You can enjoy streaming your favorite music over WiFi to your JBL BAR 9.1 Surround by adding it to your network. Turn on your soundbar. Download the Google Home app to your phone. Enable Bluetooth and Location services on your device. Open Google Home app Follow the instructions given in the app. You are now connected to your WiFi network and can enjoy streaming music to your system. The soundbar will now be able to automatically update, to make sure the performance is the best at all times.

Citation One and Citation 100

1. Press the Bluetooth icon. Located on the top panel.
2. Go to -menuMake sure Bluetooth is 
3. Find your Citation speaker and connect.

         

4. You are now connected and ready to play music over Bluetooth, Enjoy!

Citation 300, 500, Bar and Towers

1. Swipe up on the display to find Bluetooth icon.
2. Tap Icon will light up Go to -menu Make sure Bluetooth is
3. Find your Citation speaker.

        

4. You are now connected and ready to play music over Bluetooth, Enjoy!

To connect any device to your headphone, please follow these steps below:

1. First, hold the power ON/OFF button down for >5 seconds.
   1. The status light will pulse white when the headphones are in pairing mode.
2. Next, release the power ON/OFF button.
3. Next, go to the Bluetooth settings on your source device (Smartphone, tablet, etc.).
4. Find the Mark Levinson No 5909 headphones in the Bluetooth list, and tap to connect.
5. A solid white light indicates that you are connected to the headphones.

Enjoy your sound experience!

To control the Light show on your JBL Partybox device, simply press the dedicated "Light show" button located under the Bluetooth icon. There are 3 different light shows available when toggling through them, select your favorite one and have a blast. There is no app developed to control or modify these settings, all settings have to be done on the Partybox device.

Bluetooth Pairing

1. Press the button on the Partybox to start the pairing process.
2. Grab your device.
3. Go to settings --> Bluetooth --> Enable Bluetooth -->
4. Find the Partybox speaker you want to establish a Bluetooth connection to.

        

5. You now have a successful connection and can stream your favorite music.
   1. NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
   2. To stop Bluetooth broadcasting then insert a USB device.

In our latest update for Citation, we added a couple of new features.
We are going to talk about our new programmable preset feature.

With this feature, you can add a voice command such as "Turn off the lights in the Bedroom" or "Play my playlist Rock road classic" without using your voice.
Once you have recorded the action, you will see an icon on your Citation display. Tap on this specific recorded command, and the Citation will do all the magic for you!

Enough of what it can do, let us create a preset:

1. Scroll down on your Citation Display to you see "Voice presets."
2. Press on the + sign.
3. Say your command: Play Radio FM
   1. Do not use "Hey or OK, Google at this point."
4. Press the "V" icon after the command is finished.
5. Select an icon.
6. Your Preset is now ready, tap it to give it a try.

To delete any presets.

• Press and hold down the preset.
• A menu will appear, hit the "TRASHCAN" icon.

If you have two of the same model Google Assistant speakers, you can create a stereo speaker system.

How to create a stereo pair...

1. Open the Google Home app
2. Find the speaker you want to setup in stereo pair
3. Find the speaker/room
4. Tap on Settings
5. Go to Sound Settings
6. Find the Speaker pair
7. You are now entering the setup page Tap
8. Find your speaker under the Pair with list and tap.
9. Move the speaker to be Left or Right side and press
   1. You can tap on Play sound to identify which speaker it is.
10. Find a name for your Stereo pair
11. It takes a minute to complete the setup.
12. When the configuration is done it will say Ready
13. Press Done

You have now completed the setup and created a Stereo pair sound experience.

NOTE 1:  This is only possible with two of the same speakers.  If they are not identical (Example: Citation 100 & Citation One), setting up a stereo pair will not be an option.

NOTE 2:  It is possible to make a stereo pair of a Mk1 with a Mk2. Setup as normal.
Airplay from the Mk2 will not be available.

NOTE 3: It is only possible to use Chromecast and Bluetooth in stereo, Airplay will be mono (and should be grouped in iOS Airplay menu.

 

In Power On mode, press and hold 'Volume+' together with 'Play/Pause' for more than 2 seconds. The speaker will power off and is now reset.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

NOTE: Apple IOS users are not able to find their MAC address in Google Home app due to privacy policies in the USA and European market.

We advise setting up your device on a less secure network. Log into the router and retrieve the MAC address for your device then add it to your preferred network.

