How To
How To
435 results
-
JBL QuantumSURROUND takes up to 8 channels of audio, and recreates a multi-channel setup—including overhead channels—as measured inside one of JBL’s listening rooms. You’ll hear the multi-channel mix as if you’re right in the middle of the game.Was this helpful? Thank you for your feedback!
-
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
Here is the pairing procedure between a K915 headset and a new transmitter box: 1. Power off the headphone. 2. Power off the transmitter. 3. Press and hold the power button on the headphone until the “Signal” LED is flashing, and a beep sound can be heard. 4. Power on the transmitter. 5. After a short while the “Signal” LED will light constantly (stop flashing) and the pairing is complete.Was this helpful? Thank you for your feedback!
-
Any changes you make on the Lighting page will be immediately reflected on your headset.Was this helpful? Thank you for your feedback!
-
The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SHORT press the multi-function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
The red diode that lights up when charging begins will go out again when charging is complete.Was this helpful? Thank you for your feedback!
-
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.Was this helpful? Thank you for your feedback!
-
The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)