How To
How To
1674 results
-
Switch the headphone ON, then press both volume buttons (VOL + and VOL-) at the same time, and hold them for 5-6 seconds. The headphones are now reset to factory default.Was this helpful? Thank you for your feedback!
-
Here is the pairing procedure between a K915 headset and a new transmitter box: 1. Power off the headphone. 2. Power off the transmitter. 3. Press and hold the power button on the headphone until the “Signal” LED is flashing, and a beep sound can be heard. 4. Power on the transmitter. 5. After a short while the “Signal” LED will light constantly (stop flashing) and the pairing is complete.Was this helpful? Thank you for your feedback!
-
Please refer to the owner's manual for AVR 151 or 151S. The procedure is explained there. The remote control contains a number of pre-programmed command sets that can be activated to control TV sets, disc players and other devices of various brands.Was this helpful? Thank you for your feedback!
-
The JBL Quantum TWS works on most mobile devices, however, some mobile devices restrict the utilization of it's audio and microphone functions via USB-C causing there to be no audio or microphone operation. In these cases we recommend connecting to the earbuds using their Bluetooth connection.Was this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
You can send any 4k video signal into the HDMI inputs of your AVR, and it will be sent to your TV screen from the HDMI output, either in 4k or 1080p. Sometimes it may be necessary to switch off the TV set, then switch it on again, to activate a new "handshake" between the devices, in order to open for the 4k signal, if normal HD 1080p signal was the last signal used. Please note that not all 4k signals can be viewed. Many streamed videos from Youtube will work, as will any 4k material that you have recorded yourself, and many TV boxes will work also. However, HDCP 2.2 protected material will not be shown in 4k, but will be converted to full HD 1080p signals, because these AVRs do not support HDCP 2.2 digital copy protection. HDR is not supported.Was this helpful? Thank you for your feedback!
-
With no signal, the BDS will turn itself off after the number of minutes you have previously set. When connected with optical cable to an external source, and with signal present, it will not turn off, even if the Auto Turn Off is on.Was this helpful? Thank you for your feedback!
-
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
Each speaker, adaptor and phone/tablet connects to your home Wi-Fi network, just like any other Wi-Fi produce you own. You can then stream any music from your phone/tablet to any Omni speaker or Adapt over your home networkWas this helpful? Thank you for your feedback!
-
JBL QuantumSURROUND takes up to 8 channels of audio, and recreates a multi-channel setup—including overhead channels—as measured inside one of JBL’s listening rooms. You’ll hear the multi-channel mix as if you’re right in the middle of the game.Was this helpful? Thank you for your feedback!
-
Let's say you have 4 LINK devices in your home and you start your day with "OK Google, How is the weather?".
All of your devices will "light up" and start listening to the command. However, only one of the speakers will give you the information (if they are under the same account).
The speaker with the best microphone reception will respond with an answer.
Please note: if you have muted all speakers or 3 out of 4 are muted, then only one will respond and the rest will not react.
If all speakers are muted, all will be silent.Was this helpful? Thank you for your feedback! -
For models E40BT and E50BT Connect the first headphone by BT to your mobile device Tap the ShareMe button once Tap the ShareMe button on the 2nd headphones twice ( ! ) The headphones will connect to each other. When changing volume on source device, or BT connected headphones, the volume will only change on THAT headphone ( and in some cases the source device, like iOS devices and newer Android ), not on the one connected via ShareMe. When changing volume on a via-ShareMe-connected headphone ( 2nd ), it will not change volume on source device, or on the BT-connected headphone. To sum up, both headphones have their individual volumes. For Everest models ( not ELITE ). Connect the headphones by BT to your mobile device Put the 2nd device ( speaker, headphones as long as they have Bluetooth ) in "BT discovery mode" Press the ShareMe button on the Everest headphone ( button marked with a little "s" ) The Everest will connect to BT device. (Please note that you may not be able to pair from the Everest to the Everest Elite models, or if you can pair, you may have dropouts in sound). When changing volume on source device, or Everest, the volume will only change on the Everest ( and in some cases the source device, like iOS devices and newer Android ), not on the device connected via ShareMe. When changing volume on via-ShareMe-connected BT device ( 2nd ), it will not change volume on source device or Everest. Please note that it is NOT possible to use ShareMe if you are listening to analog signal via cable. Bot the E-series and the Everest models will switch off the Bluetooth circuits as soon as you insert the audio cable, so re-transmission is not possible.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00