Instructions below are for Android only

1. Open your Google Home app 
2. Enable Bluetooth  on your device.
3. Enable Location service  on your Android device.
   1. Remember to "Allow" Google Home to view your location while using the app (You are asked during setup of the Google Home app).
   2. In case you denied access go to Settings  Apps  Google Home  Permissions  Allow to view Location.
4. When you at selecting the Wi-Fi network from the list of available networks, before tapping on your network you need to get the MAC address.
   1. Tap  the  located top right corner.
   2. In the pop-up menu press "Show MAC address" Write down the MAC Address.

You can now add the MAC address to your local Wireless router or system if your configuration requires this before installing the device on your network.

Finding the MAC address after speaker is installed

1. Open your Google Home app .
2. Tap on  to view your home.
3. Find your room .
4. In the top right corner tap Settings icon .
5. ​Scroll down to the bottom of the screen. You will see some system information and the MAC address as well.

Finding the software version

1. Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
2. A voice will start prompting numbers which indicates the current software version.

Playing local playlist that you created via Spotify works differently for Android TV system, which the LINK BAR has built-in!

Here is how to do it:

1. Go to the Google Play Store on your TV screen (Use remote to navigate).
2. Download the Spotify app
3. Sign-in with your account.
4. You can use the dedicated app and navigate through your playlist.
5. Alternatively, you can now use voice commands such as "Ok Google, Play my Playlist Sunday Funday On Spotify"

Now you can enjoy Spotify using voice or the Remote Control.

*Some commands may not be available in all countries.

JBL TOUR ONE
Power off Tour One first and hold the ambient aware button on the left earcup for 2 seconds. You can get ANC on without Bluetooth connection, which will save your battery. Once you slide up the button on the right ear cup to power on, Bluetooth connection and music will return to normal.

 

JBL TOUR PRO+ TWS
Press and hold both right and left earbuds on Tour Pro+ TWS for 5 seconds at the same time. You can get ANC on without Bluetooth connection, which will save your battery. Once you press and hold both right and left earbuds for 5 seconds, Bluetooth connection and music will return to normal.

 

1. Press and hold the [VOL- ] and [SOURCE] buttons simultaneously.  The software version will scroll across the front display.
2. If a newer software version is available, download it from the JBL website.
3. Copy the two files to the Root directory of an empty USB thumb drive.
   • Update.zip
   • Checksum.txt
4. On the bar, press and hold the [POWER] and [SOURCE] buttons for more than 10 seconds.  This will reset the BAR 5.1 Surround.
5. Insert the USB thumb drive into the USB port on the rear panel of the bar.
6. On the bar, press and hold the [POWER] and [VOL-] buttons for more than 10 seconds to begin the software update process.
7. "UPDATING" will appear on the front display of the bar.
8. Wait for the software update to complete.  The unit will reboot and go back to standby.
9. Turn unit on.
10. Press and hold the [VOL- ] and [SOURCE] buttons simultaneously.  The new software version will scroll across the front display.

1. Touch the microphone icon on the screen to mute the Google Voice assistant microphone.
   1. NOTE: Google Assistant will not work when the microphone is muted.
2. Touch and press it again to unmute the microphone.
3. You can now give it any voice commands that you would like.

We included a Remote Control in your box (I know, that's sweet of us), and you need to pair it with your LINK BAR before it is working.

This is how you will do it

1. Press the BLUETOOTH button on the LINK BAR
2. Now hold the BLUETOOTH button down for 3-5 seconds.
3. When you see "SEARCHING FOR ACCESSORIES" on your TV screen, release the BLUETOOTH button.
4. On your REMOTE press the HOME and BACK buttons at the same time.
5. A Green LED light will flash on the REMOTE to indicate that it is in pairing mode.
6. Keep holding down the buttons until you see a message on the TV screen that says, "Pairing remote control to LINK BAR" After 10 seconds, release.
7. If done successfully on your TV screen, you will see an indicator counting down that it will "pair" with your remote.

Enjoy your entertainment with few clicks away!

BONUS TIP:  There is an Android app called Android TV that will turn your Smartphone into a Remote controller.

1. Enter pairing mode and connect to "device 1" (Phone, tablet, etc.)
2. Enter pairing mode again, and "device 1" will disconnect.
3. Connect to "device 2" and turn the headphone off.
4. Turn headphone on, and headphones will automatically connect to "device 1" and "device 2" simultaneously.
5. Pause one device and play from the other to swap the headphones connection.

