Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.

Daily Care instructions for Citation speakers fabric (wool) Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years. Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself! Many types of stain can be removed using warm water with a microfiber cloth (not too wet). Stain removal guide If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains. Here is how to do it. First, soak up the liquid with an absorbent napkin or Microfiber cloth. For dried stains use a spoon to roughen the surface. To avoid the stain spreading further start from the edge of the stain working towards the middle. WARNING! Be careful when using solvents, because these could dissolve the upholstery material beneath. Regular and normal cleaning Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth. When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric). General information These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device. In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker. HARMAN do not have any recommended companies or partners to redirect any customers too. For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below: https://kvadrat.dk/care-and-maintenance/upholsteries https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf There are a lot of information about the fabric we are using and you can contact them for further information.

Daily Care instructions for Citation speakers fabric (wool)

Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years.
Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself!

Many types of stain can be removed using warm water with a microfiber cloth (not too wet).

Stain removal guide

If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains.
Here is how to do it.

1. First, soak up the liquid with an absorbent napkin or Microfiber cloth.
2. For dried stains use a spoon to roughen the surface.
   1. To avoid the stain spreading further start from the edge of the stain working towards the middle.
3. WARNING!
   1. Be careful when using solvents, because these could dissolve the upholstery material beneath.

Regular and normal cleaning

Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth.
When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric).
 

General information

These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device.
In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker.
HARMAN do not have any recommended companies or partners to redirect any customers too.

For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below:
https://kvadrat.dk/care-and-maintenance/upholsteries
https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf

There are a lot of information about the fabric we are using and you can contact them for further information.

USB Stick

1. Get an empty stick with speed of 2.0.
2. Make sure it is formatted with FAT16 or FAT32.
3. Your Music files can only be:  (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
4. The Partybox supports up to 8 subfolders.
5. It will be played in alphabetic sequence with main folders first then subfolders.
6. To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.

This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.

1. Power on your Enchant 800 or Enchant 1300 Soundbar. 2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar. 2.1. Press the dedicated source button on top of your Enchant soundbar source 2.2. Press the source button until you see "Bluetooth" in the front of the Enchant display. 3. The second option is to use the Remote control included with your Enchant soundbar. 4. Press the "BT" button on your Remote control. 5. The display will show "Bluetooth pairing". 6. Go to your Bluetooth settings menu on your mobile device. 7. Enable Bluetooth and connect to your Enchant 800 or Enchant 1300 Soundbar.

How to pair an Enchant Subwoofer with your Enchant bar

1. Go to the back of your Enchant soundbar (800 or 1300)
2. Press the "Subwoofer pairing" button for 2 seconds.

3. In front of your Enchant display, it will say "Subwoofer pairing"
4. Go to the back of your Enchant subwoofer.
5. Press the "Subwoofer pairing" button.

6. The small LED indicator will start to flash rapidly and when the connection is successful, it will be a steady light.

You now have more bass performance and can enjoy deeper richer sound!

1. Touch the microphone icon on the screen to mute the Google Voice assistant microphone.
   1. NOTE: Google Assistant will not work when the microphone is muted.
2. Touch and press it again to unmute the microphone.
3. You can now give it any voice commands that you would like.

Finding the software version

1. Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
2. A voice will start prompting numbers which indicates the current software version.

NOTE: Apple IOS users are not able to find their MAC address in Google Home app due to privacy policies in the USA and European market.

We advise setting up your device on a less secure network. Log into the router and retrieve the MAC address for your device then add it to your preferred network.

Instructions below are for Android only

1. Open your Google Home app 
2. Enable Bluetooth  on your device.
3. Enable Location service  on your Android device.
   1. Remember to "Allow" Google Home to view your location while using the app (You are asked during setup of the Google Home app).
   2. In case you denied access go to Settings  Apps  Google Home  Permissions  Allow to view Location.
4. When you at selecting the Wi-Fi network from the list of available networks, before tapping on your network you need to get the MAC address.
   1. Tap  the  located top right corner.
   2. In the pop-up menu press "Show MAC address" Write down the MAC Address.

You can now add the MAC address to your local Wireless router or system if your configuration requires this before installing the device on your network.

Finding the MAC address after speaker is installed

1. Open your Google Home app .
2. Tap on  to view your home.
3. Find your room .
4. In the top right corner tap Settings icon .
5. ​Scroll down to the bottom of the screen. You will see some system information and the MAC address as well.

In Power On mode, press and hold 'Volume+' together with 'Play/Pause' for more than 2 seconds. The speaker will power off and is now reset.