How To
How To
1871 results
-
To use the Onyx Studio 2 with a PC or MAC, please make sure that you have the correct Bluetooth driver, that supports A2DP Audio Codec.Was this helpful? Thank you for your feedback!
-
Typically when we are talking about projectors, they are normally installed in a place where the HDMI cable is too long, and the signal has a hard time reaching the AVR. It is also possible that the projector is not compatible with the AVR. To be sure it works with the AVR, please move projector closer and use a short HDMI cable. We recommend a cable that is 3 meters in length or less. If the projector works with the shorter cable, and you have no choice but to use a longer cable, you will need an HDMI repeater/amplifier/eq/booster (name varies depending on the manufacturer), to boost the signal so that it can make it all the way from the AVR to the projector.Was this helpful? Thank you for your feedback!
-
Close and restart the Google Home app, or restart your phone. Start the Google Home app again, and the speaker should now appear.
Was this helpful? Thank you for your feedback! -
Please make sure that the audio out format is set to PCM in the TV. Dolby Digital or other surround formats will not work with the BTA 20 transmitter.Was this helpful? Thank you for your feedback!
-
The Harman AVR App controls your receiver through your smartphone, which communicates via your wireless home network. Please make sure that your AVR is properly connected to your network router, with cable for the smaller models. If you have no wireless home network, you cannot use the app.Was this helpful? Thank you for your feedback!
-
I have downloaded the HK Remote app and connected to my AURA Studio, but i do not see it in the app?AURA Studio is not supported via our app, and that means you cannot change any settings on it.Was this helpful? Thank you for your feedback!
-
Please make sure that your BDS is connected to the home network router also used by your smartphone.Was this helpful? Thank you for your feedback!
-
Please place your AVR in full Standby by holding the Power Button for at least three seconds. Now, when you switch it ON again, the problem should have disappeared. Please note that Sleep Mode is not sufficient, you must use full Standby.Was this helpful? Thank you for your feedback!
-
Our Control X Wireless speakers use Wi-Fi 2.4 GHz network to connect them. If there are any obstacles or people blocking the connection, it can cause interference. We suggest positioning the speakers on a high-level surface or shelf, to avoid any interference.Was this helpful? Thank you for your feedback!
-
Please make sure that if you use 5GHz or 2.4GHz Wi-Fi, all your speakers are connected to either 2.4GHz or all are connected to 5GHz Wi-Fi to have the best performance.Was this helpful? Thank you for your feedback!
-
In the Owner's Manual, we say "Up to 30 m (between primary and secondary speakers)". This applies to an ideal setup, with no obstacles and interference, and if there is interference at this distance, you will have to reduce the distance between the speakers. Please check for any objects and obstacles that could cause interruptions.Was this helpful? Thank you for your feedback!
-
The first 105 files are registered right away. If you know that you have more files in the DLNA system, wait for close to a minute, while the BDS -75 / -77 registers the additional files. After a short while, it will begin counting until all files are registered, or until the maximum of 2000 files is reached.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)