How To

Support Overview / How To

How To

1674 results

Sort

Page size

How do I see when my JBL E45BT or E55BT is fully charged?

While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.

Was this helpful? Thank you for your feedback!
How do I see when the noise cancelling battery of AKG N20NC is empty?

When less than one hour's capacity is left, the red diode will blink. It will eventually stop blinking, when all power is gone.

Was this helpful? Thank you for your feedback!
How do I set up my Adapt so my existing equipment can play stereo?

In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.

Was this helpful? Thank you for your feedback!
How do I setup my AVR's Zone II?

At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Everest 310/710 headphones?

To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Everest 750NC?

To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Synchros E30?

The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the T205?

Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.

Was this helpful? Thank you for your feedback!
How do I start the product for the first time?

The JBL product is in a deep sleep mode, which it is to prolong the lifetime of the battery. Connect the case to a charger for about 2 seconds to wake the product up and take the earbuds out from the case. Once you put the earbuds back in the case, it's ready to pair through Bluetooth.

Was this helpful? Thank you for your feedback!
How do I switch the enhancer sizes?

The best way to remove the enhancer from the ear bud is to gently pull back the outer rim of the enhancer that is located around the base of the ear bud. When replacing the current enhancers with a different size, please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. The LEFT enhancer will feature the square cut out that allows you to receive your Heart Rate reading. It is important that the small digital square on the ear bud is fully exposed and the enhancer cut out is placed around it and not over it. If the enhancer is not attached properly, you will hear the audible voice stating that it cannot receive an accurate reading on your heart rate and you will need to readjust the enhancer.

Was this helpful? Thank you for your feedback!
How do I turn off my E45BT or E55BT?

The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.

Was this helpful? Thank you for your feedback!
How do I turn off my internal TV speakers?

Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.

Was this helpful? Thank you for your feedback!
How do I turn off my internal TV speakers?

Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.

Was this helpful? Thank you for your feedback!
How do I turn off the device?

Press and hold the center button for 3-5 seconds until the audible voice states “power off” you will briefly see a red light before it completely powers down.

Was this helpful? Thank you for your feedback!
How do I turn off the Google Assistant on the JBL Everest 310GA and 710GA?

It is not possible to turn the Google Assistant feature off on the headphones, but if you turn off GA on your phone, the headphones won't trigger. On the Everest GA models, the Google Assistant feature is in fact than an extension of your phone, so once you connect to your phone via BT, when you touch the right ear pod, it commands your phone to open the "Hey Google" command.
The only way to stop that from happening is to change the Google settings on your phone to deactivate Google Voice Match, or deactivate Google Assistant entirely.

Was this helpful? Thank you for your feedback!
How do I turn on and pair the UA headphones with my device?

To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the UA WIRELESS headphone. Once you select that option, the audible voice should state, “connected”.

Was this helpful? Thank you for your feedback!
How do I turn on pairing mode?
To activate Bluetooth pairing mode, please follow these steps:
- Press the Bluetooth button on the bottom of the right headphone.
Now find the Headphone in your Bluetooth device settings and select it to connect.
Was this helpful? Thank you for your feedback!
How do I turn SoundShift On?

1. First pair your phone to the Boost TV. You can test this by streaming music to the product. 2. Then press the TV button to switch to the TV sound. Press the TV button again so the LED light is blue--Blue LED means that SoundShift is ON. 3. When you press PLAY on your phone, then you will hear your Bluetooth audio break in over the TV sound. This confirms that SoundShift is working. 4. Simply press SoundShift button again, this will now turn OFF the SoundShift. Now you can watch TV without any interruption from Bluetooth devices.

Was this helpful? Thank you for your feedback!
HOW DO I TURN THE ACTIVE NOISE-CANCELLING / AMBIENT AWARE modes ON?

Your headphones arrive in ANC OFF mode. To switch between modes, press the red ANC button on the left ear cup, this will cycle between OFF / ANC / AWARENESS. Via the app, you can select the default ANC of HIGH, ADAPTIVE or LOW and the default AWARENESS level of VOICEPASS or AMBIENT.

Was this helpful? Thank you for your feedback!
How do I uninstall JBL QuantumENGINE software?

You can go to the Control Panel> Programs and features to uninstall JBL QuantumENGINE.

Was this helpful? Thank you for your feedback!
How do I upgrade my JBL QuantumENGINE if there is a new version?

You will need to navigate to the System section, and if the software button is highlighted with "Download Software", please click on the button. When the download is completed, you can click "install update" to install latest version. Make sure you restart your computer once the upgrade is finished to ensure all changes are applied.

Was this helpful? Thank you for your feedback!
How do I use Amazon Alexa with my headphones?

- Single tap the left ear cup to engage Alexa.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices and select ‘Use Alexa’.

Was this helpful? Thank you for your feedback!
How do I use my UA Headphones with Record?

Connect your headphones and start a workout using UA Record's heart rate zone tracking. Track your current heart rate zone so you know when to rest or power up, while also viewing your total heart rate distribution throughout each training session. Know your current, average, and peak heart rate. You also have the option to hear your stats read aloud during a workout. With UA Record, you can customize what feedback you hear by setting your stats, frequency, voice, and volume.

Was this helpful? Thank you for your feedback!
How do I use the Google Assistant with my headphones?

- For more information on what your Google Assistant can do, visit: assistant.google.com/platforms/headphones

Was this helpful? Thank you for your feedback!