NOTE: Maximum number of devices connected to the headphones at any given time is 2 source devices (Phone, tablet, etc.).

How to pair an Enchant Subwoofer with your Enchant bar

1. Go to the back of your Enchant soundbar (800 or 1300)
2. Press the "Subwoofer pairing" button for 2 seconds.

3. In front of your Enchant display, it will say "Subwoofer pairing"
4. Go to the back of your Enchant subwoofer.
5. Press the "Subwoofer pairing" button.

6. The small LED indicator will start to flash rapidly and when the connection is successful, it will be a steady light.

You now have more bass performance and can enjoy deeper richer sound!

1. Power on your Enchant 800 or Enchant 1300 Soundbar. 2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar. 2.1. Press the dedicated source button on top of your Enchant soundbar source 2.2. Press the source button until you see "Bluetooth" in the front of the Enchant display. 3. The second option is to use the Remote control included with your Enchant soundbar. 4. Press the "BT" button on your Remote control. 5. The display will show "Bluetooth pairing". 6. Go to your Bluetooth settings menu on your mobile device. 7. Enable Bluetooth and connect to your Enchant 800 or Enchant 1300 Soundbar.

If you want to add more depth and bass to your LINK BAR, we have a dedicated subwoofer (not included with the LINK BAR) that you can purchase!

Pairing the Subwoofer is very simple:
1. Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly.
2. Press the “Subwoofer Pairing” button on the SW10 subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly.
3. Press the “Subwoofer Pairing” button on LINK BAR, the LED indicator on the LINK BAR blinks rapidly
4. If successful, the pairing LED indicator on both subwoofer and LINK BAR will be a steady white LED light. If pairing fails, the sign on the subwoofer blinks slowly.
5. If the pairing fails, repeat the steps above. If you are still experiencing problems, please try to switch off all wireless devices in the home (such as routers, TV sets with wireless function, telephones, computers, etc.), then try again. It may be overcrowding on the 5GHz frequency, which often causes problems. By eliminating all other wireless activity, this will help space for the LINK BAR to establish its connection. You now should be able to pair without problems. Once pairing is complete, you can switch your devices on again

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.

You will see a notification in the recommendation option on your TV screen when there is an upgrade is available.

The system will download the firmware and apply the update after your confirmation.

You can also manually check for updates. Go to the settings menu and select “About” followed by “System Update.”

Before starting, remove any interference that might be blocking the Soundbar side-firing speakers. Any ambient noise or sounds that could disrupt the calibration needs to be out of the room. After completing the initial setup in Google Home app, select the Settings screen on the touch display of the product. Select "Speaker Setup", and then "Calibration". Follow the directions in the display to perform the calibration. A series of tone sweeps/chirps will play in all directions, and the calibration process will finish within approx. 30-40 seconds. Calibration is done! In case you are moving the soundbar you will need to calibrate the sound again.

Prerequisites:
− Make sure that your room is quiet;
− Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
− Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.

The calibration is done in two steps: Listening zone & Speaker position

Calibrate the listening zone

1. Place the detachable rear speakers beside your seating position.

2. On the remote control, press and hold HDMI until “1-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “1-DONE”: Calibration of the listening zone is completed successfully.

Calibrate the speaker position

1. Place the detachable rear speakers in your desired location.

2. On the remote control, press and hold HDMI until “2-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “2-DONE”: Calibration of the speaker position is completed successfully.
3. To select suitable surround sound level, press repeatedly to switch between high, low or middle (default).

NOTES:
− During calibration, all buttons on the remote control are disabled except for STANDBY and HDMI.
− “SETUP FAILED” is displayed if calibration failed.

This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.

USB Stick

1. Get an empty stick with speed of 2.0.
2. Make sure it is formatted with FAT16 or FAT32.
3. Your Music files can only be:  (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
4. The Partybox supports up to 8 subfolders.
5. It will be played in alphabetic sequence with main folders first then subfolders.
6. To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.

Playing music over Bluetooth connection is very simple to do:

1. Short press the dedicated Bluetooth button on the LINK BAR.
2. Go to settings on your phone.
3. Find Bluetooth and enable it.
4. Select the JBL LINK BAR in your device list.
5. You are now paired and ready to jam your favorite music!

