Reference 475a

Reference 475a

4-Channel Full-Range Amplifier

Såld från 2007 tills nu

Föregående produkt: REFERENCE 7541A
Tillverkade i: Netherlands

Dokument och hämtningar

Produktspecifikationer

Signal-to-noise ratio
85dBA (reference 1 watt into 4 ohms)
Dynamic power
117 watts at 2 ohms
Effective damping factor
6.3 at 4 ohms
Frequency response
10Hz – 100Hz (–3dB)
Maximum input signal
6V
Maximum sensitivity
100mV
CEA Rated
Yes
Amplifier Power (RMS)
180 watts x 2 channel @ 4 ohms, 14.4V supply and ≤1% THD + N
Amplifier Power (RMS)
75 watts x 4 channel @ 4 ohms, 14.4V supply and ≤1% THD + N
Signal-to-Noise Ratio
85dBA (reference 1 watt into 4 ohms)
Dynamic Power
117 watts @ 2 ohms
Effective Damping Factor
6.315 @ 4 ohms
Frequency Response
10Hz – 100kHz (-3dB)
Maximum Input Signal
6V
Input Sensitivity
MAXIMUM... 100mV
MSRP U.S.
$279.95 each
Dimensions (L x W x H)
14-3/16" x 9" x 2-11/16" (360mm x 229mm x 68mm)

4-Channel full-range amplifier with on-board electronic crossover and variable bass boost.

Efficiency is the benefit of the Infinity Reference Series Class D subwoofer amplifiers. A higher percentage of the power the amp extracts from the car’s charging system is converted into output to the speakers, and less is wasted as heat. That is really important if you're trying to provide power to a 1000-watt amplifier. Class D technology turns the analog input signal into a series of pulses that can be amplified more efficiently by transistors used as switches, rather than valves. They're either on and operating at their most efficient level, or they’re off. The pulses are converted back into an analog signal by an output filter.
All Infinity amplifiers are tested in accordance with CEA-2006, which provides a testing procedure to help customers compare amplifiers accurately – apples to apples. Specs are based on industry-accepted standards, rather than on the whims of amplifier companies’ marketing departments. Look for the CEA-2006 logo when comparing amplifiers, to be sure you’re getting the power you’re paying for.
Class AB full-range amplifiers offer audiophilequality performance and the best compromise between efficiency, low distortion, maximum available headroom and output power.
provides superior control and adjustability, compared to traditional bass-boost. DBO is a 2nd order high-pass filter that can be adjusted between 20Hz and 80Hz. The boost (or Q) adjustment boosts the signal above the highpass filter frequency. Used with a sealed box, it can help to increase output for more “fun” if it’s set to about 45Hz. If it’s used with a vented box, it should be set at or slightly below the tuned frequency of the box. That will prevent woofer unloading, and provide more output at the frequency where the box is tuned and the woofer’s excursion is minimized – where it can handle more power.
Reference Series amplifiers include 2nd order (12dB/octave) slopes and are continuously variable from 32Hz to 200Hz.
provides up to 12dB of boost at 50Hz in the Reference Series full-range amplifiers.
eliminate the need for additional solder-on or crimp-on terminals and provide an easy and reliable connection for power, ground and speaker wires.
eliminate the need for signal splitters.
The amount of bass in popular recordings differs greatly from track to track. Give your customer as much control as you see fit with the RLC. It varies the output of the amplifier from no output up to the maximum output level that you set with the input sensitivity control.

Hittade du inte det du sökte efter?

Ring oss

Ring oss

Ring oss på: +46 850512632

Måndag – fredag: 09:00-17:00

Skicka e-post till oss

Skicka e-post till oss

Vi är här måndag-fredag för att svara på ditt mejl så fort vi kan!

Skicka e-post till oss
Chatta med oss

Chatta med oss

Chatta på engelska:
Måndag – fredag: 09:00-18:00
Lördag – söndag: 10:00-16:00

message

WhatsApp oss

WhatsApp-support endast på engelska

Skicka ett meddelande till oss på engelska här 

Måndag – fredag: 09.00-18.00
Lördag – söndag: 10:00-16:00