POWER P660C
6 1/2 inch 2-Way Component System
Vendido desde 2008 hasta ahora
| Producto predecesor: | POWER P650C |
|---|---|
| Hecho en: | China |
Empezando con su POWER P660C
Registre su producto
¿Es propietario de este producto? ¡Regístrelo aquí! Y reclame su garantía o servicio fácilmente
Regístrese ahoraDocumentos y descargas
Especificaciones del producto
- Series
- Power Series
- Size
- 6-1/2
- Type
- Two-Way
- MSRP U.S.
- $269.95 per pair
- Frequency Response
- 45Hz–23kHz
- Sensitivity
- (2.83V@1m) 94dB
- Power Handling (Peak)
- 270W
- Power Handling (RMS)
- 90W
- Nominal Impedance
- 2 ohms
- External Diameter (mm)
- 158.2
- Mounting Depth Woofer (mm)
- 57.3
- Mounting Depth Woofer (in)
- 2-1/4
- Mounting Cutout Diameter (mm)
- 128.6
- External Diameter (in)
- 6-1/4
- Mounting Cutout Diameter Tweeter (mm)
- 47
- Mounting Cutout Diameter Tweeter (in)
- 1-7/8
- Mounting Cutout Diameter (in)
- 5-1/16
- High-Frequency Transducer
- PlusOne® HCL™ honeycomb-laiminate cone
6-1/2 inch 2-Way Component System with Plus One HCL woofer and high-bandwidth edge-driven textile dome tweeter. This system features the I-Mount (patent # 5,859,917) tweeter mounting system and a computer optimized outboard passive crossover network with tweeter level control.
The P660C woofer cone is exceptionally stiff and lightweight, with up to 25 percent more active surface area than a standard cone of the same size. Patented Plus One® (patent no. 7,548,631) woofer cones and long-excursion surrounds boost bass output and efficiency by two to three decibels compared with competing products.
The JBL® P660C has a tweeter high-cut filter on the crossover that allows you to attenuate the tweeter by -6dB to optimize performance and optimize blend with the the mid/woofer based on installation location.
You’ll have 90W RMS and 270W peak power handling with a 94dB sensitivity rating. And you can push it to the limit. You’ll hear true JBL® sound, with nothing under- or over-emphasized. The P660C has a frequency response of 45Hz to 23kHz.
In addition to better sound quality, the new, proprietary, JBL®-patented woofer design offers far higher SPL (sound pressure level) and better suspension symmetry than the previous generation of products.
These speakers make the best use of any amplifier by providing an optimum 2-ohm load. They use a lower-impedance voice coil than a typical speaker to extract the most power and performance possible from all amplifiers engineered to drive loads of 4 ohms or less.
The P660C component system networks have in-line polypropylene caps and low-insertion-loss air-core inductors. Outboard crossovers are integrated into a harness connected to each speaker model for easy installation. Oversized Direct-Connect terminals ensure perfect connectivity for bare speaker wires.
The I-Mount™ (patent no. 5,859,917) tweeter-mounting system allows easy and versatile installation of tweeters in each of the component systems. It includes a flush cup and surface-mount mounting hardware. With a 1-3/4” cutout and a 1" mounting depth, installation becomes a snap. This allows the tweeter to be flush-mounted and can be angled up to ±40 degrees. Locknuts
Realistic, live-performance sound needs to be loud. But it also needs to be accurate and distortion-free. Others will give you miniatures for your car, but the JBL® brand uses an edge- driven textile-dome tweeter like high-end home audio loudspeakers. Crank it up. You get less distortion at even high volumes and superior integration with the mid/woofer.
Imágenes y vídeos
¿No encuentras lo que buscas?
Llámanos
Habla con un experto sobre nuestros productos
Llámanos a este número:
55-5328-1023
Lunes - Viernes: 09:00 AM -06:00 PM (Hora Centro)
Envíanos un correo electrónico
¡Estamos aquí de lunes a viernes para responder sus correos lo antes posible!