If you are experiencing issues with the speakers turning off automatically while in use, try the following to resolve the issue (PC only):

• Enter 'Device Manger' in the Windows search bar (the magnifying glass icon at the bottom left of the taskbar in Windows 10), it should now appear in the search results under Control Panel.
• In the Device Manger list, navigate to your Universal Serial Bus Controllers, then select the 'USB Root Hub' device, right click it and select Properties.
• In the 'USB Root Hub' Properties select 'Power Management' from the options at the top, now turn off the setting 'Allow the computer to turn off this device to save power'.

The steps above may also solve issues relating to audio dropouts.

Daily Care instructions for Citation speakers fabric (wool) Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years. Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself! Many types of stain can be removed using warm water with a microfiber cloth (not too wet). Stain removal guide If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains. Here is how to do it. First, soak up the liquid with an absorbent napkin or Microfiber cloth. For dried stains use a spoon to roughen the surface. To avoid the stain spreading further start from the edge of the stain working towards the middle. WARNING! Be careful when using solvents, because these could dissolve the upholstery material beneath. Regular and normal cleaning Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth. When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric). General information These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device. In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker. HARMAN do not have any recommended companies or partners to redirect any customers too. For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below: https://kvadrat.dk/care-and-maintenance/upholsteries https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf There are a lot of information about the fabric we are using and you can contact them for further information.

Daily Care instructions for Citation speakers fabric (wool)

Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years.
Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself!

Many types of stain can be removed using warm water with a microfiber cloth (not too wet).

Stain removal guide

If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains.
Here is how to do it.

1. First, soak up the liquid with an absorbent napkin or Microfiber cloth.
2. For dried stains use a spoon to roughen the surface.
   1. To avoid the stain spreading further start from the edge of the stain working towards the middle.
3. WARNING!
   1. Be careful when using solvents, because these could dissolve the upholstery material beneath.

Regular and normal cleaning

Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth.
When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric).
 

General information

These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device.
In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker.
HARMAN do not have any recommended companies or partners to redirect any customers too.

For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below:
https://kvadrat.dk/care-and-maintenance/upholsteries
https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf

There are a lot of information about the fabric we are using and you can contact them for further information.

Please go to this Youtube address to watch an instruction video about how to record sound effects on JBL PartyBox 1000: https://www.youtube.com/watch?v=vcuIPVfnC8Q&list=PLPlXZNivfAs4mndPKnjUkB2ZggcA4cZvc&index=6&t=0s

To re-establish the functionality of the Advanced Swipe Controls (details in the image below), first update the My JBL Headphones app in the Google Play/App Store.
After the installation is completed, pair the earbuds to your phone/tablet through Bluetooth and open the app.
The earbuds will be detected and displayed in the app and you should see that a Firmware update is available.


Note: Advanced touch controls are deactivated by default, in the My JBL Headphones app go to Settings  once your earbuds are displayed, then select Gestures and enable Advanced Swipe Controls. You can now select each function and assign it to a specific gesture.

Perform a factory reset on the Citation Tower speakers by pressing and holding the reset button on the back panel for 5 seconds. After the reset you can now select "Music" to set up the Tower speakers to your WiFi network.

What You Will Need

1x Pair of Replacement Ear Cups (Part Numbers Below) 
1x Medium to Large slotted Screwdriver

Everest 300/Elite 300
SC-HM20000200-B  LEATHER CUSHION (R) BLACK 300NXT
SC-HM20000100-B LEATHER CUSHION (L) BLACK 300NXT
SC-HM20000500-B LEATHER CUSHION (R) WHITE 300NXT
SC-HM20000400-B LEATHER CUSHION (L) WHITE 300NXT

Everest 700/Elite 700
SC-HM21000200-B LEATHER CUSHION (R) BLACK 700NXT
SC-HM21000100-B LEATHER CUSHION (L) BLACK 700NXT
SC-HM21000800-B LEATHER CUSHION (R) WHITE 700NXT
SC-HM21000700-B LEATHER CUSHION (L) WHITE 700NXT

Removing the Ear Cups

1. Place the headphones on a table and while holding the ear cup with one hand gently and slowly insert the tip of the screwdriver between the ear cup and headphones.
2. Once inserted gently twist the screwdriver until there is a slight separation between the ear cup and the headphones. Note: Do not twist the screwdriver too much as this may damage the headphones.
3. Continue step 1 and 2 moving the screwdriver until there is gap between the cup and the headphones all the around the cup.

