How To
How To
1419 results
-
During the design phase, it was decided to optimize BT reception, which is achieved by buffering digital signal streams. Since this takes a little bit of time, a slight delay will be the result. We have now optimized the software, so the lip-sync problem is no longer an issue. Video materials can now be watched with proper audio timing. Please check the product support page "downloads" tab for your headphone to check for the update files. If you experience delay, even after performing the update, please be aware that delays can occur for several reasons. For instance, the Bluetooth transmitter in a TV set can introduce delay. Also, some TV sets can cause timing changes if certain image processes are used. Try to disengage image processing, and check if lip-sync adjustment is available in your TV. With YouTube or other streaming services: In cases of lip-sync issues, it may also be a good idea to carry out a refresh of the source website. Always try more than one streaming source to determine if the delay comes from the streaming service or from you connection.Was this helpful? Thank you for your feedback!
-
This is because a 4K TV will force the BDS into 4K resolution (upsampling), because this gives the best picture quality, being the highest resolution possible. However, there is no such thing as a 3D 4K movie. All 3D discs are full HD (1080p), but cannot be reproduced in 4K, because 4K resolution cannot be combined with 3D. The solution is to enter the setup menu of the BDS, selecting normal full HD resolution in the picture settings menu. Now 3D movies will be shown correctly on the 4K TV.Was this helpful? Thank you for your feedback!
-
This is because a 4K TV will force the BDS into 4K resolution (upsampling), because this gives the best picture quality, being the highest resolution possible. However, there is no such thing as a 3D 4K movie. All 3D discs are full HD (1080p), but cannot be reproduced in 4K, because 4K resolution cannot be combined with 3D. The solution is to enter the setup menu of the BDS, selecting normal full HD resolution in the picture settings menu. Now 3D movies will be shown correctly on the 4K TV.Was this helpful? Thank you for your feedback!
-
No, sorry it is not possible to do so, as it requires some additional hardware changes, which the old BDS systems do not have.Was this helpful? Thank you for your feedback!
-
Our BDS device do not support 5 GHz networks. You must connect it to a 2.4 GHz network (b, g or N networks).Was this helpful? Thank you for your feedback!
-
Usually, the first time you connect the N90Q to your computer with the USB cable, and turn the headphone ON, it will cause a message to open on your computer, informing you that this new device has been connected, and a software package is being imported.
Next time, you may get a warning that your USB device is not recognized by the computer, but that does not mean that the headphone will not work, it just means that you must activate it in the audio control systems.
Locate the speaker symbol, which is usually shown at the extreme right in your computer taskbar along the bottom of the screen.
Right-click on the speaker symbol.
A menu opens, and you must highlight and click on Playback Devices.
Now a small window opens, showing the Playback tab, with all available speaker option.
One of the options should read something like this: " Speakers. AKG N90 headphones - Firmware version A2.12. Ready."- Highlight this option, and then click the "Set Default" button that is now available in the window. Audio should immediately be sent to the N90 headphones as a digital signal, which is then converted and amplified inside the headphones.
- Now you can enjoy world-class music listening.
Was this helpful? Thank you for your feedback! -
No, all recordings made on the telephone will be using the telephone's built-in microphone. Replay of the recording will be heard over the speaker afterwards, though, as long as it is paired to the telephone.Was this helpful? Thank you for your feedback!
-
This is correct. You can put the BDS x75 and x77 into Standby Mode by pressing and holding the ON/OFF Button, and this is not mentioned in the owner's manual. This stops the cooling fan, among other things.Was this helpful? Thank you for your feedback!
-
This is correct. You can put the BDS x75 and x77 into Standby Mode by pressing and holding the ON/OFF Button, and this is not mentioned in the owner's manual. This stops the cooling fan, among other things.Was this helpful? Thank you for your feedback!
-
When starting a workout in UA Record, the workout setup screen will display the heart rate monitor that is currently connected to your phone. Make sure your UA Sport Wireless Heart Rate are turned on and the logo is displaying in the heart rate monitor section.Was this helpful? Thank you for your feedback!
-
If I have a JBL Authentics L8 or L16 that is connected to Wi-Fi, do I need an Adapt to stream to it?Yes, you will need to connect an Adapt to stream music to the JBL Authentics products.Was this helpful? Thank you for your feedback!
-
Yes, you will need to connect an Adapt to stream music to the BDS x80, or older BDS models.Was this helpful? Thank you for your feedback!
