be happy to help you: https://support.infinitylab.com/#contactWas this helpful? Thank you for your feedback!
-
This unit is fully dust-proof, and can withstand continuous immersion in water (up to 1.5 meters / 4.9ft for 30 minutes).Was this helpful? Thank you for your feedback!
-
This product is rated IP67, which is different from IPX7. IP67 protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes. It is also resistant against dust. Dust accumulation around electronics can lead to hardware failure, so the IP67 rating is an extremely beneficial addition to this product.Was this helpful? Thank you for your feedback!
-
Our A2DP profile only support SBC Codec for ESQUIRE 2.Was this helpful? Thank you for your feedback!
-
Was this helpful? Thank you for your feedback!
-
The HKTS 65 is a new version of the HKTS 60, with minor improvements. Please select HKTS 60 in the menu.Was this helpful? Thank you for your feedback!
-
The amplifier has a signal sensor on the high-level (speaker level) inputs, so it is not necessary to use a trigger cable when input is high-level, and connected to the high-level inputs. However, low-level input signals through the RCA-phone input sockets do not activate a signal sensor, so use of a trigger cable is MANDATORY for low-level input signal use.Was this helpful? Thank you for your feedback!
-
Always get the latest Bluetooth driver version available for your Computer/PC/Laptop.
The driver (software) should support the following Bluetooth protocol, to be able to conference call from your Computer/PC/Laptop:
• HFP (Hands-Free Profile) driver to make conference calls from your speaker
During conference calls if there is intermittent volume and inconsistent audio quality, it is recommended to select "Stereo" in the Computer/PC/Laptop playback settings.
Was this helpful? Thank you for your feedback! -
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire/Focus 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
There can be differences in the internal hardware that also implies different firmwares. These products feature the same specifications and performance expectations. If the app does not inform you of any new updates, the firmware is current and the product is performing as designed.Was this helpful? Thank you for your feedback!
-
The InfinityLab power bank will not damage your device.
The InfinityLab power bank will deliver the power your device needs during charging, andd the InfinityLab power bank features auto protection against overheating and features overcurrent/overvoltage conditions.Was this helpful? Thank you for your feedback! -
All InfinityLab power banks are < 100Wh, so there are no restrictions for taking them onto flights as hand luggage (also known as cabin baggage or carry-on luggage).
However, power banks are not allowed to be carried in your hold luggage (also known as checked luggage).Was this helpful? Thank you for your feedback! -
The new Boombox 2 does not feature the Indoor/Outdoor Mode. With the first generation Boombox, the Outdoor Mode was loud, but lacking sufficient bass. The Boombox 2 has both improved bass and loudness to create the perfect balanced sound for all environments.
Was this helpful? Thank you for your feedback! -
The system features an automatic mute function that becomes active after 10 seconds of no signal activity. Since the output level varies greatly between different genres and recording levels, it is highly recommended to set your source volume levels above 4, or preferably at mid-level, then controlling the listening level using the volume control provided in the speaker system.Was this helpful? Thank you for your feedback!
-
To use our ESQUIRE2 with your Windows system, you'll need to find a Bluetooth driver that supports A2DP Audio codec. HARMAN do not have these and therefore you will need to contact your PC manufacturer.Was this helpful? Thank you for your feedback!
-
Often, hum is caused by a ground loop. This is a problem that is sometimes created when connecting two or more electrical components together. Sometimes the problem does not lie in any one particular unit, but in how they're connected. If your subwoofer is connected to a different wall outlet than your system, try to move the subwoofer plug to the same outlet. This may require an extension cord just for the trial. If it works, you can permanently move the sub or use an extension cord. However, if the hum you are hearing is coming from inside the sub, or if it is constant even when nothing is connected to the inputs of the sub, there is something wrong with the sub and you should bring it in for service.Was this helpful? Thank you for your feedback!
-
When using an Android device, you need to have location service active on your phone or tablet and make sure that you allowed "Google Home app" to use the phone or tablet location service. However, make sure your Wi-Fi router has UPnP enabled and that you do not use any network extenders while connecting the product.Was this helpful? Thank you for your feedback!
-
If you have updated the unit from a USB stick, performed a reset procedure and removed power from the unit completely for at least 10 seconds, and the BDS still does not work, please repeat the update process. You may want to re-download the update file as well. This should solve the issue, and we are sorry for this inconvenience.Was this helpful? Thank you for your feedback!
-
The quality of content depends on your Internet bandwidth. The minimum Internet speed is at least 25Mbps (megabit per second) or above for the best performance.
When using the LINK BAR to the WiFi router, always use 5 GHz WiFi band for highest performance at any time.
If you are still struggling with the quality of your content, then we have added an Ethernet port (LAN connection), which allows you to wire the LINK BAR for a steadier connection and performance.
More actionable advice:- Limit your device(s) at night or when you are streaming content that requires the best performance possible!
- Upgrade older product that could cause slow data transfer.
- Move devices that are capable of connecting to 5 GHz WiFi and leave "Legacy" product on 2.4 GHz only.
- Upgrade your router. Upgrading to a newer generation router is cheap and effective way to improve your home network in every way. It provides both a better Wi-Fi range and stronger signal.
- We are recommending that you go for a mid to high-level Wi-Fi router.
Was this helpful? Thank you for your feedback! -
Make sure your WiFi extender's name is not the same as that of your main WiFi network. Please use 5 GHz WiFi extenders only for best performance.Was this helpful? Thank you for your feedback!
