JBL Wireless Microphone Set

Specifications

General Specifications

Distance between transmitter and receiver :>10m

Polar pattern: Cardioid

Frequency response: 65 Hz-15kHz

Signal-to-Noise(S/N) ratio:60 dBA

UHF frequency band:470-960MHz(depends on SKU)(EU 657-662MHz)

THD:0.5%, typical

Dynamic range:100 dB A-weighted, typical

Transmitter transmitting power:<10 mW, typical

Receiver input:1/4"(6.3 mm) unbalanced

Receiver maximum Output Level:-13dBV,typical

Receiver rechargeable Battery:Lithium-ion Polymer 3.7WH(Equivalent to 3.7V, 1000mAh)

Receiver charge time :2 hours @5V/1A

Receiver battery Playtime:Up to 6 hours

Microphone battery: 4 x AA alkaline (included)

Dimensions

Dimensions (W x H x D): Microphone Φ50 x 233mm/1.95"x 9.16"; Receiver 70mm x 80mm x 20mm/2.75"x3.14"x0.78"

Weight: Microphone 235g/0.52lb;Receiver

Sing along with incredible voice clarity and Original JBL Pro Sound

It’s time for you to take center stage. JBL wireless mics deliver Original JBL Pro Sound with crystal clear vocal clarity and detail. Sound your best and hit the high notes with no distortion or delay. Just plug the wireless dual-channel receiver into your speaker, turn on the mics, and you’re ready to shine. Easy replaceable AA batteries, so you can belt every note until the sun comes up. Time for a duet? You’ll hear both mics blended perfectly through your speaker. Get ready for the spotlight.

High vocal quality and Original JBL Pro Sound

The crystal clear clarity from the JBL wireless mics means no jamming, delay or distortion. Your voice will sound on point, with the backing of incredible Original JBL Pro Sound.

Rechargeable UHF dual channel wireless receiver

There’s no need to fly solo, unless you want to take center stage of course. Connect two wireless microphones together and hear both voices blended perfectly through the speaker for up to 6 hours of playtime.

Plug and play

When you want to be heard, you want to be heard now. The JBL wireless mics have a super simple setup. Just turn on the receiver and wireless microphone and you’re good to go instantly.

Microphones come with replaceable AA batteries

JBL wireless mics come with easy replaceable AA batteries, so get your groove on all night long.

Best performance with JBL PartyBox speakers

Use JBL wireless mics on a speaker with a mic input, but for the best experience, add-on to any of the JBL PartyBox speakers with a mic input.

FAQs & How-Tos

4 results

Sort

Page size

Are the JBL Partybox Encore and Partybox Wireless Mic Compatible?

While the Partybox Encore does not have a Microphone Input, it does have an internal receiver for the wireless microphone that comes with the product.

It is possible to pair one of the microphones from the Partybox Wireless Mic * (sold separately from the Partybox Encore, containing 2 x Wireless Microphones and 1 x Receiver/Dongle for connection with 6.3 mm microphone jack inputs) - however, a maximum of 2 wireless microphones can be connected to the receiver at a time.

As an alternative, a spare part accessory is available (dependent on stock levels), which includes just 1 x Microphone for Partybox Encore - search for the aforementioned product name or "FG7261JMJ100114" in our online store.

To connect an additional Wireless Microphone to the Partybox Encore, follow these steps:

Switch off the Partybox & both microphones.

Once off, switch on both microphones only, then switch on the Partybox and both microphones should connect to the receiver.

If not, please try the same instructions as above expect with a Factory Reset (Press and hold the "Play" and "Light" buttons for > 10 seconds) instead of the restart above, then follow the microphone pairing procedure:

1. Turn off the speaker.

2. Make sure that the distance between the new wireless microphone and speaker is within 1 meter. Turn on the microphone.

3. Turn on the speaker. The microphone will pair and connect with the speaker automatically within 3 minutes.

*Please note that regarding the older version of the JBL Partybox Wireless Mic - the JBL Wireless Microphone Set - the microphones are not compatible with the Partybox Encore whatsoever, as they use UHF instead of 2.4 GHz for communication between the microphones and receiver (and the Partybox Encore does not have a Microphone Input).

