1. Enter pairing mode and connect to "device 1" (Phone, tablet, etc.)
2. Enter pairing mode again, and "device 1" will disconnect.
3. Connect to "device 2" and turn the headphone off.
4. Turn headphone on, and headphones will automatically connect to "device 1" and "device 2" simultaneously.
5. Pause one device and play from the other to swap the headphones connection.

NOTE: Maximum number of devices connected to the headphones at any given time is 2 source devices (Phone, tablet, etc.).

How to pair an Enchant Subwoofer with your Enchant bar

1. Go to the back of your Enchant soundbar (800 or 1300)
2. Press the "Subwoofer pairing" button for 2 seconds.

3. In front of your Enchant display, it will say "Subwoofer pairing"
4. Go to the back of your Enchant subwoofer.
5. Press the "Subwoofer pairing" button.

6. The small LED indicator will start to flash rapidly and when the connection is successful, it will be a steady light.

You now have more bass performance and can enjoy deeper richer sound!

1. Power on your Enchant 800 or Enchant 1300 Soundbar. 2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar. 2.1. Press the dedicated source button on top of your Enchant soundbar source 2.2. Press the source button until you see "Bluetooth" in the front of the Enchant display. 3. The second option is to use the Remote control included with your Enchant soundbar. 4. Press the "BT" button on your Remote control. 5. The display will show "Bluetooth pairing". 6. Go to your Bluetooth settings menu on your mobile device. 7. Enable Bluetooth and connect to your Enchant 800 or Enchant 1300 Soundbar.

If you want to add more depth and bass to your LINK BAR, we have a dedicated subwoofer (not included with the LINK BAR) that you can purchase!

Pairing the Subwoofer is very simple:
1. Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly.
2. Press the “Subwoofer Pairing” button on the SW10 subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly.
3. Press the “Subwoofer Pairing” button on LINK BAR, the LED indicator on the LINK BAR blinks rapidly
4. If successful, the pairing LED indicator on both subwoofer and LINK BAR will be a steady white LED light. If pairing fails, the sign on the subwoofer blinks slowly.
5. If the pairing fails, repeat the steps above. If you are still experiencing problems, please try to switch off all wireless devices in the home (such as routers, TV sets with wireless function, telephones, computers, etc.), then try again. It may be overcrowding on the 5GHz frequency, which often causes problems. By eliminating all other wireless activity, this will help space for the LINK BAR to establish its connection. You now should be able to pair without problems. Once pairing is complete, you can switch your devices on again

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.

You will see a notification in the recommendation option on your TV screen when there is an upgrade is available.

The system will download the firmware and apply the update after your confirmation.

You can also manually check for updates. Go to the settings menu and select “About” followed by “System Update.”

Before starting, remove any interference that might be blocking the Soundbar side-firing speakers. Any ambient noise or sounds that could disrupt the calibration needs to be out of the room. After completing the initial setup in Google Home app, select the Settings screen on the touch display of the product. Select "Speaker Setup", and then "Calibration". Follow the directions in the display to perform the calibration. A series of tone sweeps/chirps will play in all directions, and the calibration process will finish within approx. 30-40 seconds. Calibration is done! In case you are moving the soundbar you will need to calibrate the sound again.

Prerequisites:
− Make sure that your room is quiet;
− Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
− Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.

The calibration is done in two steps: Listening zone & Speaker position

Calibrate the listening zone

1. Place the detachable rear speakers beside your seating position.

2. On the remote control, press and hold HDMI until “1-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “1-DONE”: Calibration of the listening zone is completed successfully.

Calibrate the speaker position

1. Place the detachable rear speakers in your desired location.

2. On the remote control, press and hold HDMI until “2-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “2-DONE”: Calibration of the speaker position is completed successfully.
3. To select suitable surround sound level, press repeatedly to switch between high, low or middle (default).

NOTES:
− During calibration, all buttons on the remote control are disabled except for STANDBY and HDMI.
− “SETUP FAILED” is displayed if calibration failed.

This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.

USB Stick

1. Get an empty stick with speed of 2.0.
2. Make sure it is formatted with FAT16 or FAT32.
3. Your Music files can only be:  (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
4. The Partybox supports up to 8 subfolders.
5. It will be played in alphabetic sequence with main folders first then subfolders.
6. To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.

Playing music over Bluetooth connection is very simple to do:

1. Short press the dedicated Bluetooth button on the LINK BAR.
2. Go to settings on your phone.
3. Find Bluetooth and enable it.
4. Select the JBL LINK BAR in your device list.
5. You are now paired and ready to jam your favorite music!

If you are experiencing issues with the speakers turning off automatically while in use, try the following to resolve the issue (PC only):

• Enter 'Device Manger' in the Windows search bar (the magnifying glass icon at the bottom left of the taskbar in Windows 10), it should now appear in the search results under Control Panel.
• In the Device Manger list, navigate to your Universal Serial Bus Controllers, then select the 'USB Root Hub' device, right click it and select Properties.
• In the 'USB Root Hub' Properties select 'Power Management' from the options at the top, now turn off the setting 'Allow the computer to turn off this device to save power'.

The steps above may also solve issues relating to audio dropouts.