How To
How To
1413 results
-
Here are all the possibilities of how you can charge devices from your power bank.
- InstantGo 5,000 with built-in Lightning cable: 1 (1 x integrated cable)
- InstantGo 5,000 with built-in USB-C cable: 2 (1 x integrated cable, and 1 x USB-C output)
- InstantGo 5,000 wireless: 3 (1 x Wireless, 1 x USB-C output and 1 x USB-A output)
- InstantGo 10,000 with built-in Lightning cable: 2 (1 x integrated cable, and 1 x USB-A output)
- InstantGo 10,000 with built-in USB-C cable: 3 (1 x integrated cable, 1 x USB-C output and 1 x USB-A output)
- InstantGo 10,000 wireless: 3 (1 x Wireless, 1 x USB-C output and 1 x USB-A output)
Was this helpful? Thank you for your feedback! -
You can easily adjust the volume to your choosing while setting your alarm on the Horizon 2. When setting your alarm, choose the Alarm Bell 1 or the Alarm Bell 2 on the top of the speaker. As you go through your settings when choosing an alarm time, it will give you the option to adjust the volume setting you wish to have on the alarm. Just simply adjust the volume by turning the volume knob on the top of the speaker. After you choose the volume, press the volume knob once to move to the next settings option.
Please note: the alarm volume will gradually increase until you choose to either snooze or turn the alarm off completely.Was this helpful? Thank you for your feedback! -
You must first set a radio preset by tuning to a radio station and holding down the 1, 2, or 3 button to save it. After this, the preset will be an option when setting up a new alarm.
When setting up the alarm, the options will be displayed in the following order:
1. Set Alarm Hour.
2. Set Alarm Minute.
3. Set Recurrence - Weekday/Once.
4. Set Ringtone - 4 built-in alarm tones or radio preset 1/2/3 (see information above).
5. Set Light - On/Off.
If the light is set to 'On' when the alarm is set up, once it goes off it will gradually increase in brightness over 10 seconds.Was this helpful? Thank you for your feedback! -
On backup battery power, please wait 50 seconds for the alarm to turn off automatically.
Was this helpful? Thank you for your feedback! -
In order to skip the tracks on the Y500 headphones, slide and hold Volume Up (to skip forward) or Volume Down (to skip backwards) for 3 seconds. These buttons are located on the LEFT ear cup.Was this helpful? Thank you for your feedback!
-
In order to power on and pair the Y500, make sure that the device you are attempting to connect to has the BT on and is in search mode. Move the ON/OFF button from its OFF position to its ON position, which is the middle of the cutout located on the RIGHT ear cup. It will remain there, and the headphones are now ON. The blue LED will start blinking, indicating that Bluetooth pairing is possible. If you need to reset the BT pairing, move the ON/OFF button against the spring load button to the opposite position of the OFF position, and keep it there for 4- 5 seconds. Now the BT system is reset, and new pairing is possible. Please Note: The Y500 features Multi-point Connectivity which allows you to switch from two different devices.Was this helpful? Thank you for your feedback!
-
The Y500 features the speed charge (5 min charging time = 1 Hour Playtime) In order to charge the headphones, use the micro USB charger that is included in the packaging. The charging port is located at the bottom of the RIGHT ear cup. Once the headphones are charging, you will see a solid red light next to the port. Once the headphones are fully charged, the red light indicator will turn off. Please Note: You cannot use the headphones via BT while they are charging. However, you can use the headphones via audio cable while charging.Was this helpful? Thank you for your feedback!
-
The Y500 headphones do not support Apt-X audio codec. However, they do support AAC audio codec.Was this helpful? Thank you for your feedback!
-
Press and hold Volume Up or Volume Down located on the LEFT ear cup for 3 seconds to skip forward or backward.Was this helpful? Thank you for your feedback!
-
Move the ON/OFF button from its OFF position to its ON position, which is the middle of the cutout. It will remain there, and the headphones are now ON. The blue LED will start blinking, indicating that Bluetooth pairing is possible. If you need to reset the BT pairing, move the ON/OFF button against the spring load, to the opposite position of the OFF position, and keep it there for about 5 seconds. Now the BT system is reset, and new pairing is possible.Was this helpful? Thank you for your feedback!
-
You can activate the Ambient Aware and TalkThru functions and assign one of them to the smart-button. AA will open the external microphones and mute the music so you can hear what is going on around you. TalkThru permits you to have a conversation with other people in the room, just by pressing the button.Was this helpful? Thank you for your feedback!