Installing the New ear Cups

1. Hold the ear cups tightly with one hand while holding the headphones with the other and gently pull until the cup is completely separated. Note that some headphones may have more adhesive than others so more pressure might be required to remove the ear cup. 
2. Find the replacement ear cup that matches the side removed (they are labeled L and R inside the cup). Align the letter in the cup so that it is legible with the bar at the top.
3. Gently press the ear cup into place ensure that the pins remain aligned.
4. Once there is a slight click sound press more firmly to set the ear cup into place.

Resetting the Partybox to Factory Settings

1. Press and hold "Play" and "Light" buttons for > 10 seconds.
2. The Partybox will power off and back on and is now reset.

Press and hold the Volume down and Voice assistant button simultaneously for more than 10 seconds. The speaker will play a sound to confirm.

Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.

In power ON mode press and hold the "Volume +" and "Phone" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. 
Now the unit is reset to factory default.
 

Press and hold the Phone and VOL + button simultaneously.
After 5 seconds, the unit powers Off, and is now reset.

Press and hold the 'Volume +' and 'Bluetooth' buttons simultaneously for > 2 seconds (> 5 seconds for the Onyx Studio 8), until the speaker powers off.
The Onyx Studio is now reset to factory settings.

In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.

Power on the JBL Pulse 3 For 5 seconds, press and hold the "Volume +" and "Play" buttons The JBL Pulse 3 will power off, and is now reset

Resetting the SOUNDSTICKS 4 to Factory Settings

1. The unit must be on
2. Press and hold Power and Bluetooth buttons for > 10 seconds
3. The unit is reset

Press and hold the 'DAB/FM' & 'Preset 1' buttons for more than 2 seconds. The Horizon 2 is now reset to the default factory settings.

Resetting the Partybox to Factory Settings

1. Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
2. The JBL Partybox will power off and back on and is now reset.

In order to reset the headphones: 

Long Press of volume + and volume - at the same time while the unit is on. Make sure that bluetooth is NOT on and connected to any device. 
When reseting, LED will blink faster. 

On the bottom of your ADAPT+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.

Resetting the device

1. In any source mode, press and hold the power button and Source button for 5 seconds.
2. When the factory settings restore is complete, the soundbar automatically turns off and restarts.
3. You can now set it up via Google Home app again or connect any new Bluetooth devices.

To reset your JBL Bar 2.0 or 2.1 back to factory default settings, follow the steps below.

1. Turn on your JBL Bar 2.0 or 2.1
2. Press SOURCE and POWER buttons on top of the bar at the same time for more than 3 seconds.
3. Your soundbar will now power off and on again.

All Bluetooth paired devices are now removed from the internal memory; please Bluetooth pair your devices again.

The factory reset button restores your device to the default settings, including network and audio configurations. 

Please use one of the following solutions:

1.  Press and hold VOL -, VOL +, and Source buttons on the device at the same time until the LED light flashes (hold for more than 5 seconds)

Or alternatively;

2. Open your JBL ONE App.
3. Navigate to the support tile.
4. Select RESTORE FACTORY SETTINGS. 

With our JBL BAR 5.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings.

Let us walk through each one of them.

Resetting WiFi settings

1. Turn on your JBL BAR 5.1 Surround.
2. Press and hold POWER button down for more than 10 seconds.
3. All of your WiFi configuration is lost and you need to reinstall it again.

Use the Google Home app to install the device on your WiFi network.

Resetting to Factory default settings

1. Turn on your JBL BAR 5.1 Surround
2. Press and hold POWER and SOURCE button for 3 seconds.
3. Your device is now reset.

You can now start allover with installing your BAR 5.1 Surround.​​​​

If you wish to reset your speaker due to various reasons, then keep reading, and follow along. 1. Press and hold Volume+ & Play/pause buttons down at the same time for more than 5 seconds. 2. The Pulse 4 will turn off, indicating that you did a successful reset. 3. Switch your Pulse 4 on again. 4. Connect with your favorite Bluetooth device and enjoy the music! Do you still have problems? Contact our Customer Service for more help!

The reset for the Tuner 2 and Tuner XL is as follows:
Reset to factory default - Long press Preset 1 & Bluetooth buttons for more than 10 seconds.

1. Power on the Enchant 800 or Enchant 1300 Soundbar. 2. In any source mode, press the power and source button for 5 seconds. 3. The Enchant 800 or Enchant 1300 will power off automatically and turn on again. 4. Your device is now reset back to default Factory settings. 5. You can now redo the setup through the Google Home app or pair with a new smartphone or tablet.

