How To

Support Overview / How To

How To

435 results
  • How do I program preset FM stations in my JBL Horizon?
    The owner's manual can be a bit difficult to understand. Here is what to do to program a preset station that has not already been saved in any preset: 1 Turn on the radio by clicking the FM button. 2 Find the station you want to save by doing what is shown under pt. 8 B or C, either clicking or pressing/holding for more than 2 seconds the left/right arrow buttons. 3 Press and hold the FM button for more than 2 seconds. Now the preset number appears blinking. 4 Click on the left/right arrow buttons to skip through the preset positions. 5 When you have located the desired memory preset position, such as Preset 4, confirm by clicking the FM button. Now the desired FM station is saved in memory preset 4. If you have already saved an FM station in a preset memory position, and want to have a new station placed there instead, here is what to do: 1 Turn on the radio by clicking the FM button. 2 Jump to the preset station you want to change with the round central button. Each click advances to the next preset. 3 When you are on the preset you want to change, e.g. preset 4, press and hold the FM button for more than 2 seconds. 4 The FM symbol and the frequency will now blink. 5 Before they stop blinking, click, or press and hold one of the arrow buttons to go through the FM frequencies step by step, or perform station search. 6 When you have found the new station you want to save in preset 4, click the round central button. 7 Now the new station is saved in preset 4.
  • How do I power on and pair with the Flip 3 SE?
    Press the power button on the Flip 3 SE once to power on the device. When you power on the Flip 3 SE for the first time, it will automatically go into Bluetooth Pairing mode and you should be able to find the Flip 3 SE in the list of available Bluetooth devices on your mobile phone/tablet. Press the Bluetooth button on the Flip 3 SE to enable pairing mode manually
  • How do I power on and pair the GO 2?
    Press the power button located on the far Left top of the speaker. If this is your first time pairing the device, the speaker will automatically go into pairing mode. Make sure that the product you are attempting to pair to is in search mode and in bluetooth range. The Go 2 should pop up on discoverable devices. Choose the Go 2 option and you will be connected within a few seconds.
  • How do I power on and pair the Everest 750NC headphones?
    Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.
  • How do I pair the subwoofer to my JBL BAR soundbar if pairing does not happen automatically?
    Normal pairing is automatic, and happens when you first switch both devices on. If pairing does not take place automatically, or you have to force new pairing, here is what to do: Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly. Second, press the CONNECT button on the subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly. Third, press and hold the DIM DISPLAY button on the remote control for 5 seconds, followed by short press on BASS+, and BASS- button in sequence. Panel display will show “PAIRING”. If pairing succeeds, the LED indicator on the subwoofer lights up, and the soundbar display will show "DONE”. If pairing fails, the indicator on the subwoofer blinks slowly. Lastly, if the pairing fails, repeat the steps above. If you have continued trouble performing the pairing, please try to switch off all wireless devices in the home, then try again. This means routers, TV sets with wireless functions, telephones, computers etc. Since overcrowding on the 2.4 GHz frequency now often causes problems, eliminating all this activity makes space for the Bar to establish its connection, and you should be able to pair without problems. Afterwards, you can switch your devices on again. Often, all will now work fine, and if not, you will know which devices are doing the interference.
  • How do I pair the Flip 3 SE with a different device?
    Power on the Flip 3 SE and press the Bluetooth button. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tablet.
  • How do I lock my JBL Endurance DIVE before going into the water?
    Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.
  • How do I know when the battery in the Flip 3 SE needs charging?
    The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.
  • How do I know that JBL QuantumSURROUND Sound is turned on from my headsets?
    You can check on the JBL QuantumENGINE Spatial Sound page or check whether the Spatial Sound slider on top is on
  • How do I know if the headphones are fully charged on the UA Train headphones?
    As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.
  • How do I know if my software requires an update?
    You will get a notification or if you go to the System section, and the firmware button is highlighted with "Download Firmware", you can download and install the firmware.
  • How do I know if my headset requires a firmware update?
    You will get a notification or if you go to the System section, and the software button is highlighted with "Download Firmware", you can download and install the firmware.
  • How do I know if a game has surround sound output?
    This changes from game to game, but most games have an “Audio Settings” section where you can adjust your game’s audio settings. Check the game’s official website for more information.
  • How do I get the best surround experience with each game?
    Every game has different audio output options and different ways the audio was designed. Some games make better use of multi-channel setups than others. We recommend you experiment with settings in the JBL QuantumENGINE to find the best match for your unique gaming style.
  • How do I get Hi-Res audio on my JBL Tour One M3?