-
You cannot disengage ANC, it is always on when the headphones are on. However, you can listen to music via cable if you do not switch the N700 on at all, which means that ANC will not be active.Was this helpful? Thank you for your feedback!
-
The memory can support up to 8 paired devices, but only one device can play at a time on the N700NC headphones.Was this helpful? Thank you for your feedback!
-
When the headphones are charging-Red LED When the headphones are fully charged-The red charging indicator LED turns off When the headphones are looking for a device- Fast blinking blue LED When the headphones are connected to a device-Solid blue LEDWas this helpful? Thank you for your feedback!
-
You can use the headphones while charging but only the wired connection will work. No active functions are available since they cannot be switched on.Was this helpful? Thank you for your feedback!
-
In order to use the headphones for phone calls, press the multi-button once when the phone rings. You need to be connected to your device via bluetooth.Was this helpful? Thank you for your feedback!
-
The N700NC does not support Apt-X audio codec.Was this helpful? Thank you for your feedback!
-
You can create several different EQ settings that are stored in the memory within the new AKG Headphones app.Was this helpful? Thank you for your feedback!
-
AirPlay uses a differnet network card inside the BDS. If it doesn't receive any IP adresses, it won't work. To check and see if your network card in BDS did receive an IP address, you can use an app called Net Analyzer for iOS and WiFi Analyzer for Android. Simply scan your network with one of them, and you should be able to see your BDS IP address, usually the IP after your main IP for BDS, should be AirPlay network details. If you have trouble, please contact our helpdesk for further assistance.Was this helpful? Thank you for your feedback!
-
This is because most Windows do not support A2DP stereo audio streaming via Bluetooth, the standard for music-listening through Bluetooth. The system will support keyboards, mice, printers etc. via Bluetooth, but not audio. It is necessary to download the proper drivers, either from the computer manufacturer, the software manufacturer or the manufacturer of the Bluetooth chip in the computer. Help to do this must be sought with the companies that supply one or more of these computer features.Was this helpful? Thank you for your feedback!
-
In order for the No. 526/No. 523 to return to the last input that had been selected you must put the unit in standby before turning power OFF.Was this helpful? Thank you for your feedback!
-
The Bluetooth connection will not keep playing once you have switched the source. Simply press play again on your Bluetooth device to start streaming once again.Was this helpful? Thank you for your feedback!
-
No, unless you have set up devices with both voice assistants, you cannot use Alexa to control devices you set up only in the Google Home app, or use Google Assistant to control devices you set up only in the Alexa app.
Was this helpful? Thank you for your feedback! -
Yes, you can use the universal command “ Stop”, “Dismiss”, “Cancel” and “Quiet” to stop the current music playback, alarm and timer.
Was this helpful? Thank you for your feedback! -
No. Alexa notifications must be set up in the Alexa app and you can control the notification via Alexa voice only.
Was this helpful? Thank you for your feedback! -
This happens if you power up the subwoofer before connecting the right and left speakers. The system mutes to avoid potentially harmful pop noise. Just touch one of the volume up/down pads to unmute.Was this helpful? Thank you for your feedback!
-
High pass filter
When the subwoofer is connected, the main channels are "Small", meaning that there is a high-pass filter. This ensures proper blending with the subwoofer.
Crossover settingsThe Citation amp supports crossover settings in the range 50Hz - 120Hz. Default is 80Hz.
Multiple subwoofers?Only one type of subwoofer is supported at a time. Either with cable or wireless.
Was this helpful? Thank you for your feedback! -
If you have already setup your JBL BAR 5.1 SURROUND with Google Home or AirPlay, you can now sign into your Amazon account via the JBL BAR Setup App. Just download the app and follow the instructions.Was this helpful? Thank you for your feedback!
-
There are several ways to access the advanced settings. In the settings page, you can adjust settings for subwoofer, EQ and input sensitivity.
Make sure your PC or smartphone is connected to the same network as Citation AMP:
1. On a PC, go to the "Network" folder". There you can find an icon for the Citation Amp. Double click that, and you are taken to the internal webpage for advanced settings for your Citation Amp.
2. Or, in the Google Home app, go to settings for the Citation Amp. At the bottom of the page, you can find the device IP address. Copy and paste this address into your web browser, and you are taken to the internal webpage for advanced settings for your Citation Amp.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)