With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.

In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.

The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.

Switch device ON.
Press and hold VOLUME+ and PLAY/PAUSE buttons until all lamps light up.
Device is now reset.

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.

By pressing and holding the Bluetooth and the Volume PLUS buttons at the same time. The software version is shown in the display.

You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of music

If your OMNI 50+ is completely drained, it will take 3,5 to 4 hours to fully charge. We advise to charge the Omni 50+ when it starts to blink red.

They support up to 8 paired devices without reset.

You can connect 3 smart devices ( iOS or Android ) simultaneously by Bluetooth. One when connecting via AUX cable.

You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.

The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water get into the speaker chamber, as it will damage the speaker drivers.

With a short press of the dedicated Bluetooth button on the underside of the right ear cup, it powered on and enter the pairing mode.
 

Connecting a Bluetooth device for your Enchant Soundbar

1. Make sure your Enchant soundbar is turned on by pressing the power button
2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar.
   1. Press the dedicated source button on top of your Enchant soundbar
   2. Press the source button until you see "Bluetooth" in the front of the Enchant display. Below is the order when using the source button (note that on Enchant 800 there is only 1 HDMI)

                  

3. The second option is to use the Remote control included with your Enchant soundbar.
   1. Press the "BT" button on your Remote control.
   2. The display will show "Bluetooth pairing"

                      

4. Now that your Enchant soundbar is in pairing mode it is now time to grab your mobile device.
5. Go to Bluetooth settings.

6. Press the enable Bluetooth button.

7. Select the Enchant soundbar and connect with Bluetooth.

You can now stream any music from your favorite device directly to the Enchant soundbar, ENJOY!
 

1. Open the Google Home app 2. Select the LINK VIEW 3. Select SETTINGS. 4. There is a line that says Paired Bluetooth Devices. 5. When you select it, it gives you the option to ENABLE PAIRING MODE. 6. Use your voice - "Hey Google, Open Bluetooth" and LINK VIEW will enable Bluetooth connection. You can disable Bluetooth using "Hey Google, Close Bluetooth" Once you have enabled Bluetooth pairing mode on your LINK VIEW, simply go into your Bluetooth settings menu on your mobile device and connect.

TV Connection HDMI (ARC)

 

1. Connect your HDMI cable (included in the box) to your TV.
2. Locate your TVs HDMI ARC (Audio Return Channel) port.
3. Find the HDMI OUT on the back of your Enchant 800 or 1300 Soundbar.
4. Now enjoy watching TV and listen to great audio through your Enchant soundbar.

Optical connection

1. Connect your Optical cable (included in the box) to your TV.
2. Find the Optical OUT connection on your TV.
3. Locate the Optical IN on the back of your Enchant soundbar.
4. Enjoy sound through the optical connection.

Using the HDMI Inputs

1. Find an HDMI Cable for your other devices.
2. Use the HDMI inputs on the Enchant Soundbar.
   1. NOTE: Enchant 800 only have one HDMI input port and Enchant 1300 has three HDMI input ports.
3. Switch source using your Remote control or pressing the source selector button.
4. The display on your Enchant device will show which HDMI input you are on.
5. Enjoy watching or playing through your Enchant Soundbar.

 

Citation One and Citation 100

1. Press the Bluetooth icon. Located on the top panel.
2. Go to -menuMake sure Bluetooth is 
3. Find your Citation speaker and connect.

         

4. You are now connected and ready to play music over Bluetooth, Enjoy!

Citation 300, 500, Bar and Towers

1. Swipe up on the display to find Bluetooth icon.
2. Tap Icon will light up Go to -menu Make sure Bluetooth is
3. Find your Citation speaker.

        

4. You are now connected and ready to play music over Bluetooth, Enjoy!

To control the Light show on your JBL Partybox device, simply press the dedicated "Light show" button located under the Bluetooth icon. There are 3 different light shows available when toggling through them, select your favorite one and have a blast. There is no app developed to control or modify these settings, all settings have to be done on the Partybox device.