-
If you have not received what you expected, please contact Customer Support as soon as possible, and no later than 2 days after receival of the parcel as we have a short window to process claims with our delivery partner.
Please note that you must keep all packaging, including the brown shipping box, while our Customer Support team is opening a claim with our delivery partner.
Was this helpful? Thank you for your feedback! -
When the secondary speaker gets out of range, audio disappears, but there is no indication that the transmission is out of range, other than silence. Once they get within range again, the front panel LED blinks a few times, indicating that connection has been re-established. During normal operation, random blinking can be experienced, which is an indication of the wireless link having recovered from interference.Was this helpful? Thank you for your feedback!
-
Please note that the AUX source supports a variety of input connections. By pressing the AUX button on the remote several times, the input toggles between the different audio inputs. Please press the remote control AUX button repeatedly, until the front display shows the correct input source. This should set the AUX input correctly, and you should have audio back in your speakers, to let you enjoy your Harman Kardon system.Was this helpful? Thank you for your feedback!
-
The ALLURE PORTABLE is not constantly looking for a wi-fi system. When you turn the unit on, it finds the wi-fi, connects, and begins working. When you move into another section with a different router, the ALLURE PORTABLE will no longer be connected. You will have to turn the ALLURE PORTABLE off and then back on again, so that it can find it's new wi-fi router.Was this helpful? Thank you for your feedback!
-
No, the Bluetooth name is fixed and not changeable. If you have multiple ESQUIRE2 in your Bluetooth list, and when activating one of them, it should be the "first" on your Bluetooth list.Was this helpful? Thank you for your feedback!
-
The first 105 files are registered right away. If you know that you have more files in the DLNA system, wait for close to a minute, while the BDS -75 / -77 registers the additional files. After a short while, it will begin counting until all files are registered, or until the maximum of 2000 files is reached.Was this helpful? Thank you for your feedback!
-
Please make sure that if you use 5GHz or 2.4GHz Wi-Fi, all your speakers are connected to either 2.4GHz or all are connected to 5GHz Wi-Fi to have the best performance.Was this helpful? Thank you for your feedback!
-
Our Control X Wireless speakers use Wi-Fi 2.4 GHz network to connect them. If there are any obstacles or people blocking the connection, it can cause interference. We suggest positioning the speakers on a high-level surface or shelf, to avoid any interference.Was this helpful? Thank you for your feedback!
-
Please place your AVR in full Standby by holding the Power Button for at least three seconds. Now, when you switch it ON again, the problem should have disappeared. Please note that Sleep Mode is not sufficient, you must use full Standby.Was this helpful? Thank you for your feedback!
-
Please make sure that your BDS is connected to the home network router also used by your smartphone.Was this helpful? Thank you for your feedback!
-
I have downloaded the HK Remote app and connected to my AURA Studio, but i do not see it in the app?AURA Studio is not supported via our app, and that means you cannot change any settings on it.Was this helpful? Thank you for your feedback!
-
The Harman AVR App controls your receiver through your smartphone, which communicates via your wireless home network. Please make sure that your AVR is properly connected to your network router, with cable for the smaller models. If you have no wireless home network, you cannot use the app.Was this helpful? Thank you for your feedback!
-
Please make sure that the audio out format is set to PCM in the TV. Dolby Digital or other surround formats will not work with the BTA 20 transmitter.Was this helpful? Thank you for your feedback!
-
Close and restart the Google Home app, or restart your phone. Start the Google Home app again, and the speaker should now appear.
Was this helpful? Thank you for your feedback! -
Typically when we are talking about projectors, they are normally installed in a place where the HDMI cable is too long, and the signal has a hard time reaching the AVR. It is also possible that the projector is not compatible with the AVR. To be sure it works with the AVR, please move projector closer and use a short HDMI cable. We recommend a cable that is 3 meters in length or less. If the projector works with the shorter cable, and you have no choice but to use a longer cable, you will need an HDMI repeater/amplifier/eq/booster (name varies depending on the manufacturer), to boost the signal so that it can make it all the way from the AVR to the projector.Was this helpful? Thank you for your feedback!
-
To use the Onyx Studio 2 with a PC or MAC, please make sure that you have the correct Bluetooth driver, that supports A2DP Audio Codec.Was this helpful? Thank you for your feedback!
-
This is sometimes a problem with wired connections to computers or NAS drives. There is no way to change this, unfortunately.Was this helpful? Thank you for your feedback!
-
• Please check whether you connected JBL DRG with your smartphone and head unit via Bluetooth before, then power off the head unit. • If you have, wait 2 minutes for JBL DRG to reconnect to smartphone after power on. This is because JBL DRG will automatically search for the head unit, first then the smart phone.Was this helpful? Thank you for your feedback!
-
When using the Boost TV as single device, it can have up to 3 Bluetooth connected devices attached. Once you are activating JBL Connect, it can only have one active Bluetooth source connected. To be able to use a different Bluetooth source, please turn off Bluetooth on your current connected device, and then press Bluetooth button on the Boost TV to enter pairing mode. Your new Bluetooth device are now connected and in control of the music.Was this helpful? Thank you for your feedback!
-
The correct button is the POP-UP button, located in the upper left corner of the upper big, square button. This will work as return button.Was this helpful? Thank you for your feedback!
-
The correct button is the POP-UP button, located in the upper left corner of the upper big, square button. This will work as return button.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00