-
Yes, you will need to connect an Adapt to stream music to the Aura.Was this helpful? Thank you for your feedback!
-
Spotify Connect needs to be connected to your Home network for it to work. Also it requires that you are a paid subscriber to Spotify Premium to open use of the Connect feature.Was this helpful? Thank you for your feedback!
-
AURA is DLNA compatible, which means that if you have a device capable of streaming DLNA content (AUDIO only), then it will be visible for these devices. If you do not see AURA on your network, please make sure you have connected it to the Wi-Fi and followed the procedure, as it requires to be connected via Wi-Fi.Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB200 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB250 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
-
Make sure your smart phone supports BLE (Bluetooth Low Energy) and it is connected to Smartbase via Bluetooth.Was this helpful? Thank you for your feedback!
-
The registration success rate and quality of voice commands depends on the performance of your smart phone’s microphone. Make sure that your smart phone’s microphone is unobstructed and you are speaking clearly when registering commands. If you continue to have issues, try registering using a family member or friend’s smart phone as a test. If voice command registration is successful with their device, the microphone on your smart phone may have issues.Was this helpful? Thank you for your feedback!
-
Android N, version 7.0 may have some compatibility issues, that are resolved with Android version 7.1. If your device is running Android N 7.0, please update it to 7.1 which should fix your issue.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The JBL Free will automatically switch to mono mode on the RIGHT ear when the call starts. After the call ends stereo music mode will automatically resume.Was this helpful? Thank you for your feedback!
-
Your device has entered full standby-mode, which means it shuts down all activity to have the lowest power consumption. This is a requirement for any product in Europe in order to reduce power consumption for devices in your home. To use the HK Remote app again, simply switch ON your device with the original remote control or the front panel on/off button.Was this helpful? Thank you for your feedback!
-
It is not possible to use the speaker while installing it to your WiFi network. Once you have successfully connected to the WiFi network, you can use Bluetooth and AUX again.Was this helpful? Thank you for your feedback!
-
It is not possible to setup a speaker to a hidden SSID Wi-Fi network. Please make it visible to install your OMNI+ speakers.Was this helpful? Thank you for your feedback!
-
Make sure your source device and AURA are on the same network. Then make sure your router is set to support older Wi-Fi protocols, such as b/g where the AURA is operating. Some routers have a function to disable older protocols and only use newer ones.Was this helpful? Thank you for your feedback!
-
Unfortunately, some Huawei phones are not able to stream music from the HK Controller app to 1st generation Omni speakers. However, the new Omni 10+, 20+, and 50+ have fixed this issue, and you will be able to stream music to them using your Huawei phone.Was this helpful? Thank you for your feedback!
-
The most important thing, is to be sure that both blue LEDs must flash quickly, one on the center speaker, one on the subwoofer. If just one of these LEDs does not flash quickly, pairing cannot take place. If it is difficult to make one of the LEDs change to quick flash, it may be that the button is held too long, or not pressed in the right angle. Try again with a short, firm press less then a second.Was this helpful? Thank you for your feedback!
-
It is important to use the correct HDMI connection on the BDS, marked with ARC. Also, the proper input must be selected with the AUX input selector button, which scrolls between the six AUX inputs. It always selects the AUX input that you used last, so once you have used the AUX ARC input, the BDS unit remembers it until you select another AUX input. Of course you have to have a TV which actually supports ARC.Was this helpful? Thank you for your feedback!
-
Look at the back of the primary speaker, which is the one with pause/play and volume controls. You will see a switch called "mode". This switch can be in either S or P position. S stands for Secondary, P stands for Primary. Switch to Primary, and your speaker will now open Bluetooth and will accept analog signals. (The Secondary position is used for systems where four speakers are in use, since only one speaker can act as primary speaker.)Was this helpful? Thank you for your feedback!
-
Please note that two types of ear tips are included with AKG N5005. The black ones are normal silicone tips, and they are fine for many users. The Milky-white ones are from the company SpinFit. They have a special middle section that permits the tip to swivel in all directions, making them able to adapt to various insertion angles. Please try both. For some, one is better, for some, the other one is better. You make the decision. In normal use, the tip that makes the best seal with your ear canal is the best choice, since bass reproduction is very dependent on this seal. However, some users may find that they prefer a slightly less tight seal.Was this helpful? Thank you for your feedback!