Bluetooth Pairing

1. Press the button on the Partybox to start the pairing process.
2. Grab your device.
3. Go to settings --> Bluetooth --> Enable Bluetooth -->
4. Find the Partybox speaker you want to establish a Bluetooth connection to.

        

5. You now have a successful connection and can stream your favorite music.
   1. NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
   2. To stop Bluetooth broadcasting then insert a USB device.

If you have two of the same model Google Assistant speakers, you can create a stereo speaker system.

How to create a stereo pair...

1. Open the Google Home app
2. Find the speaker you want to setup in stereo pair
3. Find the speaker/room
4. Tap on Settings
5. Go to Sound Settings
6. Find the Speaker pair
7. You are now entering the setup page Tap
8. Find your speaker under the Pair with list and tap.
9. Move the speaker to be Left or Right side and press
   1. You can tap on Play sound to identify which speaker it is.
10. Find a name for your Stereo pair
11. It takes a minute to complete the setup.
12. When the configuration is done it will say Ready
13. Press Done

You have now completed the setup and created a Stereo pair sound experience.

NOTE 1:  This is only possible with two of the same speakers.  If they are not identical (Example: Citation 100 & Citation One), setting up a stereo pair will not be an option.

NOTE 2:  It is possible to make a stereo pair of a Mk1 with a Mk2. Setup as normal.
Airplay from the Mk2 will not be available.

NOTE 3: It is only possible to use Chromecast and Bluetooth in stereo, Airplay will be mono (and should be grouped in iOS Airplay menu.

 

In Power On mode, press and hold 'Volume+' together with 'Play/Pause' for more than 2 seconds. The speaker will power off and is now reset.

NOTE: Apple IOS users are not able to find their MAC address in Google Home app due to privacy policies in the USA and European market.

We advise setting up your device on a less secure network. Log into the router and retrieve the MAC address for your device then add it to your preferred network.

Instructions below are for Android only

1. Open your Google Home app 
2. Enable Bluetooth  on your device.
3. Enable Location service  on your Android device.
   1. Remember to "Allow" Google Home to view your location while using the app (You are asked during setup of the Google Home app).
   2. In case you denied access go to Settings  Apps  Google Home  Permissions  Allow to view Location.
4. When you at selecting the Wi-Fi network from the list of available networks, before tapping on your network you need to get the MAC address.
   1. Tap  the  located top right corner.
   2. In the pop-up menu press "Show MAC address" Write down the MAC Address.

You can now add the MAC address to your local Wireless router or system if your configuration requires this before installing the device on your network.

Finding the MAC address after speaker is installed

1. Open your Google Home app .
2. Tap on  to view your home.
3. Find your room .
4. In the top right corner tap Settings icon .
5. ​Scroll down to the bottom of the screen. You will see some system information and the MAC address as well.

Finding the software version

1. Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
2. A voice will start prompting numbers which indicates the current software version.

1. Touch the microphone icon on the screen to mute the Google Voice assistant microphone.
   1. NOTE: Google Assistant will not work when the microphone is muted.
2. Touch and press it again to unmute the microphone.
3. You can now give it any voice commands that you would like.

How to pair an Enchant Subwoofer with your Enchant bar

1. Go to the back of your Enchant soundbar (800 or 1300)
2. Press the "Subwoofer pairing" button for 2 seconds.

3. In front of your Enchant display, it will say "Subwoofer pairing"
4. Go to the back of your Enchant subwoofer.
5. Press the "Subwoofer pairing" button.

6. The small LED indicator will start to flash rapidly and when the connection is successful, it will be a steady light.

You now have more bass performance and can enjoy deeper richer sound!

1. Power on your Enchant 800 or Enchant 1300 Soundbar. 2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar. 2.1. Press the dedicated source button on top of your Enchant soundbar source 2.2. Press the source button until you see "Bluetooth" in the front of the Enchant display. 3. The second option is to use the Remote control included with your Enchant soundbar. 4. Press the "BT" button on your Remote control. 5. The display will show "Bluetooth pairing". 6. Go to your Bluetooth settings menu on your mobile device. 7. Enable Bluetooth and connect to your Enchant 800 or Enchant 1300 Soundbar.