How To
How To
1413 results
-
The SB20 supports these programmable IR codes for your TV remote: Volume+, Volume-, Mute and Power commands.Was this helpful? Thank you for your feedback!
-
Yes, you can control the No. 585 over port 7701, providing the control is set for Ethernet in the menu. The commands are the same as RS232 and you connect to it by telnet on port 7701 of the IP Address of the unit. Note there is no echo of the command when you type and it answers with a copy of the command and OK if it accepted the command and EH? if it did not.Was this helpful? Thank you for your feedback!
-
The JBL Bar 500 does not support rear/surround speakers. Alternatively the JBL Bar 800/1000 has detachable wireless rear speakers included.Was this helpful? Thank you for your feedback!
-
No, it only supports one Bluetooth connection. Simply disconnect the paired phone/tablet from your Bluetooth device settings, then hold down the Bluetooth button for 3 seconds, and then you are able to pair with the new smartphone/tablet.Was this helpful? Thank you for your feedback!
-
The JBL Bar 300 does not support a subwoofer. Alternatively the JBL Bar 500 has a wireless subwoofer included.Was this helpful? Thank you for your feedback!
-
It is not possible to clean the clear dome of the AURA. The dome cannot be removed without damaging the product. The only solution if debris falls into the AURA is to try to shake it out through the bass tube. We cannot recommend using a vacuum cleaner to suck or blow through the bass tube.Was this helpful? Thank you for your feedback!
-
Yes, on your computer, enter the IP address of the receiver in the internet browser. In the page that opens, it is possible to change the name.Was this helpful? Thank you for your feedback!
-
Yes, in the Harman Kardon Remote APP, it is possible to change the AURA's Bluetooth name.Was this helpful? Thank you for your feedback!
-
The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.Was this helpful? Thank you for your feedback!
-
Is Bluetooth APT X streaming supported by the JBL Bar Studio, Bar 2.1, Bar 3.1, Bar 5.1 and Bar 9.1?The speaker uses Bluetooth version 4.2 but does NOT support APT X.Was this helpful? Thank you for your feedback!
-
Yes, but only with power on the Adapt. When it senses a signal on the analog aux input, the input ring will light up green automatically, and the signal will become available from the line output, for transmission with cable to e.g. an amplifier. It is important to note that there will be a slight delay in the signal that comes out of the line output jack, even if it does not involve any wireless functions.Was this helpful? Thank you for your feedback!
-
With different storage conditions and shipping durations, your power bank may go into deep sleep mode to protect the battery. If the power bank does not start charging your device when used for the first time, connect the power bank to a power source and charge it for 15-30 minutes, it should then work normally. If it still does not work, contact our customer service team and we will be happy to help you: https://support.infinitylab.com/#contactWas this helpful? Thank you for your feedback!
-
We use a sophisticated vetting process to ensure that your image does not contain copyrighted, protected, sexual, suggestive, offensive or inappropriate elements. This includes words and messages. If these algorithms are triggered, your order is automatically cancelled. Please try again with a different image or wording.Was this helpful? Thank you for your feedback!
-
This product is rated IP67, which is different from IPX7. IP67 protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes. It is also resistant against dust. Dust accumulation around electronics can lead to hardware failure, so the IP67 rating is an extremely beneficial addition to this product.Was this helpful? Thank you for your feedback!
-
Was this helpful? Thank you for your feedback!
-
The HKTS 65 is a new version of the HKTS 60, with minor improvements. Please select HKTS 60 in the menu.Was this helpful? Thank you for your feedback!
-
The amplifier has a signal sensor on the high-level (speaker level) inputs, so it is not necessary to use a trigger cable when input is high-level, and connected to the high-level inputs. However, low-level input signals through the RCA-phone input sockets do not activate a signal sensor, so use of a trigger cable is MANDATORY for low-level input signal use.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire/Focus 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
There can be differences in the internal hardware that also implies different firmwares. These products feature the same specifications and performance expectations. If the app does not inform you of any new updates, the firmware is current and the product is performing as designed.Was this helpful? Thank you for your feedback!
-
The InfinityLab power bank will not damage your device.
The InfinityLab power bank will deliver the power your device needs during charging, andd the InfinityLab power bank features auto protection against overheating and features overcurrent/overvoltage conditions.Was this helpful? Thank you for your feedback! -
All InfinityLab power banks are < 100Wh, so there are no restrictions for taking them onto flights as hand luggage (also known as cabin baggage or carry-on luggage).
However, power banks are not allowed to be carried in your hold luggage (also known as checked luggage).Was this helpful? Thank you for your feedback! -
The new Boombox 2 does not feature the Indoor/Outdoor Mode. With the first generation Boombox, the Outdoor Mode was loud, but lacking sufficient bass. The Boombox 2 has both improved bass and loudness to create the perfect balanced sound for all environments.
Was this helpful? Thank you for your feedback! -
When using an Android device, you need to have location service active on your phone or tablet and make sure that you allowed "Google Home app" to use the phone or tablet location service. However, make sure your Wi-Fi router has UPnP enabled and that you do not use any network extenders while connecting the product.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)