JBL Control X Wireless
Powerful, expandable wireless stereo Bluetooth® speakers for home or on-the go
Sold from 2016 until now
Getting started with your JBL Control X Wireless
Register your product
Do you own this product? Register it here! And claim your warranty or service easily
Register nowDocuments & Downloads
Specifications
- Finish
- Graphite / White / Red
- Rated Power
- 30W per channel RMS (AC mode)
- Signal-to-noise ratio
- >75 dB
- Power supply
- AC 100-240 VAC, 50-60Hz
- Battery Type
- Lithium-ion Polymer (7.4V, 2600mAh)
- Battery Charge Time
- 2.4 hours @ 0.5C
- Playback Time
- Up to 4 hours (varies by volume level and audio content)
- Bluetooth® Transmitter Power
- 0-4 dBm
- Bluetooth® Transmitter Frequency Range
- 2.402 – 2.480 GHz
- Bluetooth® Transmission Range
- Up to 10m (from source)
- Speaker Range
- Up to 30m (between primary and secondary speakers)
- Dimensions
- 9-1/4" x 6-1/2" x 6-1/4" (235mm x 165mm x 159mm)
- Frequency Response
- 62Hz - 20kHz (-6db)
- Weight (kg)
- 2.95 kg
- Weight (lb)
- 6.5 lbs
- High-Frequency Transducer
- 1" (25mm) CMMD® Lite dome tweeter
Rock the house inside and out
Take your favorite music, movies, TV shows, or games to the next level with the award-winning JBL Control X Wireless speakers. This portable Bluetooth® speaker pair outputs immersive stereo sound without any wires or cables between each speaker. These compact speakers were designed to provide mind-blowing power and performance to any room in your home. And when it’s time to take the party outside, the rugged design is well-equipped to handle any gathering or event. If you require a wider soundstage, simply add an additional pair of Control X Wireless speakers (sold separately) for simultaneous playback on up to 4 speakers.
Stream via Bluetooth® or use the rear 3.5mm input for stereo or mono playback. Unlike other stereo speakers, there’s no need for an interconnect cable or wire between each speaker. Use one or both speakers inside or outside your home, without the restrictions of a transmitter or wired cable connection.
Be the life of the party with 30 watts of uninhibited power from each speaker. While other powered speakers distort at high levels, JBL Control X Wireless speakers provide clean, undistorted audio at any volume. Make a statement by being heard loud and clear.
Hear the truth. This proprietary waveguide technology provides the same lifelike stereo imaging and detail found in the world’s most renowned studios, clubs, concert halls, theaters, arenas, and stadiums. Simply put, JBL Control X Wireless speakers were engineered to put the performance right in front of you.
We are all about the bass. JBL has a rich history in transducer and acoustic design and it shows with Control X Wireless. We intentionally use a stiff cone material that works in conjunction with our rear patented Slipstream-tuned port. This results in tight, block-rocking beats no matter the genre.
JBL Control X Wireless speakers were built to bring out the best in your music no matter the space. These speakers will rock your home, dorm, or commercial space, along with any street, park, campsite, beach, or social event. The rear port also serves as a carrying handle.
Allows up to 4 Control X Wireless speakers to work together to provide expanded, super-sized stereo or summed mono coverage to a wide area without the need for additional wires between each speaker (additional pair sold separately).
FAQs & How-Tos
16 results
-
No. Although the Control X Wireless have a rugged exterior and are portable, they are not all-weather speakers. Any direct exposure to harsh weather condition (rain, snow, extreme hot/cold temperatures) will damage the speakers.Was this helpful? Thank you for your feedback!
-
No, you can only have one activate device connected to the speaker. Please un-pair your current Bluetooth device, then connect with another device if needed.Was this helpful? Thank you for your feedback!
-
Please note that although the Wireless version of Control X does have a threaded insert for brackets, JBL offers no brackets. The brackets for the Control X passive model cannot be used with the wireless version. Brackets for the wireless version must be custom made.Was this helpful? Thank you for your feedback!
-
Yes, on the master speaker (the one with playback buttons), simply press the Reverse and Forward Play buttons at the same time for 3 seconds. Please note that after you have performed the reset procedure, master and secondary speakers are no longer connected. Go to the owner's manual page 4, the section "speaker association", to pair the secondary and master again.Was this helpful? Thank you for your feedback!
-
Yes, that’s the best part about this speaker, there are so many options. Besides streaming over Wi-Fi, the JBL Control Xstream also offers a Bluetooth connection and an AUX inputWas this helpful? Thank you for your feedback!
-
No, the connection between our Control XT wireless speakers are established through Wi-Fi connection, running on 2.4 GHz network. The only time you will use Bluetooth, is when you connect to the primary speaker and start streaming music.Was this helpful? Thank you for your feedback!
-
Random flashing is an indication that the wireless link between primary and associated speakers was lost and recovered. If this happens too often, it may be caused by interference in the 2.4 GHz ISM band, caused by overcrowding of the band. Sometimes it helps to change location of the speakers, or to shut down other 2.4 GHz devices.Was this helpful? Thank you for your feedback!
-
Look at the back of the primary speaker, which is the one with pause/play and volume controls. You will see a switch called "mode". This switch can be in either S or P position. S stands for Secondary, P stands for Primary. Switch to Primary, and your speaker will now open Bluetooth and will accept analog signals. (The Secondary position is used for systems where four speakers are in use, since only one speaker can act as primary speaker.)Was this helpful? Thank you for your feedback!
-
Our Control X Wireless speakers use Wi-Fi 2.4 GHz network to connect them. If there are any obstacles or people blocking the connection, it can cause interference. We suggest positioning the speakers on a high-level surface or shelf, to avoid any interference.Was this helpful? Thank you for your feedback!
-
When the secondary speaker gets out of range, audio disappears, but there is no indication that the transmission is out of range, other than silence. Once they get within range again, the front panel LED blinks a few times, indicating that connection has been re-established. During normal operation, random blinking can be experienced, which is an indication of the wireless link having recovered from interference.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00