How To
How To
1676 results
-
For 5,000 models, the Max power output is 18W total.
For 10,000 models, the Max power output is 30W total.
It means when charging more than one device simultaneously, total max. output is 18W for 5,000 models and 30W for 10,000 models.
You can also check detailed power output information from the specification on the product page.Was this helpful? Thank you for your feedback! -
True Adaptive NC available on Tour One enables real-time monitoring of exterior surroundings and personal attributes like movement, hair, eyeglasses, and automatic adjustments to the NC performance and EQ.
If you don’t prefer the canceling performance's automatic change, you can get a fine-tuned canceling level by choosing “Everyday Mode” in the app.
Adaptive Noise Cancelling - available on Tour Pro+ TWS - listens to ambient environmental noises using external and internal mics then creates the inverse phase back to the listener creating the noise “canceling” effect.
The headphones also allow the listener to adapt or adjust noise cancellation through features like Ambient Aware and TalkThru.Was this helpful? Thank you for your feedback! -
Make sure to press the association button once. If by mistake you pressed it more than once, there is a good chance that association does not take place. Wait until the association process is completed, which takes about 2 minutes, and repeat the process.Was this helpful? Thank you for your feedback!
-
This can be caused by the charge arm reaching its thermal temperature cutoff. This is a safety feature to prevent a potential risk. For proper heat dissipation, always be sure to have the charging arm in the open position when your smart phone is attached.Was this helpful? Thank you for your feedback!
-
These holes are the microphones for the JBL LinkWas this helpful? Thank you for your feedback!
-
If your LINK BAR has 4 orange LED lights in the front, this means you have "muted" the microphone which is located on the top of the speaker.
To unmute the LINK BAR use the "switch" and the front LEDs will stop illuminating orange. Now you can use the hot-words to interact with the Google Assistant/Google Search (varies from country).
Privacy information:
We call our button the "PrivacySwitch" for the moments when you don't want the bar to listen for the hot words.
Google has high privacy rules, and one of them is not to share end-user data with any third-party apps.
Was this helpful? Thank you for your feedback! -
For InfinityLab charger, the recommended operating temperature is between 0-45°C.
Our chargers provide auto protection against overheating as well as overcurrent/overvoltage conditions.
Therefore, when the operating temperature is outside the range, this charger will auto adjust the output powers to protect itself and your devices.Was this helpful? Thank you for your feedback! -
Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.Was this helpful? Thank you for your feedback!
-
Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.Was this helpful? Thank you for your feedback!
-
This is the charging indicator LED. I lights up red when the headphone is charging, and goes dark when charging is complete, or if no charging takes place.Was this helpful? Thank you for your feedback!
-
As explained in our Owner's manual, it will adjust the sound to match the placement of your Soundbar, wall or table. When against a wall, the sound reflection will be different than when on a table. This button adjusts the tonal quality to give you the best audio results in either setup.Was this helpful? Thank you for your feedback!
-
Verify your TV supports the ARC feature.Make sure you enable the external speakers/ARC/digital audio output on your TV, this varies by TV manufacturer. Set the AVR1x1S to the TV input. Go into the AVR menu settings and under System Settings, make sure Audio Return Channel is set to Auto and set the TV Control to on.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00