How To
How To
1674 results
-
As with all in-ear headphones, our range of True Wireless Stereo headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.
If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). This should remove the wax and resolve the volume/balance issues.
Was this helpful? Thank you for your feedback! -
The top panel LEDs are flashing because the OTA firmware update is in progress, the product should work after the upgrade is completed. It may have been caused by a previous interruption to an update.
It should be possible to resolve the issue by doing the following:
- Plug in the power cable and wait for at least 5 minutes for the Partybox Ultimate to complete the update.
- If the Partybox Ultimate stops flashing, but cannot power on, then perform a factory reset by pressing the two buttons below for more than 10 seconds: Moment (heart symbol) and Play (or through the JBL One app). After this has been done, press the Power button.
Was this helpful? Thank you for your feedback! -
The 12V trigger output can be used with a stereo 3.5mm jack cable. The 12v trigger signal is present in the ring/right-ch connection.Was this helpful? Thank you for your feedback!
-
Yes, it's 14 hrs with RGB off. You can also find the details on the box. Was this helpful? Thank you for your feedback! -
To configure the 7.1 Surround feature on your PC, please follow the guide below:
1. In the left corner on your screen right next to the Windows logo, click on the spy-glass to start a search on your PC.
2. Type in Sound --> then select Change System Sounds:
3. Make sure that your the Quantum Headphones is your Default Device for both Speakers ( Game ) and Earphone ( Communication device )
4. To configure the 7.1 Surround feature, right click on the Speakers --> then select Configure Speakers
5. Select 7.1 Surround and click on Next
6. Make sure that all boxes are selected, then click Next
7. Make sure both boxes are selected, and then click Next
8. Click on Finish. Now your Quantum headphones is configured for 7.1 Surround sound. The configuration will remain after rebooting PC or reconnecting headphones.
Enjoy your sound experience #SoundIsSurvival #DareToListen
Was this helpful? Thank you for your feedback! -
There are several ways to access the advanced settings. In the settings page, you can adjust settings for subwoofer, EQ and input sensitivity.
Make sure your PC or smartphone is connected to the same network as Citation AMP:
1. On a PC, go to the "Network" folder". There you can find an icon for the Citation Amp. Double click that, and you are taken to the internal webpage for advanced settings for your Citation Amp.
2. Or, in the Google Home app, go to settings for the Citation Amp. At the bottom of the page, you can find the device IP address. Copy and paste this address into your web browser, and you are taken to the internal webpage for advanced settings for your Citation Amp.Was this helpful? Thank you for your feedback! -
If you have already setup your JBL BAR 5.1 SURROUND with Google Home or AirPlay, you can now sign into your Amazon account via the JBL BAR Setup App. Just download the app and follow the instructions.Was this helpful? Thank you for your feedback!
-
High pass filter
When the subwoofer is connected, the main channels are "Small", meaning that there is a high-pass filter. This ensures proper blending with the subwoofer.
Crossover settingsThe Citation amp supports crossover settings in the range 50Hz - 120Hz. Default is 80Hz.
Multiple subwoofers?Only one type of subwoofer is supported at a time. Either with cable or wireless.
Was this helpful? Thank you for your feedback! -
This happens if you power up the subwoofer before connecting the right and left speakers. The system mutes to avoid potentially harmful pop noise. Just touch one of the volume up/down pads to unmute.Was this helpful? Thank you for your feedback!
-
No. Alexa notifications must be set up in the Alexa app and you can control the notification via Alexa voice only.
Was this helpful? Thank you for your feedback! -
Yes, you can use the universal command “ Stop”, “Dismiss”, “Cancel” and “Quiet” to stop the current music playback, alarm and timer.
Was this helpful? Thank you for your feedback! -
No, unless you have set up devices with both voice assistants, you cannot use Alexa to control devices you set up only in the Google Home app, or use Google Assistant to control devices you set up only in the Alexa app.
Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00