How To

Support Overview / How To

How To

1414 results

Sort

Page size

Why do all top panel LEDs flash when switched on? Why can the product not be connected or does not function?
The top panel LEDs are flashing because the OTA firmware update is in progress, the product should work after the upgrade is completed. It may have been caused by a previous interruption to an update.

It should be possible to resolve the issue by doing the following:
- Plug in the power cable and wait for at least 5 minutes for the Partybox Ultimate to complete the update.
- If the Partybox Ultimate stops flashing, but cannot power on, then perform a factory reset by pressing the two buttons below for more than 10 seconds: Moment (heart symbol) and Play (or through the JBL One app). After this has been done, press the Power button.
Was this helpful? Thank you for your feedback!
Re-establishing Volume Levels/Balance between Earbuds

As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds and your ears. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

Was this helpful? Thank you for your feedback!
Your Google data and privacy data

The Facts about your data and how Google uses them.

To improve their services:
Google uses the data to make their services faster, smarter, and more useful to you, such as providing better search results and timely traffic updates.
Data allows Google Assistant and their services to be more efficient and faster.
Google Assistant learns over time to provide better and more personalized feedback.
Yes, Google services are protected by one of the world’s most advanced security infrastructures. Conversations within your LINK BAR is encrypted by default.

Your Search history:
Your search history on the LINK BAR will appear in your Google account's search history. Also, if you give the LINK BAR permission, it may access your data saved in other Google services such as Calendar and Gmail to answer questions you ask.

Conversations and questions:
Any conversation or search history is stored in the cloud via your Google account and saved until you choose to delete it in the Google Home app. The LINK BAR does not keep or store any data locally.

We hope that your concern about the Privacy data is answered.

Was this helpful? Thank you for your feedback!
You can use the device without turning on TV

The LINK BAR is always ON, and you can ask the LINK BAR questions whether your TV is ON or OFF.
You can easily play music as well, there are no limits!

Was this helpful? Thank you for your feedback!
Xbox Information

All JBL Quantum headset models work only through 3.5mm audio jack (aux) connected to the Xbox controller. You cannot connect to any Xbox Series console via Bluetooth.

Please note: JBL QuantumENGINE is only available on PC.

Was this helpful? Thank you for your feedback!
Wireless network connection is lost or not connected anymore
Wireless Network connection is lost or not connected anymore

In case you have lost the Wireless Network connection, recently changed your Wireless name/password, or changed your ISP (service provider), you may need to set up your Citation device again.

Follow our steps below to try fixing the issue and reconnecting your device again.
1. Open your Google Home app .
2. In the top right corner of the home screen, tap Devices to see your available devices.
3. Scroll to find the Citation device card.
4. Tap SET UP and complete the setup steps.
5. All of your previous settings, account information is still attached to the speaker. You only need to add it again to your Wireless Network.
Note: The name of your Citation device might be a room name such as "Living Room Speaker", simply tap the SET UP.

Wireless Network connection failed
If the above solution did not work and you still have issues with connecting to your new Wireless Network, then try following these steps:
1. Reboot your Wireless router. In many cases it can help a lot with a little reboot!
2. Reset your Citation device.
  1. Press and hold down the RESET BUTTON for 15 seconds, the front LED will light up indicating it has been reset.
  2. Your Citation device will now boot-up again. It can take roughly 45 seconds until it is ready.
3. Try to set it up again via your Google Home app
Was this helpful? Thank you for your feedback!
Will tracks made available offline from Apple Music be playable on the Omni system?

Yes, through Bluetooth restreaming. Tracks made available offline in Apple Music are DRM protected and are not playable in the Harman Kardon Controller app. To play these tracks, or any other Apple Music tracks, first connect to any Omni speaker via Bluetooth and then restream to the other Omni speakers in your house with the Link button, or by grouping different rooms in the Controller app. We are looking into the possibility of adding direct support for Apple Music, so check back for updates.

Was this helpful? Thank you for your feedback!
Will the Playlist speaker support JBL Connect?

There is no plan for adding JBL Connect support for Playlist speaker. But you can group any speaker together that support Chromecast built-in for multi-room experience.

Was this helpful? Thank you for your feedback!
Will the OMNI BAR+ automatic wake up when TV is turning on?

Yes, our OMNI BAR+ supports standard CEC features such a wake-up and volume control via HDMI. Optical and analog input signals can wake up the Omni Bar, but if the source signal is too weak, the OMNI BAR+ will not wake up.

Was this helpful? Thank you for your feedback!
Will the new HK Controller app work with 1st generation Omni speakers?

Yes, they are backward compatible with your existing Omni speakers.

Was this helpful? Thank you for your feedback!
Will the head tracking function (JBL QuantumSPATIAL 360) work when connected to a PC/PlayStation/Xbox without the JBL Quantum Engine installed?

When connected to a device using the Wireless USB (A or C) dongle the head tracking feature (JBL QuantumSPATIAL 360) will work. To enable JBL Quantum 360SPHERE and spatial calibration the JBL Quantum Engine is required.

Was this helpful? Thank you for your feedback!
Will the head tracking feature work when connected via Bluetooth for the JBL Quantum 910P/X?

The head tracking will only work when connected via the wireless USB (A or C) dongle. The reason for this is that the head tracking technology uses a lot of processing power and a low latency connection.

Was this helpful? Thank you for your feedback!