REFERENCE 1300A

REFERENCE 1300A

Subwoofer Amplifier - Digital (200 watts x 1)

Vendido desde 2007 hasta ahora

Producto predecesor: REFERENCE 311A
Hecho en: China

Documentos y descargas

Especificaciones del producto

Input Sensitivity
100mv
Signal-to-Noise Ratio
>85dB (ref 1W output @ 4Ω)
Effective damping factor
6.3 at 4 ohms
Dynamic power
342 watts at 2 ohms
CEA Rated
Yes
Amplifier Power (RMS)
200 watts x 1 channel @ 4 ohms and ≤1% THD + N
Signal-to-Noise Ratio
85dBA (reference 1 watt into 4 ohms)
Dynamic Power
342 watts @ 2 ohms
Effective Damping Factor
6.3 @ 4 ohms
Frequency Response
11Hz – 330Hz (-3dB)
Maximum Input Signal
6V
Input Sensitivity
MAXIMUM... 100mV
MSRP U.S.
$229.95 each

300-Watt mono subwoofer amplifier with on-board electronic crossover and variable bass boost circuit.

Efficiency is the benefit of the Infinity Reference Series Class D subwoofer amplifiers. A higher percentage of the power the amp extracts from the car’s charging system is converted into output to the speakers, and less is wasted as heat. That is really important if you're trying to provide power to a 1000-watt amplifier. Class D technology turns the analog input signal into a series of pulses that can be amplified more efficiently by transistors used as switches, rather than valves. They're either on and operating at their most efficient level, or they’re off. The pulses are converted back into an analog signal by an output filter.
All Infinity amplifiers are tested in accordance with CEA-2006, which provides a testing procedure to help customers compare amplifiers accurately – apples to apples. Specs are based on industry-accepted standards, rather than on the whims of amplifier companies’ marketing departments. Look for the CEA-2006 logo when comparing amplifiers, to be sure you’re getting the power you’re paying for.
Class AB full-range amplifiers offer audiophilequality performance and the best compromise between efficiency, low distortion, maximum available headroom and output power.
Infinity amplifiers are tested according to the strictest and most demanding reliability-testing regimen ever designed for car audio amplifiers. They are shaken, baked, frozen, dropped and shocked – all while they’re operating. When they’ve passed all these tests, they are tested again. The result is a series of amplifiers that just don’t break.
provides superior control and adjustability, compared to traditional bass-boost. DBO is a 2nd order high-pass filter that can be adjusted between 20Hz and 80Hz. The boost (or Q) adjustment boosts the signal above the highpass filter frequency. Used with a sealed box, it can help to increase output for more “fun” if it’s set to about 45Hz. If it’s used with a vented box, it should be set at or slightly below the tuned frequency of the box. That will prevent woofer unloading, and provide more output at the frequency where the box is tuned and the woofer’s excursion is minimized – where it can handle more power.
The amount of bass in popular recordings differs greatly from track to track. Give your customer as much control as you see fit with the RLC. It varies the output of the amplifier from no output up to the maximum output level that you set with the input sensitivity control.

¿No encuentras lo que buscas?

Llámanos

Llámanos

Habla con un experto sobre nuestros productos
Llámanos a este número: 55-5328-1023

Lunes - Viernes: 09:00 AM -06:00 PM (Hora Centro)

Envíanos un correo electrónico

Envíanos un correo electrónico

¡Estamos aquí de lunes a viernes para responder sus correos lo antes posible!

Envíanos un correo electrónico
message