    The built-in Digital-to-Analog Converter (DAC) makes it possible to enjoy lossless high sound quality with low distortion and accurate conversion.

    Connect the headphones with the included USB-C cable or 3.5mm aux cable to any audio source to enable Hi-Res audio. If you want to have Hi-Res audio wirelessly you need to connect an Android device with at least Android OS 13 or higher and use streaming sources such as Apple Music, Tidal or Amazon Music.

  • How do I fix occasional audio dropouts when playing music to my Omni+ and Omni?
    We recommend starting playback on the Omni+ speaker first, and then linking the 1st generation Omni speakers. Omni+ is more powerful and can provide more stability when restreaming to other speakers.
  • How do I fix AirPlay not streaming music to my soundbar?
    If you cannot stream music  with AirPlay, use the JBL One App; 
    (1) Go to Settings.
    (2) Select 3rd Party Service.
    (3) Select the Airplay tile.
    (4) Select Reset AirPlay.
  • How do I connect the JBL Stadium GTO 20M midrange dome in my car system?
    The Stadium GTO 20M is intended for use with the Stadium GTO two-way systems, or to replace existing midrange speakers in systems that are already three-way from the start. The Stadium GTO two-way component systems are 3-way upgradeable. The crossovers are gap-switchable to accommodate a midrange upgrade. The optional Stadium GTO 20M midrange includes a bandpass crossover to convert a two-way system into a threeway system with perfect tonal balance. You simply connect both crossovers to the speaker wires from your car amplifier in parallel, and set the existing GTO two-way crossover to GAP function. Stadium GTO 20M is designed to also fit into many factory three-way applications. Please note that you cannot use this add-on midrange with coaxial car speakers, unless you can access the crossover networks to establish the midrange gap that the extra midrange is meant to occupy.
  • How do I connect the inputs and outputs of the Club 5501 car amplifier?
    The Club 5501 is a mono amplifier for subwoofer use in cars. It can be confusing to see that it has two inputs, marked left and right, as well as two speaker output pairs. But it is still a mono amplifier, with only one channel. The two inputs are there to make it easier to connect to a normal car radio/head unit, where you will often have two normal full-range connectors, left and right. You can insert both into the 5501. However, if you only have one signal lead going to the 5501, you can use either of the inputs. They are combined into one inside the amplifier anyway. Also, the two sets of speaker connections are there to make it easier to connect two subwoofers simultaneously. The two sets are completely identical, so you can use either one for a single subwoofer, or both. If you connect two, they will be in parallel.
  • How do I connect my Harman Kardon Allure to my Wi-Fi?
    You need to download the HK Alexa setup app from either Google Play Store or Apple App Store, then follow the procedure written in the app.
  • How do I connect JBL DRG to my smartphone and head unit both via Bluetooth?
    • Plug the JBL DRG into OBD II port in your vehicle first. • Start your engine (JBL DRG will enter low power mode when the engine is off) • Then press Bluetooth button on DRG for pairing and connection to your smartphone. • After connected, launch the “JBL DRG” app on your smartphone. • Press the settings button on the left top of the app to enter the settings page. If your head unit’s Bluetooth is in discoverable mode, please enable the “Inquiry Mode” on the settings page. If your head unit’s Bluetooth is in inquiry mode, please disable “Inquiry Mode” on the settings page. • Exit the settings page and select “Bluetooth” in “Connection Mode”, JBL DRG will start the connection with head unit.
  • How do I connect JBL DRG to my head unit via FM?
    • Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.
  • How do I activate the SIRI® and Google Now™ voice assistant integration on my JBL Boombox?
    1) Download and run the latest JBL Connect app on your phone 2) The JBL Connect app will begin discovering your JBL Boombox (please make sure your speaker is connected via Bluetooth first) 3) Use the toggle switch in the JBL Connect App to change the phone button to now have the voice assistant function 4) Simply press the “Play” button on your JBL Boombox (you will hear a brief tone) and begin speaking your commands via SIRI and Google Now. 5) Please check the below links for more information regarding SIRI and Google Now available voice commands: SIRI: https://support.apple.com/HT204389 Google Now: https://support.google.com/websearch/answer/2940021
  • How does ShareMe work?
