JBL Tune 125TWS

Documents & Downloads

FAQs & How-Tos

9 results

Sort

Page size

Cleaning Instructions for Re-establishing Charging

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

Was this helpful? Thank you for your feedback!
aptX Audio Codec Support

This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.

Was this helpful? Thank you for your feedback!
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.

Was this helpful? Thank you for your feedback!
How to avoid Bluetooth Interference or Interruptions

• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.

• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.

• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.

• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.

• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.

• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.

Was this helpful? Thank you for your feedback!
How to clean your earbuds
Use a clean cotton swab slightly moistened with alcohol to:
1. Remove earwax and dirt from the ear tips on your earbuds.
2. Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
3. Clean the grooves on the cover and at the bottom of the charging case.
After cleaning, make sure the charging case and earbuds are dry before putting the earbuds back into the charging case.

TIP: We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.
Was this helpful? Thank you for your feedback!
How to Factory Reset True Wireless Stereo Headphones

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

Was this helpful? Thank you for your feedback!
How to Turn off your TWS Headphones

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

Was this helpful? Thank you for your feedback!
Is Volume Control Supported?

This headphone does not feature volume control. You must manually control volume from your device.

Was this helpful? Thank you for your feedback!
Waterproof Information

This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.

Was this helpful? Thank you for your feedback!