Was this helpful? Thank you for your feedback!
How to Connect the Wireless Microphone Set to a Partybox

To successfully connect the JBL Wireless Microphone Set to a Partybox, connect the supplied 6.3mm jack dongle to the Partybox's Microphone Input. Now turn on the dongle and the Partybox. The dongle's Power button light should stay lit, if the light turns off or does not stay lit it is off and needs to be charged with the provided USB cable.*

Now turn on one or both microphones as required and increase the Mic volume and gain to the desired level. The LED screen will show a channel number 'CH-1', 'CH-2', etc. The channel number is not changeable manually, and may change between power cycles, but all channels will connect automatically to the dongle. If the LED screens do not show a channel number, the batteries in the microphones need to be replaced.

*Charging the dongle while in use is not recommended and will likely cause unwanted interference.

Was this helpful? Thank you for your feedback!
TWS Mode Capabilities and Restrictions

You can connect two of the same Partybox models (e.g. 2 x Partybox 310, or 2 x Partybox 100) together in TWS Mode by pressing and holding the Bluetooth button on both speakers for 5 seconds, or by pressing the dedicated TWS buttons on the rear panels of both speakers on the Partybox 110, 310 and 710. It is possible to pair two different Partybox models together using a wired connection (e.g. 1 x Partybox 310 and 1 x Partybox 100). It is also possible to pair two Partybox different models wirelessly in Party mode, however this is only possible with the newer Partybox models - the Partybox 110, 310 and 710. The Partybox 200 & 300 can be paired in TWS mode as they are the same model apart from the presence of a battery in the Partybox 300. If you connect an instrument or microphone to one Partybox speaker while using TWS, the instrument or microphone connected to one speaker will be reproduced by this speaker alone. You will not hear the instrument or microphone in both speakers. If it is necessary to have instruments reproduced by two or more PartyBox speakers, it is possible to use an RCA or aux cable – connected from the RCA, aux or daisy chain outputs on the speaker that the instrument or microphone is connected to, wired to the RCA, aux or daisy chain input of the secondary speaker. Alternatively a small mixing console can be used - connecting audio sources to this mixer and sending the mixed audio signal to the speakers with a wired connection.

Was this helpful? Thank you for your feedback!

Wireless Microphone Information

The JBL Wireless Microphone set allows 2 x wireless microphones* to be connected to any Partybox model ** through the use of a dongle connected to the Mic input. Additionally, a 3rd wired microphone - like the JBL PBM100 Wired Microphone, can also be connected to the switchable Guitar/Mic 2 input (only available on some Partybox models). This will also work when using the non-switchable Guitar input on other Partybox models - however, this will bypass the karaoke effects including echo for the connected microphone and would generally have a slightly different sound character/timbre to a microphone connected to the Microphone input.

*This includes the Partybox On-The-Go, a maximum of 2 wireless microphones can be connected and used simultaneously. The standard bundled Partybox On-The-Go microphone can only be connected to the Partybox On-The-Go that it came bundled with, it also cannot connect wirelessly to any other Partybox models or portable speakers other than the Partybox On-The-Go that it came bundled with. Only one standard, bundled Partybox On-The-Go wireless microphone can be connected at a time, unless the JBL Wireless Microphone is purchased (sold separately), a spare part will only work as a replacement, not simultaneously.

PartyBox Model	Mic Arrangement	Ports Used	MAX
** Encore	1 Wireless (pre-paired, included) OR 2 Wireless (sold separately, second microphone needs to be manually paired as described in Owner's Manual)	N/A - Wireless (pre-paired, no Wired Microphone port)	2
100/110/Encore Essential	1 Wired OR 2 Wireless (Wireless Microphone Set must be used, sold separately)	Mic Port	2
200	1 Wired OR 2 Wireless (Wireless Microphone Set must be used, sold separately)	Mic Port	2
300	1 Wired OR 2 Wireless (Wireless Microphone Set must be used, sold separately)	Mic Port	2
310/310 MC*/710/Ultimate	1 Wired AND 2 Wireless (Wireless Microphone Set must be used, sold separately)	Mic Port AND Mic/Guitar Port	3
1000	1 Wired OR 2 Wireless (Wireless Microphone Set must be used, sold separately)	Mic Port	2
On-The-Go/On-The-Go Essential	1 Wired AND 1 Wireless (pre-paired, included) OR 2 Wireless (Wireless Microphone Set must be used, sold separately)	Mic Port AND N/A - Wireless (pre-paired) OR Mic Port (pre-paired microphone will not work simultaneously when dongle used)	2 OR 2

* Partybox 310 MC - is a standard Partybox 310, which comes bundled with 1 x Wired Microphone (PBM100).