    For models E40BT and E50BT Connect the first headphone by BT to your mobile device Tap the ShareMe button once Tap the ShareMe button on the 2nd headphones twice ( ! ) The headphones will connect to each other. When changing volume on source device, or BT connected headphones, the volume will only change on THAT headphone ( and in some cases the source device, like iOS devices and newer Android ), not on the one connected via ShareMe. When changing volume on a via-ShareMe-connected headphone ( 2nd ), it will not change volume on source device, or on the BT-connected headphone. To sum up, both headphones have their individual volumes. For Everest models ( not ELITE ). Connect the headphones by BT to your mobile device Put the 2nd device ( speaker, headphones as long as they have Bluetooth ) in "BT discovery mode" Press the ShareMe button on the Everest headphone ( button marked with a little "s" ) The Everest will connect to BT device. (Please note that you may not be able to pair from the Everest to the Everest Elite models, or if you can pair, you may have dropouts in sound). When changing volume on source device, or Everest, the volume will only change on the Everest ( and in some cases the source device, like iOS devices and newer Android ), not on the device connected via ShareMe. When changing volume on via-ShareMe-connected BT device ( 2nd ), it will not change volume on source device or Everest. Please note that it is NOT possible to use ShareMe if you are listening to analog signal via cable. Bot the E-series and the Everest models will switch off the Bluetooth circuits as soon as you insert the audio cable, so re-transmission is not possible.
  • How does JBL QuantumSURROUND virtualization technology process my sound?
    JBL QuantumSURROUND takes up to 8 channels of audio, and recreates a multi-channel setup—including overhead channels—as measured inside one of JBL’s listening rooms. You’ll hear the multi-channel mix as if you’re right in the middle of the game.
  • How does Harman Volume work on JBL Cinema Base?
    Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or off
  • How deep and for how long can I dive with my JBL Endurance DIVE?
    With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.
  • How can the K 915 wireless headset be paired to another transmitter, for instance if the original transmitter becomes defective?
    Here is the pairing procedure between a K915 headset and a new transmitter box: 1. Power off the headphone. 2. Power off the transmitter. 3. Press and hold the power button on the headphone until the “Signal” LED is flashing, and a beep sound can be heard. 4. Power on the transmitter. 5. After a short while the “Signal” LED will light constantly (stop flashing) and the pairing is complete.
  • How can I work with RGB lighting properly with JBL QuantumENGINE?
    Any changes you make on the Lighting page will be immediately reflected on your headset.
  • How can I upgrade my Harman Kardon Allure speaker?
    The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.
  • How can I switch between Active Noise Cancellation, Smart Ambient (TalkThru) and off?
    Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SHORT press the multi-function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.  
  • How can I see that charging is complete on my Y50BT?
    The red diode that lights up when charging begins will go out again when charging is complete.
  • How can I reset the JBL Bar 2.1, JBL Bar 3.1 and JBL Bar 5.1?
    Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.
  • How can I reset my OMNI BAR+?
    On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.
  • How can I reset my OMNI 50+ speaker. The reset button does not work?
    The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.
  • How can I reset my Omni+ speaker(s)?
    There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.
  • How can I reset my JBL Tuner to factory default settings?
    To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.
  • How can I reset my JBL headphones?
    With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.
  • How can I reset my JBL E25BT?
    You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.
  • How can I reconfigure the Wi-Fi for my Harman Kardon Allure speaker?
    Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.
  • How can I mute the music playing without touching the Harman Kardon Allure speaker?
    That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".
  • How can I get the JBL AmpUp App?
    Unfortunately, the JBL AmpUp App is no longer available for download.
  • How can I delete my voice interactions with Harman Kardon Allure?
    You can delete specific voice recordings associated with your account by going to History in Settings in the Alexa App, drilling down for a specific entry, and then tapping the delete button. Or, you can delete all voice recordings associated with your account for your Harman Kardon Allure speaker, by selecting the applicable product at the Manage Your Content and Devices page at www.amazon.com/mycd. and deleting voice recordings. However, this may degrade your Alexa experience.
  • HDMI features that are supported

