How To
How To
1682 results
-
So your Pulse 4 got dirt on it, or even fingerprints, and you want to show off the device the best way possible.
Keep reading this article, and we will instruct you on how to clean the glass and device.
How to clean your speaker- Dirt and stains on your speaker can be cleaned under lukewarm running tap water.
- Use a soft cloth, preferably cotton, to clean the glass and to remove fingerprints. Hold the top part to avoid adding more prints to the glass part.
Contact our Customer support for more help and advice to keep your speaker top-notch!
Was this helpful? Thank you for your feedback! -
When the foam ear tips get dirty, it is recommended to clean them with a soft, dry cloth. It is not recommended to use water or wet wipes, doing so can affect the durability.
Important: Alcohol and other solvents should never be used as these may damage the surface of the ear tips.
Was this helpful? Thank you for your feedback! -
To clean your headphones, please follow the instructions below:
- Clean earpads and headphones with a soft, slightly damped cloth.
- Do not soak, submerge or allow moisture to enter near drivers and cable jacks.
- Earpads and cables can be purchased if worn out at www.Marklevinson.com.
- Use a polishing cloth to wipe down after use to remove fingerprints etc.
Was this helpful? Thank you for your feedback! -
To find out the software version, press and hold the [VOL- ] and [SOURCE] buttons simultaneously. The software version will scroll across the front display.
Was this helpful? Thank you for your feedback! -
To check the firmware version:
Press and hold the 'Preset 1' & 'Preset 5' buttons for more than 10 seconds.Was this helpful? Thank you for your feedback! -
The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.Was this helpful? Thank you for your feedback!
-
To charge, plug in the USB-C Connector and connect to a USB-C port (or USB-A port using the included adaptor).
Please note: you cannot listen while charging.
Was this helpful? Thank you for your feedback! -
To deliver 65W PD charging to your laptop, you will need a USB-C to USB-C cable supporting minimal 3A current.
To deliver 100W PD charging to your laptop, you will need a USB-C to USB-C cable supporting with E-Mark and supporting 5A current.Was this helpful? Thank you for your feedback! -
To enjoy the wireless charging feature for your InfinityLab power bank, below are the instructions on how to activate it.
- Press the power button (located on the front side, next to the battery indicator).
- Place your device on top of the power bank.
- The LED indicator on the side of the power bank will light up, indicating that the product is "charging."
Was this helpful? Thank you for your feedback! -
The surround speakers can be recharged through the USB-C connection, located on the side of the speaker. The speakers can be charged by docking them in the soundbar also.Was this helpful? Thank you for your feedback!
-
Ensure that your InfinityLab power bank is charged, then press the power button to trigger charging.
If nothing happens, please try to charge your power bank with a different charger and check the charging indicator next to the power button to see if the LEDs lights are blinking.
If it still doesn’t work, please contact our customer service team for help.Was this helpful? Thank you for your feedback! -
You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.
Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00