If you encounter issues using the speaker with your phone or tablet, or you want to remove all previous Bluetooth pairings from the speaker, it may be necessary to 'factory reset' the speaker.

How to reset
First, remove or forget the speaker from the list of paired Bluetooth devices in the settings of the phone or tablet.
Then, with the speaker powered on, press and hold the Volume + and Play buttons simultaneously for 3 seconds until the unit turns off.
The speaker has now been restored to factory default settings. 

Usually, the first time you connect the N90Q to your computer with the USB cable, and turn the headphone ON, it will cause a message to open on your computer, informing you that this new device has been connected, and a software package is being imported. Next time, you may get a warning that your USB device is not recognized by the computer, but that does not mean that the headphone will not work, it just means that you must activate it in the audio control systems. Locate the speaker symbol, which is usually shown at the extreme right in your computer taskbar along the bottom of the screen. Right-click on the speaker symbol. A menu opens, and you must highlight and click on Playback Devices. Now a small window opens, showing the Playback tab, with all available speaker option. One of the options should read something like this: " Speakers. AKG N90 headphones - Firmware version A2.12. Ready." Highlight this option, and then click the "Set Default" button that is now available in the window. Audio should immediately be sent to the N90 headphones as a digital signal, which is then converted and amplified inside the headphones. Now you can enjoy world-class music listening. If the computer will not show N90Q as an option, it is usually a solution to disconnect the headphone, then reconnect it. Sometimes this must be done two or three times before the computer "sees" the headphone.

What you need first

• A Harman/Kardon Enchant Soundbar (1300 or 800 model).

• Latest version of the Google Home app
• A mobile device or tablet with Android or iOS system.
• An internet connection.
• Dual-band router with 2.4GHz and 5GHz connection

Adding your Enchant soundbar to your Wi-Fi

1. Open the Google Home app

      

2. Click on "ADD" to connect your Enchant 800 or Enchant 1300 Soundbar to your Wi-Fi network.
3. Follow the instructions on screen and enjoy beautiful sound using Chromecast technology.

The Citation product with Airplay 2, use an iOS feature named Wireless Accessory Configuration (WAC), which is the easiest way to set up Wi-Fi for iPhone users. If you want to set up AirPlay with WAC and set up Google Assistant later, you can follow the below instructions.

1. Go into the Wi-Fi settings on the iPhone/iPad
2. Select the speaker you want to set up AirPlay under “SET UP NEW AIRPLAY SPEAKER...” on the lower part of the display.
3. Choose the Wi-Fi network you want to connect this speaker to, then press Next. This should normally be the same network your phone is connected to, which will appear as the default option.
4. The speaker will connect to the Wi-Fi network. Press Done to finish the setup.
5. After setup is successful. You can tap the Airplay symbol in Control Center or from your favorite audio streaming app to use AirPlay from your iPhone and iPad.

Note:

• If you don’t see the correct Wi-Fi network, make sure that the speaker is in range of the Wi-Fi router or access point.
• If your iPhone or iPad has never connected to this Wi-Fi network before, you will need to enter the Wi-Fi password at this time. Most users will not need to enter this password.
• If you cannot see your speaker under “SET UP NEW AIRPLAY SPEAKER...”, unplug and plug in power again to start it again.
• About streaming music from Apple TV, iTunes and Mac, you can visit https://support.apple.com/HT202809 for more information.

Download the Google Home app, available for iOS and Android versions. 1. Open the Google Home app. 2. Plug in power for your Enchant 800 or Enchant 1300 Soundbar. 3. Enable Bluetooth. 3.1. Enable Location service on your phone and permit Google Home app to view your location (Android only). 4. Click setup device in your Google Home app. 5. Follow the instructions provided in the app, and enjoy Chromecast streaming for your Enchant soundbar!

1. Power on your JBL LINK speaker.
2. Verify that you are connected to the right Wi-Fi network on your smartphone.
3. Open your Google Home app .
4. Enable Bluetooth
5. Enable Location Service (Android Only)
   1. Make sure you have permitted the Google Home app to view your location.
6. First option Tap Add Set up device Set up new devices in your home
7. Second  option Tap X device found Select Home location
8. Follow the instruction on screen to add your new JBL LINK speaker.

You are now all set and can enjoy your LINK device!