    HDMI Output

    Both Enchant 800 and Enchant 1300 support these:
    • HDMI 2.0b compliance
    • HDCP 2.2 compliance (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
    • CEC features (Scroll to see support)

    HDMI Input

    Enchant features only 1 x HDMI input, and Enchant has 3 x HDMI inputs and support this:
    • HDMI 2.0b.
    • HDCP 2.2 for all HDMI input connections (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
    • 4K Pass-through.

    CEC Support

    CEC support only available through your HDMI connection and we are always using standard protocol for our products.
    We support these:
    • System Standby: When you press the "Power off" button on your TV remote, the Enchant soundbar will go into Standby mode as well.
    • ARC or called Audio Return Channel: If you would have a TV BOX connected directly to your TV and using ARC from TV to Enchant soundbar, then all sound will be transferred through ARC connection.
      • In case you are not using the HDMI ARC connection then sound coming from the TV show will not be transferred to the Enchant soundbar.
    • System Audio Control: Using your TV remote to turn up or lower the volume will be synchronized with the Enchant soundbar.
    Both models
    Bigger model is the Enchant 1300 and smaller model is the Enchant 800.
  • Google Assistant Not Making/Taking Phone Calls

    As of December 1, 2022, Google Assistant on third party smart displays, soundbars, and speakers are no longer able to make a voice call to a landline or mobile number on the carrier network. Voice-over-IP calls continue to work. This is due to the ongoing infrastructure improvements.

     

    Please click here to see Google’s official statement/article explaining this.

  • Game-Chat Balance Support
    For JBL Quantum 100/200/300 models, they do not offer Game-Chat audio dial function.
    To get the Game-Chat dial feature, you need JBL Quantum 400, and up, then you can adjust game-chat balance by rotating the dial-up and down.

    For models that support Game-Chat dial, when you rotate the dial, you will feel a notch that indicates 50% game and 50% chat. Or you can see the status on the top bar of the JBL QuantumENGINE.
  • For how long does the alarm sound, if it is not interrupted?
    Horizon's alarm sounds for 3 minutes, then it shuts off, or rather it goes into snooze, for 9 minutes. Then it sounds the alarm again for 3 minutes, followed by snooze for another 9 minutes. After this final snooze period, it starts playing, and keeps on playing until it is manually shut off. The light shuts off with the audio.
  • Fit and Sizing
    Try all Flex Fit Ear fins included (S/M/L) to find a snug fit for stability during workout. Usually the biggest size that fits comfortably in your ear will provide the most stability. Try all ear tip sizes (S/M/L) to find a snug seal for optimum sound quality, and look for a balance of comfort and acoustic sealing.
  • Firmware Information - JBL Firmware Update App

    If you are experiencing issues with your headphones' Bluetooth disconnecting and reconnecting while on standby, there is a new Firmware Update app to resolve this issue. Start by downloading the app  "JBL Firmware Update" (see links below).
    Google Play Store:     https://play.google.com/store/apps/details?id=com.jbl.tune.update
    App Store: https://apps.apple.com/gb/app/jbl-firmware-update/id1548227663

    Once downloaded, you can update your headphones firmware from there. 
    Below you can see step by step images of the update process.

    Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg 

  • Endurance Series Headphones: Switching Devices
    To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.
  • Endurance Series Headphones: Charging
    Fully charge the earbuds along with the charging case before the first use. The charging case is for charging the earbuds only. LED behaviors: 1 LED- 25% 2 LED-25%-50% 3 LED-50%-75% 4 LED-75%-99% NO LED-100% Fully Charged You can keep the earbuds in standby mode for up to 3 hours without having to return them to the case. beyond this point the earbuds must be returned to the case for charging. You should receive up to 4 hours of playback with additional 24 hours of backup power from the charging case.
  • Endurance Series Headphones: Apt X
    The Endurance headphones do not support Apt X or AAC audio codecs.
  • Endurance Dive Headphones: MP3 Information. How to add music, play function.
    Here is how to add music to the Dive Headphones: 1. Place the MP3 music files that you want to transfer to the Dive headphones on your computer, where you can find them again. The sequence is not important, they will be played in alphanumerical sequence. If you want to have a special sequence to your tracks, you can add a number as the first file name. 2. Connect the Dive to your computer with the USB cable. Please use the cable that came with the headphones, since other USB cables may be wired for charging only, and may not work. 3. Your Dive will now pop up in your explorer folder overview as a new drive. Total capacity is about 991 MB. 4. Now you simply drag-and-drop the MP3 files from their location onto the Dive, or you mark the files, copy them and paste them onto the Dive. Do not use folders of any kind, and do not try to place other file types on the Dive's memory. MP3 files with a resolution of 320 kbits/second is maximum quality possible. Please note that the owner's manual contains an error about random play, stating that MP3 play will always be done in random sequence. Unfortunately, this is an error. All replay of MP3 files from the internal memory is alphanumerical, NOT random. As mentioned above, you can add a number to the track title, and the tracks will be played in numerical order, until no more numbers are present, after which replay is in alphabetical order.
  • Enabling or disabling Demo mode.

    Demo mode

    1. Press the Play and Boost button at the same time for 5 seconds.
    2. Depending on what state your JBL Partybox is in, either you enter Demo mode or disabling it.
      1. NOTE: In Demo mode, you cannot use the JBL Partybox as most features and buttons are not working.
    Demo mode
  • Do you have a list of all games with surround sound?
    Check out a list of games with surround sound: https://satsun.org/audio/
  • Do you have a guide that explains the best placement for the OMNI+ speakers in a house?
    Every home is different, so it is difficult to provide a universal guide that suits it all. What you can do is check the number of available access points in your home by performing a Wi-Fi network scan using a mobile device. Then select the Wi-Fi channel that isn't as busy as the rest. Also, check how much noise each speaker has using the Harman Kardon Controller app. Simply go into the settings menu and select "Send us feedback" to see the results, signals between -40 dB and -62 dB are considered good.
  • Do the UA Train headphones support AptX low latency?
    No. UA Train does not support AptX™ and AptX HD™ audio codecs.
  • Do JBL Club Headphones Support aptX?
    JBL Club headphones do not support aptX. There are a number of different platforms available and our choice was driven by the one that provides the combination of best sound quality and user experience. The platform that we have selected perfectly fits the requirements of the JBL Club series including voice integration and audio customization whilst supplying the Hi Res-certified headphones with the quality of audio they deserve.
  • Do I need to calibrate the head tracker sensor?
    The head tracker in the Quantum ONE uses your movements to calibrate the sensors. You can speed up the calibration process by doing the following: * Imagine that the headphone is a standard cube with 6 faces (Front, Back, Left, Right, Top, Bottom) * Orient the headphone so that it is sitting on each face of "the cube" sequentially. For example, start with the headphone positioned normally (bottom face of the cube down). Then rotate it so that the right side of the cube is facing down. Then continue through the rest of the faces of the cube. * Hold the headphone in each position for 1 second * Once all the faces of the device have been rotated, set the headphone down on a stationary surface for 2 or 3 seconds.
  • Does this headphone support JBL QuantumSURROUND?

    The JBL Quantum 200 is not equipped with JBL QuantumSURROUND. You can consider to purchase the Quantum 300, which comes with a USB dongle and access to JBL QuantumENGINE. 

< 1 ... 3 4 5 6 7 8 >

Can’t find what you’re looking for?

Call us

Call us

To speak to our customer service specialist

1800-102-0525

Mon to Sun 10 AM to 7 PM IST

message

Message Us

Chat with a support agent via Whatsapp at:
91 70658 44446

Mon - Sun: 10:00 am - 7:00 pm (IST)